• 한국지진공학회논문집
• /
• 제7권2호
• /
• pp.85-92
• /
• 2003

본 논문에서는 교량의 건전도 감시용 자립형 계측유닛을 위한 교량의 상시진동을 이용한 진동발전시스템을 제시하였다. 본 연구에서는 전기자 반작용의 영향을 최소화한 새로운 구조의 진동발전기를 제안하고, 기계적 및 전기적인 설계식을 유도한 다음, 시험용 진동발전기를 제작하였다. 또한, 매우 작은 발전 전류의 축전시스템에 대하여 고찰하고 개선점을 도출하였다. 축전시스템에 대한 고찰 결과, 정류기에 사용된 다이오드 특성이 충전과정에서 지배적임을 밝혔다. 마지막으로, 진동발전시스템 모델에 실측 남해대교 가속도 데이터를 적용한 시뮬레이션과 실내 실험을 수행하였고, 제작된 시험용 진동발전기의 적용성과 효용성을 확인할 수 있었다.

• 한국수소및신에너지학회논문집
• /
• 제20권5호
• /
• pp.410-415
• /
• 2009

A hydrogen cooling method is used in a power generator for removing the unnecessary heat due to the windage loss of a rotor and the joule heat of a stator. A MEA (Membrane Electrolyte Assembly) hydrogen generator has been developed and applied as a hydrogen supplying system for the cooling of a 350MW power generator. As a field application result, the average potential of eleven cells and the voltage efficiency were measured 2.26V/cell and 65.4% (Higher Heating Value) respectively at the hydrogen pressure of 6 Bar, the hydrogen flow rate of 9.1L/min, and the current of 150A.

• 한국도로학회논문집
• /
• 제16권6호
• /
• pp.51-57
• /
• 2014

PURPOSES : An conventional method for electric power generation is converting thermal energy into mechanical energy then to electrical energy. Due to environmental issues such as global warming related with $CO_2$ emission etc., were the limiting factor for the energy resources which resulting in extensive research and novel technologies are required to generate electric power. Thermal energy harvesting using thermoelectric generator is one of energy harvesting technologies due to diverse advantages for new green technology. This paper presents a possibility of application of the thermoelectric generator's application in the direct exchange of waste solar energy into electrical power in road space. METHODS : To measure generated electric power of the thermoelectric generator, data logger was adopted as function of experimental factors such as using cooling sink, connection methods etc. Also, the thermoelectric generator、s behavior at low ambient temperature was investigated as measurement of output voltage vs. elapsed times. RESULTS : A few temperature difference between top an bottom of the thermoelectric generator is generated electric voltage. Components of an electrical circuit can be connected in various ways. The two simplest of these are called series and parallel and occur so open. Series shows slightly better performance in this study. An installation of cooling sink in the thermoelectric generator system was enhanced the output of power voltage. CONCLUSIONS : In this paper, a basic concepts of thermoelectric power generation is presented and applications of the thermoelectric generator to waste solar energy in road is estimated for green energy harvesting technology. The possibility of usage of thermoelectric technology for road facilities was found under the ambient thermal gradient between two surfaces of the thermoelectric module. An experiment results provide a testimony of the feasibility of the proposed environmental energy harvesting technology on the road facilities.

• Journal of Power Electronics
• /
• 제14권3호
• /
• pp.580-591
• /
• 2014

This paper concerns a three-phase self-excited induction generator used for autonomous power generation. It presents a robust control strategy which makes it possible to maintain the frequency quasi constant during the voltage regulation without any control loop on this variable. This strategy, which also prevents the machine disengagement, uses as power converter a simple dimmer. The obtained theoretical and/or numerical results are validated on a laboratory test bench that allows the analysis of this control law effectiveness.

