• 한국방재학회 논문집
• /
• 제1권1호
• /
• pp.81-90
• /
• 2001

2경간 연속 철도교의 종방향 거동에 영향을 미치는 여러 인자들에 대해서 연구하였다. 그 인자들로는 교각 강성의 크기, 교각의 높이, 교각기초의 크기와 교각받침의 강성을 변화시켜 그에 따른 변화양상을 살펴보았다. 그 결과 고정단 교각에서의 여러 인자들의 변화에 따른 종방향 거동의 변화가 가동단 교각에서의 변화에 따른 영향보다 크다는 사실을 확인할 수 있었다. 또한, 받침강성을 변화시켜서 종방향 거동을 제어하는 것이 다른 인자들을 변화시키는 것보다 더 경제적이라 할 수 있다.

• 한국강구조학회 논문집
• /
• 제10권1호통권34호
• /
• pp.63-72
• /
• 1998

강구조물의 강성설계법을 실용적인 변위조절법인 구조물량재분배기법과 강도설계법을 결합하여 개발하였다. 본 연구에 사용된 재분배기법은 최적화기법에 의하여 유도되었으며, 최적화문제의 에너지이론에 근거한 부재변위기여도를 이용하여 정식화되었다. 이러한 재분배기법에 의한 변위조절은 설계민감도계수의 계산 그리고 구조재해석을 필요로 하지 않는 특성을 가지고 있다. 변위조절을 위한 구조물량의 재분배에 의한 부재응력의 재분배 효과는 허용응력설계법에 준한 강도설계모듈에 의하여 조절되었다. 개발된 강성설계법을 3차원 트러스 구조물의 설계에 적용하였다.

• Structural Monitoring and Maintenance
• /
• 제5권4호
• /
• pp.489-506
• /
• 2018

This paper reported test of full-scale cables attached with four types of dampers: viscous damper, passive Magneto-Rheological (MR) damper, friction damper and High Damping Rubber (HDR) damper. The logarithmic decrements of the cable with attached dampers were calculated from free vibration time history. The efficiency ratios of the mean damping ratios of the tested four dampers to theoretical maximum damping ratio were derived, which was very important for practical damper design and parameter optimization. Non-ideal factors affecting damper performance were discussed based on the test results. The effects of concentrated mass and negative stiffness were discussed in detail and compared theoretically. Approximate formulations were derived and verified using numerical solutions. The critical values for non-dimensional concentrated mass coefficient and negative stiffness were identified. Efficiency ratios were approximately 0.6, 0.6, and 0.3 for the viscous damper, passive MR damper and HDR damper, respectively. The efficiency ratio for the friction damper was between 0-1.0. The effects of concentrated mass and negative stiffness on cable damping were positive as both could increase damping ratio; the concentrated mass was more effective than negative stiffness for higher vibration modes.

• Earthquakes and Structures
• /
• 제16권1호
• /
• pp.119-127
• /
• 2019

When a structural wall is subjected to multi-directional ground motion, torsion-induced cracks degrade the stiffness of the wall. The effect of torsion should not be neglected. As a main lateral load resisting member, reinforced concrete (RC) structural wall has been widely studied under the combined action of bending and shear. Unfortunately, its seismic behavior under a combined action of torsion, bending and shear is rarely studied. In this study, torsional performances of the RC structural walls under the combined action is assessed from a comprehensive parametrical study. Finite element (FE) models are built and calibrated by comparing with the available experimental data. The study is then carried out to find out the critical design parameter affecting the torsional stiffness of RC structural walls, including the axial load ratio, aspect ratio, leg-thickness ratio, eccentricity of lateral force, longitudinal reinforcement ratio and transverse reinforcement ratio. Besides, to facilitate the application in practice, an empirical equation is developed to estimate the torsional stiffness of RC rectangular structural walls conveniently, which is found to agree well with the numerical results of the developed FE models.

