• 한국전기전자재료학회논문지
• /
• 제25권10호
• /
• pp.824-829
• /
• 2012

Zn wires have been electrically exploded in methanol or distilled water using the pulsed power technologies. The nanopowders produced by the explosions have been observed by using SEM and TEM, and analyzed its phase by using EDS and XRD. The nanopowders produced in distilled water showed ZnO phase only. On the other hands, the nanopowder produced in methanol showed mixed phases with Zn and ZnO. The HR-TEM images of the nanopowders produced in methanol showed that the some particles have been coated with carbon like materials. It is considered that the carbon coatings could be depended on the positions of the particles during the plasma state formed by explosion.

• 한국안전학회지
• /
• 제22권6호
• /
• pp.41-45
• /
• 2007

Short circuit and ground fault account for the primary causes of electrical fires. In this research, real-scale experiments were conducted to assess the possibility of electrical fires due to these causes. The experiment conditions were identical with an actual fire accident, in which the power cable was supported by an iron fence. The purposes of this research are to investigate the short circuit caused by wire cutting, the conductivity of the iron fence depending on its coating conditions, and the ground fault of one wire or two wires in an effort to reconstruct the fire accident. The test results show that, owing to the instant operation of circuit breaker in the moment of short circuit or ground fault, the generated ignition energy is far less than necessary to start an ignition. Therefore it is concluded that electrical fire is highly unlikely if the electric system is protected by a circuit breaker with normal functions.

• Structural Engineering and Mechanics
• /
• 제51권4호
• /
• pp.663-683
• /
• 2014

In order to study the dynamic failure mechanism and aseismic measure for high concrete gravity dam under earthquake, the comparative models experiment on the shaking table was conducted to investigate the dynamic damage response of concrete gravity dam with and without the presence of reinforcement and evaluate the effectiveness of the strengthening measure. A new model concrete was proposed and applied for maintaining similitude with the prototype. A kind of extra fine wires as a substitute for rebar was embedded in four-points bending specimens of the model concrete to make of reinforced model concrete. The simulation of reinforcement concrete of the weak zones of high dam by the reinforced model concrete meets the similitude requirements. A tank filled with water is mounted at the upstream of the dam models to simulate the reservoir. The Peak Ground Acceleration (PGA) that induces the first tensile crack at the head of dam is applied as the basic index for estimating the overload capacity of high concrete dams. For the two model dams with and without strengthening tested, vulnerable parts of them are the necks near the crests. The results also indicate that the reinforcement is beneficial for improving the seismic-resistant capacity of the gravity dam.

• 한국태양에너지학회 논문집
• /
• 제33권4호
• /
• pp.8-14
• /
• 2013

The conversion of solar energy into acoustic waves is experimentally studied. Measurements were made on the Sound Pressure Level(SPL), onset time and the temperature gradient across the stack, with the Cell Per Square Inch(CPSI) of stack changed. A pyrex resonance tube is used with a honey-comb structure ceramic stack along with Ni-Cr and Cu wires. An AL1 acoustical analyzer was used to measure the SPL and frequency of acoustic waves whereas K-type thermocouples were hired to estimate temperature gradients. As a result, when the supply electric power was 25W, maximum SPLs of 104.1 dB, 109.4 dB and 112.8 dB were detected for the stacks of 200, 300 and 400 CPSI and their respective stack positions of 70mm, 60mm and 50mm from the closed end.

• 전기전자학회논문지
• /
• 제23권2호
• /
• pp.747-750
• /
• 2019

웨어러블 디바이스는 일상생활에서 실질적으로 필수적이며 사용자들에게 편리하게 이용되고 건강관리와 의학 분야 등에 활용되고 있다. 전력분야에서 전원 배터리의 사용시간의 한계를 극복하고 효율적인 충전방법에 관한 많은 연구가 진행되고 있다. 무선전력전송은 전선을 사용하지 않고 무선으로 전기장을 부하에 전력을 전달하는 기술이다. 이 전송기술은 저 전력의 스마트폰에서부터 고 전력을 사용하는 철도 충전시스템까지 응용분야가 다양하다. 충전방식은 유도방법과 자기공진방법의 2 종류로 나누는데 자기공진주파수는 13.45 Mhz를 사용하였다. 본 연구에서는 전송효율을 측정 비교하기 위하여 2 종류의 하드웨어를 구현한 후 비교하는데 있다.

• 한국공간구조학회논문집
• /
• 제20권4호
• /
• pp.185-192
• /
• 2020

A new lighting support structure composing of two-way wires and pulley, a pulley-type wireway system, was developed to improve the seismic performance of a ceiling type lighting equipment. This study verifies the seismic performance of the pulley-type wireway system using a numerical approach. A theoretical model fitted to the physical features of the newly-developed system was proposed, and it was utilized to compute a frictional coefficient between the wire and pulley sections under tension forces. The frictional coefficient was implemented to a finite element model representing the pulley-type wireway system. Using the numerical model, the seismic responses of the pulley-type wireway system were compared to those of the existing lighting support structure, a one-way wire system. The addition of the pulley component resulted in the increasement of energy absorption capacity as well as friction effect and showed in significant reduction in maximum displacement and oscillation after the peak responses. Thus, the newly-developed wireway system can minimize earthquake-induced vibration and damage on electric equipment.

