• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.81-84
• /
• 2001

In industrial field, especially the mobile generator is almost used as a islanding generator source for light, electric thrill, and compressor, and so on. However, because there still exists a lot of aged load, it causes the electric shock against person. In this paper authors introduce the proper method to reduce the electric shock in field discussing the scheme of ground connection.

• Design & Manufacturing
• /
• v.9 no.2
• /
• pp.1-5
• /
• 2015

Recently, as small-sized display products such as mobile phones and digital cameras have become lighter and smaller, the size of electric signal delivery part, connector for the mobile display products, also, needs to become smaller, so high-density integration like shortening the distance between signal delivery media, conductors is necessary. With the micro and high-density integration of the connector, it is necessary to maintain contact to a certain degree for keeping intensity and delivering electric signal smoothly to prevent a defect with a specific impact. Accordingly, this study carried out a structural analysis according to the operating mechanisms of 0.16CHP Class Bottom Contact FPC Connector and 0.24CHP Class BTB Connector mostly used in small-sized mobile display products such as mobile phones and digital cameras. As a result of the analysis, both connectors had lower than 997MPa, yield strength of connector material C5240-XSH, so it is judged that permanent plastic deformation would not occur, and that a contact force between the connector and FPC film occurs to a certain degree, so that there would not be any defect in electric signal delivery.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.669-674
• /
• 2017

Due to the depletion of fossil fuels and the increase in environmental pollution, electric vehicles are attracting attention as next-generation transportation and are becoming popular all over the world. As the interest in electric vehicles and the penetration rate increase, studies on the charging infrastructure with vehicle-to-grid (V2G) technology and information technology are actively under way. In particular, communication with the grid network is the most important factor for stable charging and load management of electric vehicles. However, with the existing centralized infrastructure, there are problems when control-message requests increase and the charging infrastructure cannot efficiently operate due to slow response speed. In this paper, we propose a new charging infrastructure using mobile edge computing (MEC) that mitigates congestion and provides low latency by applying distributed cloud computing technology to wireless base stations. Through a performance evaluation, we confirm that the proposed charging infrastructure (with low latency) can cope with peak conditions more efficiently than the existing charging infrastructure.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.4
• /
• pp.833-838
• /
• 2005

In this paper, we propose SAR(Specific absorption rate) reduction methods based on surface electric field distribution relation for mobile handsets. Proposed the new method that is able to consider improvement of the SAR from the very beginning step of developing the mobile handsets. Analysis of mobile handset with human body(head) using finite element method(FEM). Results of this method, SAR reduced about $50\;\%$.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.694-699
• /
• 1989

This paper presents a technique for an autonomous mobile robot to locate its own position in a visual way. The developed mobile robot perceives its surroundings through an equipped TV camera and acquires the visual information necessary for its next behavior. The robot which is assumed to move in a laboratory environment identifies its position by recognizing three different marks in the environment and analyzing the positional relation between these marks and itself. This technique was examined by an experiment and a satisfactory result was obtained.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3608-3613
• /
• 2009

In this paper, we propose a mobile Radio Frequency Identification antenna for mobile hand set. The proposed antenna with directive radiation characteristics based on combination of electric-magnetic radiators can be installed in the mobile hand-set. The combination of PIFA antenna for electric radiator and loop antenna for magnetic radiator is presented and designed for료 m-RFID reader system. Target frequency band is 900-MHz band. and desired gain is 4dBi. The antenna is simulated using Ansoft HFSS software and shows expected results. The antenna is also manufactured using FR4-epoxy circuit board (h=1 mm, $\varepsilon_{\tau}=4.4$). There are good agreements between the simulated and measured VSWR curves and radiation characteristics.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.1
• /
• pp.58-67
• /
• 2013

In this paper, a mobile relay station(MRS) for vehicles with a beamforming antenna is considered to increase the reliability of a transmission link, especially for the MRS at cell boundary. Cell searching and direction-of-arrival(DoA) estimation methods for an MRS with a uniform linear array(ULA) are proposed for a multipath environment in OFDM-based cellular systems. Performances of the proposed methods(Method1 and Method2) are evaluated by computer simulation with the standard profile of IEEE 802.16e.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.597-599
• /
• 2005

To make the autonomous mobile robot move in the unknown space, we have to know the information of current location of the robot. So far, the location information that was obtained using Encoder always includes Dead Reckoning Error, which is accumulated continuously and gets bigger as the distance of movement increases. In this paper, we analyse the effect of the size of the two wheels of the mobile robot and the wheel track of them among the factors of Dead Reckoning Error. And after this, we compensate this Dead Reckoning Error by Kalman filter using Gyro Sensors. To accomplish this, we develop the controller to analyse the error components of Gyro Sensor and to minimize the error values. We employ the numerical approach to analyse the error components by linearizing them because each error component is nonlinear. And we compare the improved result through simulation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.12
• /
• pp.1003-1006
• /
• 2017

In this paper, during radio-frequency performance testing in a shield box, the non-uniform electric field distribution between multiple mobile phones is examined by numerical simulation, and two ways to improve the field uniformity among mobile phones under test are proposed. The results demonstrate that the proposed methods can greatly improve the field uniformity.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2374-2376
• /
• 2001

In this paper we have developed a Power Line Proximity Detecting device for Mobile Crane by using a Derivation Electric-Potential Detection method. A mobile crane worker can be easily exposed to a dangerous electrical shock and the electrocution while they are working at near the high-voltage electrical lines. The derivation electric-potential of the power lines have been simulated in our experiment, Also, microprocessor-based detecting device and transmitter/receiver modules are introduced to show a solution for the dangerous mobile crane working environment. As a result, It has been shown a good functional field test.