• 대한기계학회논문집A
• /
• 제29권6호
• /
• pp.876-888
• /
• 2005

Tensile properties and fracture toughness of monolithic aluminum, fiber reinforced plastics and glass fiber/aluminum hybrid laminates under tensile loads have been investigated using plain coupon and single-edge-notched specimens. Elastic modulus and ultimate tensile strength of GFMLs showed different characteristic behaviors according to the Al kind, fiber orientation and composition ratio. Fracture, toughness of A-GFML-UD which was determined by the evaluation of $K_{IC}$ and $G_{IC}$ based on critical load was similar to that of GFRP-UD and was much higher than monolithic Al. Therefore, A-GFML-UD presented superior fracture toughness as well as prominent damage tolerance in comparison to its constituent Al. By separating Al sheet from GFMLs after the test, optical microscope observation of fracture zone of GFRP layer in the vicinity of crack tip revealed that crack advance of GFMLs depended on the orientation of fiber layer as well as Al/fiber composition ratio.

• 대한기계학회논문집A
• /
• 제25권2호
• /
• pp.220-227
• /
• 2001

The fatigue crack initiation life is studied on automotive tensile-shear spot weldment made from cold rolled carbon steel(SPC) sheet by using DCPDM and local strain approach. It can be found that the fatigue crack initiation behavior in spot weldment can be definitely detected by DCPDM system. To predict the fatigue life of spot weldment, the local stresses and strains at the potential critical region are estimated by approximate method based on Neubers rule and elastic-plastic FEM analysis. A satisfactory correlation between the predicted life obtained from Local strain approach based on Neubers rule and experimental life can be found in spot weldment within a factor of 2.

• 한국농공학회논문집
• /
• 제48권1호
• /
• pp.61-68
• /
• 2006

The p-version nonlinear finite element model has been developed to analyze the nonlinear behavior of simply supported RC slabs strengthened with carbon fiber reinforced plastic sheets. The shape function is adopted with integral of Legendre polynomials. The compression model of concrete is based on the Kupfer's yield criterion, hardening rule, and crushing condition. The cracking behavior is modeled by a smeared crack model. In this study, the fixed crack approach is adopted as being geometrically fixed in direction once generated. Each steel layer has a uniaxial behavior resisting only the axial force in the bar direction. Identical behavior is assumed fur tension and compression of steel according to the elastic modulus. The carbon fiber reinforced plastic sheets are considered as reinforced layers of equivalent thickness with uniaxial strength and rigidity properties in the present model. It is shown that the proposed model is able to adequately predicte the displacement and ultimate load of nonlinear simply supported RC slabs by a patch with respect to reinforcement ratio, thickness and angles of CFRP sheets.

• Steel and Composite Structures
• /
• 제20권1호
• /
• pp.147-166
• /
• 2016

The paper presents comprehensive quasi-static stability analysis results for a real funnel-flow cylindrical steel silo composed of horizontally corrugated sheets strengthened by vertical thin-walled column profiles. Linear buckling and non-linear analyses with geometric and material non-linearity were carried out with a perfect and an imperfect silo by taking into account axisymmetric and non-axisymmetric loads imposed by a bulk solid following Eurocode 1. Finite element simulations were carried out with 3 different numerical models (single column on the elastic foundation, 3D silo model with the equivalent orthotropic shell and full 3D silo model with shell elements). Initial imperfections in the form of a first eigen-mode for different wall loads and from 'in-situ' measurements with horizontal different amplitudes were taken into account. The results were compared with Eurocode 3. Some recommendations for the silo dimensioning were elaborated.

• Structural Engineering and Mechanics
• /
• 제31권4호
• /
• pp.439-451
• /
• 2009

The paper deals with the problem related to the modelling of riveted assemblies for crashworthiness analysis of full-scale complete aircraft structures. Comparisons between experiments and standard FE computations on high-energy accidental situations onto aluminium riveted panels show that macroscopic plastic strains are not sufficiently localised in the FE shells connected to rivet elements. The main reason is related to the structural embrittlement caused by holes, which are currently not modelled. Consequently, standard displacement FE models do not succeed in initialising and propagating the rupture in sheet metal plates and along rivet rows as observed in the experiments. However, the literature survey show that it is possible to formulate super-elements featuring defects that both give accurate singular strain fields and are compatible with standard displacement finite elements. These super-elements can be related to the displacement model of the hybrid-Trefftz principle of the finite element method, which is a kind of domain decomposition method. A feature of hybrid-Trefftz finite elements is that they are mainly used for elastic computations. It is thus proposed to investigate the possibility of formulating a hybrid displacement finite element, including the effects of a hole, dedicated to crashworthiness analysis of full-scale aeronautic structures.

• Computers and Concrete
• /
• 제23권5호
• /
• pp.361-376
• /
• 2019

In this research, bending analysis of a micro sandwich skew plate with isotropic core and piezoelectric composite face sheets reinforced by carbon nanotube on the elastic foundations are studied. The classical plate theory (CPT) are used to model micro sandwich skew plate and to apply size dependent effects based on modified strain gradient theory. Eshelby-Mori-Tanaka approach is considered for the effective mechanical properties of the nanocomposite face sheets. The governing equations of equilibrium are derived using minimum principle of total potential energy and then solved by extended Kantorovich method (EKM). The effects of width to thickness ratio and length to width of the sandwich plate, core-to-face sheet thickness ratio, the material length scale parameters, volume fraction of CNT, the angle of skew plate, different boundary conditions and types of cores on the deflection of micro sandwich skew plate are investigated. One of the most important results is the reduction of the deflection by increasing the angle of the micro sandwich skew plate and decreasing the deflection by decreasing the thickness of the structural core. The results of this research can be used in modern construction in the form of reinforced slabs or stiffened plates and also used in construction of bridges, the wing of airplane.

