• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.10
• /
• pp.6270-6275
• /
• 2014

The paper reports an improvement method on torque ripples of multi-pole interior permanent magnet synchronous motor (IPMSM) applied to a traction motor for hybrid electric vehicles. In the case of multi-pole IPMSM, the magnetic flux generated by a permanent magnet tends to leak through the bridge of the rotor without a link with stator windings. The slit design on the rotor surface was proposed to reduce torque rippling and increase the output power by reducing the leakage flux. Two design parameters for the slit are suggested for optimal design using the response surface method. As an analysis method, the 2D finite element method (FEM) was applied to consider magnetic saturation effect.

• Journal of the Korean Society of Safety
• /
• v.33 no.2
• /
• pp.14-20
• /
• 2018

In this study, we analyze the current status of major disasters in distribution works and propose safety measures through the distribution live-line work method and electric shock risk assessment. The result of analyzing the ratio of electric shocks to the occurrence of industrial accidents in the recent 13 years shows that the death rate is higher than other industries, especially the construction industry occupying most of the disaster, and it is higher than the collapse disaster. We analyze statistic data of 101 victims selected as core words of live work, distribution line, pole and 22.9 kV in the investigation report of major accident of electric shock fatal from 2001 to 2014. The safety measure was established through the risk assessment of the distribution method using the standard model of the risk assessment based on the results of electric shock analysis on the distribution line. In order to prevent the electric shock accident which is recently being discussed, the risk assessment procedure were carried out in the above-mentioned 22.9kV special high voltage live-line operation method. We derived the risk reduction plan for the distribution line from the results of the major accidents statistic and demonstration of the line works.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1942-1944
• /
• 2004

In this paper, we studied on the potential characteristics of human-body contacted the charging part. A charging part of electrical facilities and the earth are simulated by the e1ectrode pole and conductive rubber plates respectively. As the results of these follows, when the potential distribution of the human-body contacted the charging part is far from the electrode pole, a lot of currents flow through the human-body. Besides human-body non-contacted the charging part is affected by step voltage. Therefore, we could find out the causes of the electric shock accidents and be expected to the data for minimization of human error occurred the workspace.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.609_610
• /
• 2009

This paper deals with experimental verifications and the electromagnetic characteristics analysis of multi-pole permanent magnet (PM) generator for small-scaled wind power system. Field distribution due to PMs and winding current, cogging torque considering skew effect are analyzed. In addition, using the equivalent circuit method and dynamic d-q method, generating performance analysis is performed. Analysis results are validated by comparison with nonlinear finite element analyses and experimental results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.886-889
• /
• 2002

This paper describes the characteristic analyses and a new design of the bushing for the pole transformers. The mechanical breakdown of the upper part of the bushing was frequently occurred. This caused the leakage of mineral oil, resulted in the interruption of electric power. Therefore, the bushings were investigated by the material analytical method and Finite Element Method. The analyses were performed by the Induced Coupled Plasma(ICP), X-ray diffraction(XRD), Scanning Electron Microscopy(SEM), and Dielectric Thermal Analyzer(DETA). Also, the Von-Mises stress of the top part of bushing was determined by using ANSYS program. The Von-Mises stress of the newly designed bushing was reduced about 50%. Therefore, if we apply the newly designed bushing, the number of mechanical breakdown may be decreased.

• Proceedings of the KIPE Conference
• /
• 2012.11a
• /
• pp.93-94
• /
• 2012

본 논문에서는 효율 향상과 부피저감을 위한 전기자동차용 3.7kW급 비절연형 탑재형 충전기를 소개하고, 강압영역에서의 성능 개선을 위한 알고리즘을 제안한다. 제안한 충전기 토폴로지는 Cascaded Buck-Boost 컨버터로 두개의 Pole로 구성되어 있으며, 강압영역에서 제어는 기존의 제어 방식과 다르게 두 개의 Pole을 동시에 제어하지 않고 각각을 제어하여 인덕터의 전류 리플을 저감하여 충전효율을 증가 시킬 수 있다. 제안한 시스템 및 알고리즘은 실험을 통해 검증한다.

• Carbon letters
• /
• v.1 no.2
• /
• pp.76-81
• /
• 2000

Physical properties of artificial graphite electrodes were evaluated along three different directions; circumferential (X), radial (Y), and axial (Z) directions. Four kinds of commercial electrode products were used in this study for the evaluation; pole (AP) and nipple (AN) of manufacturer A, pole (BP) and nipple (BN) of manufacturer B. The mechanical, electrical, and thermal properties in X and Y directions were very similar to each other. In Z direction, however, the mechanical properties, including flexural strength and compressive strength, were higher, and electric resistance and thermal expansion were much lower than those in the other directions. The microstructures observed by optical microscope and scanning electron microscope revealed that the differences in properties by the measuring direction were caused by the preferential alignment of needle cokes along the Z direction. When comparing the properties of the electrode samples in the same direction, the mechanical properties mainly depended on the bulk density or porosity of the samples as well as preferential alignment of needle cokes.

• Journal of electromagnetic engineering and science
• /
• v.1 no.1
• /
• pp.83-87
• /
• 2001

Many communication systems require bandpass filters with sharp skirt frequency characteristics in order to avoid the interferencce, which results in more order in the filter design. However, because of the limited Q values bandpass filters made of small sized ceramic resonators suffer from relatively large ripples at the band edges as the order of the filter increases. In order to compensate the large ripples while maintaining the sharp skirt frequency we propose a new RF amplitude equalizer. The equalizer made of two pole bandpass filter and an amplifier whose amplitude characteristics are the reverse of those of the bandapss filter. At the cellular band 9-pole bandpass filter with 10 MHz bandwidth exhibits 3 dB ripple when 8mm*8mm ceramic coaxial resonators are used. We added the RF equalizer to this filter and the flatness is improved as less than 1 dB.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.10
• /
• pp.1923-1929
• /
• 2009

The design of SPMSM(surface mounted permanent magnet synchronous motor) has been performed to reduce cogging torque and torque ripples. In general, cogging torque and torque ripples are affected by the shapes of teeth width, yoke depth, magnet pole arc, etc. Particularly, the minimum design point of cogging torque and torque ripples are different so that the design of SPMSM should be done to compromise both of them for precision application. In this paper, the design of PMSM for EPS(electric power steering) system is performed to verify the validity, and the design characteristics versus teeth width, yoke depth, and magnet pole arc are investigated in order to find out the minimum point of cogging torque and torque ripples. In addition, skew of PM is applied for cogging torque reduction.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.387-390
• /
• 2000

The life of transformer is significantly dependent on the thermal behavior in windings. To analyse winding temperature rise, many transformer designer have calculated temperature distribution and hot spot point by finite element method(FEM). Recently, numerical analyses of transformer are studied for optimum design, that is electric field analysis, magnetic field, potential vibration, thermal distribution and thermal stress. Therefore design time and design cost are decreased by numerical analysis. In this paper, the temperature distribution and thermal stress analysis of 50kVA pole cast resin transformer for power distribution are investigated by FEM program. The temperature change according to load rates of transformer also have been investigated. We have carried out temperature rise test and test results are compared with simulation data.