• KIEAE Journal
• /
• 제9권2호
• /
• pp.99-106
• /
• 2009

The noise in apartment buildings are major factor that determine the quality of indoor noise environment. Particularly, the noise from children's running footsteps and plumbing noise have caused the residents who live in decrepit apartment houses to uncomfortable environment. And as time go by, sound performance are getting worse according to the aging of the facilities. So this study deals with the plans to improve the sound performance of decrepit apartment house. To compare the noise reduction, we measured the heavy-weight impact sound level and plumbing noise level before and after changes the measurement conditions. As the results of measurements, the heavy-weight impact sound level were decreased when stiffness reinforcement were installed on slab. Especially the sound level were decreased 2.1-7.6dB in 50-80Hz of low frequency range. Instead of PVC pipe system, cast iron pipe and triple elbow drain pipe systems were installed. Noise level were decreased 15dB(A) in 250Hz. Noise level of pipe system's on the slab is less than under slab one. On the contrary water saving stool showed increasing the noise level.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권8호
• /
• pp.849-855
• /
• 2015

A better flow condition for the intake of pump is provided by the sump pump that connects the forebay to the intake of the pump station. If the suction sump is improperly shaped or sized, air-entraining vortices or submerged vortices may develop. These phenomena may greatly affect pump operation if vortices become sufficiently large. Moreover, any remaining vortices in the pump flow passage may result in an increase in the noise and vibration of the pump. Therefore, the vortices in the pump flow passage must be reduced to achieve good pump sump station performance. In this study, the effect of suction pipe leaning angle on the pump sump's internal flow is investigated. Additionally, a pipe type with an elbow shape is investigated. The results show that the air entraining vortices occur under the condition of a water level ratio H/D = 1.31 for each suction pipe type.

• 한국안전학회지
• /
• 제33권5호
• /
• pp.164-169
• /
• 2018

A detailed fatigue evaluation procedure was developed to mitigate the excessive conservativeness of the conventional environmental fatigue evaluation method for the pressurizer spray line elbow of domestic new nuclear power plants. The pressurizer spray line is made of austenitic stainless steel, which is relatively sensitive to the environmentally assisted fatigue, and has a low degree of design margin in terms of environmentally assisted fatigue due to the thermal stratification phenomenon on the pipe cross section as a whole or locally. In this study, to meet the environmental fatigue design requirements of the pressurizer spray line elbow, the new environmental fatigue evaluation has been performed, which used the ASME Code NB-3200-based detailed fatigue analysis and the environmental fatigue correction factor instead of the existing NB-3600 evaluation method. As a result, the design requirements for environmentally assisted fatigue were met in all parts of the pressurizer spray line elbow including the fatigue weakened zones by thermal stratification.

• 설비공학논문집
• /
• 제16권2호
• /
• pp.142-149
• /
• 2004

Recently, the government introduced the thermal storage system for reducing the electric power load. Especially, the ice slurry type has gained lots of interest due to its good heat transfer and flowing characteristics. This study was peformed to understand the effects of transporting ice slurry through elbows of various angle. Propylene glycol water solution was used and about 2 mm ice particles were circulated. The experiments were carried out under various conditions, such as concentration and velocity of water solution ranging between 0∼20 wt％, 1.5∼2.5 m/s, respectively. And elbows with 4 different angles of 30$^{\circ}$, 45$^{\circ}$, 90$^{\circ}$, 180$^{\circ}$. The differential pressure and IPF (ice packing factor) between the pipe entry and exit were measured. The tendency of pressure loss and outlet IPF in elbow is that the pressure loss was reduced as concentration and flow velocity of water solution is increased, and low value appeared at 10 wt％ and 2.5 m/s. The variation of outlet IPF was compared with the inlet IPF in the range of $\pm$20％.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.165-171
• /
• 2000

The study about a drainpipe of water closet was performed as reduction plan on drainage noise for water closet, which of noise in plumbing systems was being indicated the major point at issue in apartment houses. A drainpipe of water closet is divided into a sleeve, a joint elbow and a traversing pipe, through the result of experiment, for an effective noise reduction in a drainpipe a threefold joint elbow is proposed among parts. And through the experiment of performance with glasswool, the removal of glasswool should be in the economical efficiency aspect.

• 한국산학기술학회논문지
• /
• 제9권2호
• /
• pp.480-486
• /
• 2008

유한요소 해석을 수행하여 엘보우의 거동을 파악하였으며 해석 시 엘보우의 휨 각도와 엘보우계수를 주요변수로 사용하였다. 사용하중은 엘보우 축이 형성하는 평면 내에 작용하는 휨 모멘트를 사용하였으며 해석 결과를 이론적 정해 법으로 유도된 ASME 코드 식과 비교하였다. 또한 엘보우 단면의 응력상태와 유연도 특성을 이용하여 엘보우 단면의 타원변형으로 인한 엘보우의 기하학적 비선형 특성을 설명하였다.