• 한국자동차공학회논문집
• /
• 제11권5호
• /
• pp.163-169
• /
• 2003

Modeling of engine-generator system and its control responses are investigated using high performance generator controller. The nonlinear engine is modeled using mean torque production model based on experimental engine map. In case of diesel engine. the amount of injected fief is decided by engine controller depending on the APS(Acceleration Position Sensor) value. An electromechanical generator model contains electrical circuits and moment of inertia. The generator controller maximizes the performance of generator using decoupling and linearized current feedback control. The generator control system consists of 3-phase IGBT inverter and controller board based on 32 bit floating point DSP. Field oriented control algorithm with digital current feedback control at 10kHz sampling enabled high performance torque and speed control of induction machine. Not only the steady state but also the transient state responses can be evaluated through a batch test of the engine generator system. Developed engine and generator modeling and control can be utilized in various applications such as Series Hybrid Electric Vehicle(SHEV), engine-generator for emergency, and other hybrid generation systems.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2003년도 춘계종합학술대회
• /
• pp.313-316
• /
• 2003

본 논문에서는 교량의 건전도 감시용 계측 유닛에 사용되는 충전시스템을 위한 교량의 상시진동을 이용한 자립형 진동발전기에 대하여 연구하였다. 본 연구에서는 전기자 반작용의 영향을 최소화한 진동발전기를 제안하고, 기계적 및 전기적인 설계식을 유도한 다음, 시험용 진동발전기를 제작하였다. 아울러, 실내 자유진동 실험을 수행하였고, 축전시스템에 대한 실험 결과, 정류기에 사용된 다이오드 특성이 충전과정에서 지배적임을 확인하였다. 또한, 남해대교의 진동 데이터를 Pilot 발전기에 적용하여 시뮬레이션 한 결과 진동발전기의 적용성과 효용성을 확인할 수 있었다.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2005년도 학술대회 논문집
• /
• pp.95-99
• /
• 2005

This paper presents a general proposal to design and calculate the performance of a tubular permanent magnet linear generator treated here on the basis of the Finite Element Method. Optimizing the linear generator dimensions reduces the cogging force, which occurs due to the interaction between stator teeth and the permanent magnets. The generated AC voltage is analyzed and evaluated for both no load and load cases to take the armature reaction effects on the air gap flux density. A repetitive routine is followed to calculate the output AC voltage from the change of flux and the speed of the single-phase linear generator. The AC output voltage is calculated for different resistive loads, and hence, the linear generator load characteristic is obtained. The designed linear generator is capable to generate an output power of 5.3kW with AC output voltage of 222V with an efficiency of 96.8% at full load of 23.8A. The full load current is chosen based on the thermal properties of the coil wire insulations.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1446-1448
• /
• 1997

TEC(Thermoelectric conversion) is direct conversion method between thermal energy and electric energy. We studied on the mechanical, electrical and thermal properties of thermoelectric module and made experimental thermoelectric generator with BiTe material.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 C
• /
• pp.1044-1047
• /
• 1999

This paper deals with the dynamic property of ground overvoltage relay in large turbine generator. Relay operation is based on detecting the fundamental voltages originating from the generator. Calculations of fault voltage and current are reviewed for the neutral ground resistance. The frequency, ampitude and waveform of individual harmonics were measured using power quality analyzer and memory hi-corder at the secondary side of ground potential transformer. The ac and dc high-potential tests were applied to evaluate the condition of generator, main and auxiliary transformer, isolated phase bus, potential transformer, surge capacitor and arrester.

• 한국압력기기공학회 논문집
• /
• 제13권2호
• /
• pp.31-37
• /
• 2017

The heat transfer function or thermal performance is the most important function of the steam generator component in nuclear power plants. The declining of thermal performance, fouling does not affect the electric power of the nuclear power plant within a certain fouling level, but it affects the output when goes beyond the governor valve wide open of the turbine. The VWO steam pressure can be predicted through the thermal performance evaluation of steam generators in the nuclear power plant. In consideration of the fouling characteristics of the steam generator, methods of the thermal performance evaluation and fouling cases are reviewed, and also the critical VWO value is estimated through the actual thermal performance evaluation. It is necessary to apply the VWO theory based on the thermal performance of the steam generators.