• 한국음향학회지
• /
• 제29권6호
• /
• pp.395-401
• /
• 2010

리어스는 그레이나 벨 등보다 훨씬 앞서서 도선을 통해 목소리를 전달하는 데 성공했기 때문에 전화기의 발명자라고 불리는 것이 마땅하지만 살아 있는 동안 그의 위대한 발명품으로 영예를 누리지 못했다. 그는 과학자 집단에 속해 있었으므로 그의 연구를 특허를 낼 수 있는 발명품이 아니라 과학적 발견으로 제시하였다. 또한 그는 유럽 음향학의 실험 전통에 따라 단속적 전기를 사용하였기에 그의 전화기는 통화음질에 치명적 결점을 갖게 되었다. 반면에 전기와 음향학에 초보자였던 벨은 소리 신호를 전송하기 위해 가변 전류를 사용하였고 그것은 라이스의 전화기보다 더 나은 통화 음질을 보장하였다.

• 대한안전경영과학회지
• /
• 제26권1호
• /
• pp.31-38
• /
• 2024

In this paper, as there are many cases of fires occurring due to the failure or inoperability of the thermostat of electronic products, the purpose is to test and analyze the risks and probabilities through fire cases and reproduction experiments, and suggest countermeasures. Among electronic products, water purifiers are composed of a refrigerant system with a compressor to make cold water, a heating device to make hot water, and an electric device used as an energy source. Due to the nature of the water purifier manufacturing, these devices are subject to a lot of moisture and dust. etc. exist in large quantities and use electrical energy, so there is a possibility of fire due to short circuit in the wire, electrical abnormal overheating (tracking phenomenon) in the thermostat, electronic board, starting relay, etc., and overheating of the heating device (Band Heater). there is. Therefore, in order to prevent fires from these devices, a system to remove foreign substances inside the water purifier is necessary, the use of heat-resistant (fire-resistant) wires for electrical devices is essential, and the use of non-combustible materials (semi-combustible materials) for each part is necessary to prevent fire. The risk must be eliminated through prevention and combustion expansion prevention devices.

• ETRI Journal
• /
• 제46권4호
• /
• pp.581-594
• /
• 2024

In this study, a planar printed circuit board (PCB) coil with FR4 substrate was designed and simulated using the finite element method, and the results were analyzed in the frequency domain. This coil can be used in wireless power transfer (WPT) as a transmitter or receiver, eliminating wires. It can also be used as the receiver in radio frequency energy-harvesting (RF-EH) systems by optimizing the planar PCB coil to convert radio-wave energy into electricity, and it can be employed as an excitation (transmitter) or receiver coil in nuclear magnetic resonance (NMR) spectroscopy. This PCB coil can replace the conventional coil, yielding a reduced occupied volume, a fine-tuned design, reduced weight, and increased efficiency. Based on the calculated gain, power, and electromagnetic and electric field results, this planar PCB coil can be implemented in WPT, NMR spectroscopy, and RF-EH devices with minor changes. In applications such as NMR spectroscopy, it can be used as a transceiver planar PCB coil. In this design, at frequencies of 915 MHz and 40 MHz with 5 mm between coils, we received powers of 287.3 μW and 480 μW, respectively, which are suitable for an NMR coil or RF-EH system.

• Korean Journal of Acupuncture
• /
• 제40권4호
• /
• pp.156-168
• /
• 2023

Objectives : This study aimed to determine the status of thermal stimulation devices approved in Korea for medical applications over the past 10 years, and based on this, to obtain insight for future thermal treatment in Korean medical institutions. Methods : We searched the item classification list entitled "Regulations on Medical Device Items and Rating by Item" from the Ministry of Food and Drug Safety Notice No. 2021-24, 2021 (Enforced March 19, 2021; www.mfds.go.kr) for individually licensed heaters using the terms "heat" and "heating". Results : We identified 17 items of thermal stimulation product group, of which 1,308 devices were licensed by February 4, 2022, and 53.2% of them (n=696) were devices with valid permits for distribution in Korea. Among the licensed devices, heating pad systems under/overlay (electric, home use) were approved the most, but combinational stimulator (for medical use, home use; Grade 2) accounted for the highest percentage among the current valid permission. Moxibustion apparatuses were licensed separately for electrical use and non-electrical use, and occupied a low percentage of the total devices. We analyzed 307 devices that were accompanied by technical documents and found that the heat sources were wires in 145 (47.2%), infrared rays in 44 (14.3%) and ultrasonic waves in 42 (13.7%) devices. Most (83.1%) devices were used for pain relief, while other applications included beauty, cancer treatment, maintenance of infant body temperature, and healing fractures. Conclusions : Thermal stimulation devices accounted for about 0.9% of all medical devices, and among them, combinational stimulators and heating pad systems under/overlay had the most valid permits. Thermal stimulation devices using heating wires and infrared rays were the most prevalent, and most were used to relieve pain. In order to develop a range of thermal stimulation devices that can be utilized in Korean medical institutions, it is imperative that they have potential applications beyond pain management, addressing various medical purposes. To achieve this, foundational research is necessary to effectively apply diverse heat sources based on medical objectives.