• Nuclear Engineering and Technology
• /
• 제55권5호
• /
• pp.1616-1629
• /
• 2023

To quantify the conservatism of existing ASME strain-based evaluation methods for seismic loading, this paper presents very low cycle fatigue test data of elbows under various cyclic loading conditions and comparison of evaluation results with experimental failure cycles. For strain-based evaluation methods, the method presented in ASME BPVC CC N-900 and Sec. VIII are used. Predicted failure cycles are compared with experimental failure cycle to quantify the conservatism of evaluation methods. All methods give very conservative failure cycles. The CC N-900 method is the most conservative and prediction results are only ~0.5% of experimental data. For Sec. VIII method, the use of the option using code tensile properties gives ~3% of experimental data, and the use of the material-specific reduction of area can reduce conservatism but still gives ~15% of experimental data.

• International Journal of Fluid Machinery and Systems
• /
• 제10권2호
• /
• pp.138-145
• /
• 2017

The problem of non-uniform inflow exists in many practical engineering applications, such as the elbow suction pipe of waterjet pump and, the channel head of steam generator which is directly connect with reactor coolant pump. Generally, pumps are identical designs and are selected based on performance under uniform inflow with the straight pipe, but actually non-uniform suction flow is induced by upstream equipment. In this paper, CFD approach was employed to analyze unsteady hydrodynamic characteristics of reactor coolant pumps with different inflows. The Reynolds-averaged Naiver-Stokes equations with the $k-{\varepsilon}$ turbulence model were solved by the computational fluid dynamics software CFX to conduct the steady and unsteady numerical simulation. The numerical results of the straight pipe and channel head were validated with experimental data for the heads at different flow coefficients. In the nominal flow rate, the head of the pump with the channel head decreases by 1.19% when compared to the straight pipe. The complicated structure of channel head induces the inlet flow non-uniform. The non-uniformity of the inflow induces the difference of vorticity distribution at the outlet of the pump. The variation law of blade to blade velocity at different flow rate and the difference of blade to blade velocity with different inflow are researched. The effects of non-uniform inflow on radial forces are absolutely different from the uniform inflow. For the radial forces at the frequency $f_R$, the corresponding amplitude of channel head are higher than the straight pipe at $1.0{\Phi}_d$ and $1.2{\Phi}_d$ flow rates, and the corresponding amplitude of channel head are lower than the straight pipe at $0.8{\Phi}_d$ flow rates.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권6호
• /
• pp.816-824
• /
• 2010

본 논문에서는 쓰레기 이송관로내의 물체에 작용하는 힘을 분석하고 그 물체의 운동방정식 확립하였다. 그 운동방정식은 1계 비선형 미분방정식이 되며 이것의 일반해를 이용하면 쓰레기 이송관로내 물체의 속도를 구할 수가 있다. 물체의 속도는 엘보우와 같은 쓰레기 이송관로의 곡선부에서 내벽의 충돌속도가 되므로 충돌시 물체의 운동에너지를 계산할 수 있고, 따라서 필요한 내벽의 충격강도를 알 수가 있다. 하나의 예로써 쓰레기 이송관로내 공기의 속도가 30m/sec일 때 물체의 속도를 계산하여 그래프로써 나타내었으며, 이것으로부터 물체가 내벽에 충돌할 때의 운동에너지를 계산할 수 있도록 하였다. 또한 용융주조 현무암 튜브를 철강파이프 내면에 보호벽으로 씌운 복합재료 파이프에 추를 자유낙하시켜 충격을 주는 방식으로 충격시험을 한 결과를 제시하였으며, 그 결과에 의하면 용융 주조 현무암 튜브는 쓰레기 이송관로의 내면 보호벽으로 충분한 충격강도를 가지는 것이 판명되었다.

• 한국소음진동공학회논문집
• /
• 제27권1호
• /
• pp.114-120
• /
• 2017

Water supply and drainage noise in the bathroom is recognized as one of the main noises, along with the floor-impact sounds, in apartment housings. Recently, to solve such noise issues, a new construction method of installing the piping on the slab has been adopted. rather than the traditional method of penetrating the piping through the slab between the upper and the lower bathrooms. However, this new method has limitations due to high costs and constructional difficulties. Therefore, this study was conducted to develop noise reducing piping and elbows, where the noise can be reduced simply by replacing the existing pipings. The noise level was measured in a laboratory by installing the horizontal drainage piping (three types) and the elbows (three types) developed in this study. The results showed that the horizontal pipings reduced the noise level in LAmax by 0.3 dB(A)~1.0 dB(A), as compared to the existing pipings (VG2), indicating an insignificant noise reduction effect. The elbow reduced the noise level in LAmax by 5.5 dB(A) ~ 11.5 dB(A), as compared to the existing elbow (DRF elbow), with the result of reducing the noise level at all frequencies evenly. Consequently, it was shown that using the elbows is more effective in reducing the water-drainage noise from the toilet than using the horizontal pipings.