• Design & Manufacturing
• /
• 제16권4호
• /
• pp.40-45
• /
• 2022

The EV electric vehicle market is growing rapidly worldwide. An electric vehicle means a vehicle that uses energy charged through an electricity source as power. The precision of the press is important to mass-produce the drive motor, which is a key component of the electric vehicle. The size of the driving motor is increasing, and The size of the mold is also growing. In this study, the precision of large high-speed presses for mass production of driving motors was measured. A study was conducted on the measurement method of press and the analysis of measurement data. A drive motor is a component that transmits power by converting electrical energy into kinetic energy. EV driven motors have key material properties to improve efficiency. The material properties are the thickness of the material. As a method for improving performance, use a 0.2mm thin steel sheet. Mold is also becoming larger. As the mold grows, the size of the high-speed press for mass production of the driving motor is also increasing. Also, the precision of the press is the most important because it uses a thin iron plate material. So the importance of large press precision is being emphasized. In this study, the effect of large high-speed press structure on precision was verified

• Steel and Composite Structures
• /
• 제49권1호
• /
• pp.19-30
• /
• 2023

Steel-concrete composite slabs represent a very efficient floor solution combining the key performance of two different materials: the steel and the concrete. Composite slab response is governed by the degree of the interaction between these two materials, mainly depending by chemical and mechanical bond. The latter is characterized by a limited degree of confinement if compared with the one of the rebars in reinforced concrete members while the former is remarkably influenced by the type of concrete and the roughness of the profiled surface, frequently lubricated during the cold-forming manufacturing processes. Indeed, owing to the impossibility to guarantee a full interaction between the two materials, a key parameter governing slab design is represented by the horizontal shear-bond strength, which should be always experimentally estimated. According to EC4, the design of the slab bending resistance, is based on the simplified assumption that the decking sheet is totally yielded, i.e., always in plastic range, despite experimental and numerical researches demonstrate that a large part of the steel deck resists in elastic range when longitudinal shear collapse is achieved. In the paper, the limit strain for composite slab, which corresponds to the slip, i.e., the debonding between the two materials, has been appraised by means of a refined numerical method used for the simulation of experimental results obtained on 8 different composite slab types. In total, 71 specimens have been considered, differing for the properties of the materials, cross-section of the trapezoidal profiled metal sheets and specimen lengths.

• 한국구조물진단유지관리공학회 논문집
• /
• 제22권4호
• /
• pp.100-107
• /
• 2018

본 연구의 목적은 철근콘크리트 휨 부재에 탄소섬유시트, 유리섬유시트, PET(polyethylene terephthalate) 섬유 등을 이용하여 보강했을 때, 보강재 종류, 보강재 물성, 보강량 등에 따른 보강효과를 파악하는 것이다. 변수별 보강효과를 파악하기 위해 가상의 휨부재를 기준실험체로 선정하여, 기준실험체에 대해 항복단면과 극한단면일 때의 모멘트-곡률 관계를 파악하였다. 보강하지 않은 기준실험체에 보강재 종류, 보강재 물성, 보강량 등 다양한 변수를 적용하여 총 11개의 실험체의 모멘트-곡률 곡선을 비교하였다. 분석 결과, 보강하지 않은 실험체에 비해 보강한 실험체의 휨강도는 높게 나타났다. 그러나 연성에 대해서는 보강하지 않은 기준실험체가 가장 우수한 것으로 나타났다. 변수별 휨 보강효과는 보강량이 많고, 파괴시 재료강도가 높을수록 우수하게 나타났으며, 연성효과는 보강재의 파괴시 변형률이 높을수록 우수한 것으로 나타났다. 손상 전과 손상 후의 보강효과에 대해서는 휨보강 효과와 연성효과 모두 10% 이내로 미미하게 나타나 손상상태에 있더라도 온전한 상태로 해석해도 큰 차이가 없을 것으로 판단된다.

• 한국의류학회지
• /
• 제23권4호
• /
• pp.499-509
• /
• 1999

This study was carried out to investigate the effects of wearing disposable diaper with the endothermic agent on thermoregulatory response of infant. Five healthy female infants aged about 5 months were taken as a subject of this experiment. Experimental diapers were six kinds of disposable diaper constructed of nonwoven tissue, fluff pulp, super absorbent polymer, back sheet film, leg elastic, and 0g urea(A) 1g urea(B) , 2g urea(C), 3g urea (D), 4g urea(E) 5g, urea(F) respectively. Urea(98% or over purity) was used as an endothermic agent. Experiment was proceeded while infants were sleeping at 27.5$\pm$0.5$^{\circ}C$, 50$\pm$5% R.H, 0.04m/sec. Each disposable diaper's properties was tested. During the experiment rectal temperature skin temperature of 9 areas temperature inside the disposable diapers were measured, the results were as follows : 1) There was not significant difference among the diapers in absorption capacity retention capacity and rewet(p=0.05). The absorption under load was showed to A, B,