• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.11
• /
• pp.910-917
• /
• 2003

Fluid flow in a rectangular duct for 90$^{\circ}$ bend elbow with the ratio of 1.5 between its curvature radius and width is measured by 5 W laser doppler velocity meter. The fluid flow is also computed by commercial software of STAR-CD for comparison between measured and computed velocity profiles in the duct. Reynolds numbers for the comparison are 11,643, 19,746 and 24,260. From the comparison, computation of principal velocity components in the duct predicts the experimental data somewhat satisfactorily even though those of minor velocity components and turbulent kinetic energy do not match with the experimental data quite well. K-factor for the bend elbow is computed to be average 0.086 while the equivalent ASHRAE data is 0.07.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.11a
• /
• pp.3-7
• /
• 2001

Although elbows are commonly used in practice, many questions regarding the optimum arrangement still remain unanswered. The effect due to an elbow lasts for a considerable distance downstream of the elbow and is severe when two elbows are in the system. The goal of this study is to provide an effective guide for the optimum arrangement of elbows and the optimum design of the approach piping system.

• Fashion & Textile Research Journal
• /
• v.11 no.1
• /
• pp.130-139
• /
• 2009

This study was conducted to reproduce the Leg of Mutton Sleeve pattern of the ladies' costume of the 1890's for Korean women of the twenties who have the standard body type and the average size. Nineteen Leg of Mutton Sleeve patterns of the ladies' costume of the 1890's were collected and drawn to actual size. Nineteen Leg of Mutton Sleeve patterns of the ladies' costume of the 1890's were classified into three groups(S1~S3) by the pattern pieces and the bend of the lower part of the elbow line. The S1 was one-piece sleeve pattern and the lower part of the elbow line of S1 was not bent. The gathers volume of sleeve cap of S1 was smaller than S2 and S3. The S2 was one-piece sleeve pattern and the lower part of the elbow line of S2 was bent. The S2 pattern had typical characteristics of the Leg of Mutton Sleeve that the gathers volume of sleeve cap was large and the lower part of elbow line was tight. The S3 was two-piece sleeve pattern and the lower part of the elbow line of S3 was bent. The gathers volume of sleeve cap of S3 was similar with S2. The study patterns of three groups of the Leg of Mutton Sleeve which had the characteristics and the silhouette of the Leg of Mutton Sleeve pattern of the ladies' costume of the 1890's were designed like for Korean women of the twenties who have the standard body type and the average size through modifications based on the evaluation of dressing on two occasions. The study pattern of three groups of the Leg of Mutton Sleeve were evaluated to have the silhouette of the Leg of Mutton Sleeve of the 1890's and to fit Korean women of the twenties who have the standard body type and the average size with the sensory test.

• Journal of the Korean Society of Safety
• /
• v.18 no.4
• /
• pp.28-34
• /
• 2003

In the present study, three-dimensional finite element analysis was performed to investigate the effects of internal wall thinning defect on the failure pressure of elbow in the piping system and to develop the failure pressure evaluation model. From the results of finite element analysis, the failure pressure was derived by employing local stress criteria, and the effects of thinning location, bend radius, and defect geometry on the failure pressure of internally wall thinned elbow were investigated. Also, based on these investigations and previous model developed to estimate the failure pressure of elbow with an external pitting defect, the failure pressure evaluation model to be applicable to the elbow containing an internal thinning defect was proposed and compared with the results of finite element analysis. The failure pressure calculated by the model agreed well with the results of finite element analysis.

• Journal of the Korean Society of Safety
• /
• v.20 no.1 s.69
• /
• pp.55-61
• /
• 2005

The purpose of this study is to investigate the effect of circumferential location of local wall thinning defect on the collapse behavior of an elbow. Thus, the present study conducts three-dimensional finite element analysis on the 90-degree elbow containing a local wall thinning at intrados, crown and extrados of bend region and evaluates the collapse moment of wall thinned elbow under various thinning shapes and loading conditions. Combined internal pressure and bending moment are considered as an applied load. The internal pressure of $0\~20MPa$ and both closing and opening mode bending are employed. The results of analysis show that the reduction in collapse moment of the elbow by local wall thinning is more significant for a defect locating at crown than for a defect locating at intrados or at extrados. Also, the effect of internal pressure on the collapse moment of wall thinned elbow depends on the circumferential location of thinning defect and applied bending mode.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.7 s.238
• /
• pp.947-954
• /
• 2005

The purpose of this study is to develop failure pressure evaluation models, which are applicable to straight pipes and elbows containing an internally wall thinning defect induced by flow-accelerated-corrosion (FAC). In this study, thus, three dimensional finite element (FE) analyses are performed to investigate the dependences of failure pressure of internally wall thinned pipe on the defect shape, the pipe geometry, and the defect location and bend radius of elbow. Also, the existing failure pressure assessment models for externally wall thinned pipes are examined. Based on these, the new models for assessing failure pressure of piping components with an internally wall thinning defect are proposed. Comparison of failure pressure, predicted by proposed models, with FE analysis result shows good agreement regardless of pipe type, defect shape, and defect location and bend radius.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.2
• /
• pp.480-486
• /
• 2008

The pipe elbows subjected to in-plane bending moments are analyzed with the finite element method. The results from the finite element analysis are compared with ASME code equations that are theoretical closed form solutions. The geometric nonlinear effects due to the ovalization are explained with the magnitude and the types of the stresses and the flexibilities of the elbows with the emphasis on the bend angles and elbow factors.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.12
• /
• pp.5177-5183
• /
• 2010

The effects of the ovalization of the tangential pipes to the elbows are analyzed. The geometric nonlinear behaviors of the elbows are shown with the element capable of ovalization. The relationships between the length of the tangential pipes in the models and the bend angles of the elbows are analyzed to supplement the ASME code. And the proper length of the tangential pipes for the elbow models are suggested.

• Journal of Fashion Business
• /
• v.18 no.4
• /
• pp.1-14
• /
• 2014

Currently smart textile market is rapidly expanding and the demand is increasing integration of an electronic fiber circuit. The garments are an attractive platform for wearable device. This is one of the integration techniques, which consists of is the selective introduction of conductive yarns into the fabric through knitting, weaving or embroidering. The aim of this work is to develop a golf bend driven prototype design for an attachable Arduino that can be used to assess elbow motion. The process begins with the development of a wearable device technique that uses conductive yarn and flex sensor for measurement of elbow bending movements. Also this paper describes and discusses resistance value of zigzag embroidery of the conductive yarns on the tensile properties of the fabrics. Furthermore, by forming a circuit using an Arduino and flex sensor the prototype was created with an assistance band for golf posture training. This study provides valuable information to those interested in the future directions of the smart fashion industry.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1766-1771
• /
• 2007

This paper presents plastic limit loads and approximate J-integral estimates for circumferential part-through surface crack at the interface between elbows and pipes. Based on finite element limit analyses using elastic-perfectly plastic materials, plastic limit moments under in-plane bending are obtained and it is found that they are similar those for circumferential part-through surface cracks in the center of elbow. Based on present FE results, closed-form limit load solutions are proposed. Welds are not explicitly considered and all materials are assumed to be homogeneous. And the method to estimate the elastic-plastic J-integral for circumferential part-through surface cracks at the interface between elbows and straight pipes is proposed based on the reference stress approach, which was compared with corresponding solutions for straight pipes.