• 한국공간구조학회논문집
• /
• 제24권1호
• /
• pp.81-88
• /
• 2024

The purpose of this study is to experimentally analyze the seismic performance of beam-column specimens with vertical irregular, which were reinforced with RHS (Replaceable steel haunch system). a steel haunch system. To evaluate the seismic performance of the RHS, three specimens were manufactured and subjected to cycle loading tests. Retrofitted specimens have different beam-upper column stiffness ratio as a variable. The stiffness ratio of beam-upper column were considered to be 1.2 and 0.84. As a result of the test, the specimen reinforced with RHS showed improved maximum load and effective stiffness, and energy dissipation capacity compared to the non-retrofitted specimen with same beam-upper column stiffness ratio. The specimen with 0.84 beam-upper column stiffness ratio showed improved performance than the specimen with 12.

• 한국강구조학회 논문집
• /
• 제15권2호
• /
• pp.159-165
• /
• 2003

단부에 관통 가셋트판이 부착된 강관부재의 좌굴거동은 단부의 형상 및 상태에 따라 구속정도가 상이하게되며 단부요소는 세 장비에 따라 탄성 및 비탄성 거동 특성을 보임에 따라 이론적 좌굴내력을 도출하는 것은 사실상 불가능하다. 본 연구에서는 탄성좌굴의 이론적 접근을 바탕으로 세장비($\lambda$), 강성비($\beta$), 지지길이비(G), 강관크기, 부재의 초기변형 등을 고려하여 비탄성 유한요소 해석을 수행하여 각각의 영향요소가 좌굴하중에 미치는 영향을 살펴보았다. 또한 유한요소 모델링시 세장비($\lambda$), 강성비($\beta$), 지지길이비(G), 강관크기 등의 매개변수 분석을 통하여 강도식을 도출하였다.

• Computers and Concrete
• /
• 제9권2호
• /
• pp.133-151
• /
• 2012

This paper presents an analytical procedure for the analysis of high strength steel fiber reinforced concrete members considering the cracking effect in the serviceability loading range. Modifications to a previously proposed formula for the effective moment of inertia are presented. Shear deformation effect is also taken into account in the analysis, and the variation of shear stiffness in the cracked regions of members has been considered by reduced shear stiffness model. The effect of steel fibers on the behavior of reinforced concrete members have been investigated by the developed computer program based on the aforementioned procedure. The inclusion of steel fibers into high strength concrete beams and columns enhances the effective moment of inertia and consequently reduces the deflection reinforced concrete members. The contribution of the shear deformation to the total vertical deflection of the beams is found to be lower for beams with fibers than that of beams with no fibers. Verification of the proposed procedure has been confirmed from series of reinforced concrete beam and column tests available in the literature. The analytical procedure can provide an accurate and efficient prediction of deflections of high strength steel fiber reinforced concrete members due to cracking under service loads. This procedure also forms the basis for the three dimensional analysis of frames with steel fiber reinforced concrete members.

• Steel and Composite Structures
• /
• 제8권6호
• /
• pp.441-455
• /
• 2008

This paper presents an effective hysteretic model for the prediction and evaluation of steel reinforced concrete member seismic performance. This model adopts the load-deformation relationship acquired from monotonic load tests and incorporates the double-pivot behavior of composite members subjected to cyclic loads. Deterioration in member stiffness was accounted in the analytical model. The composite member performance assessment control parameters were calibrated from the test results. Comparisons between the cyclic load test results and analytical model validated the proposed method's effectiveness.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2002년도 춘계 학술발표회 논문집
• /
• pp.367-372
• /
• 2002

In these days, The base isolation system is often used to improve the seismic capacity of the structures instead of conventional techniques of strengthening the structural members. The purpose of this study is to evaluate dynamic properties and mechanical characteristics of the 10tonf-LRB(Lead-Rubber Bearing). Experimental studies were performed to obtain the hysteretic behavior, effective shear stiffness( $K_{eff}$), equivalent damping( $H_{eq}$ ), capacity of energy dissipation( $W_{D}$) of six 10tonf-LRB. Especially, in this study, the response of the LRB for high loading frequency(0.5Hz~3.0Hz) was estimated. The effective shear stiffness of the LRB decreases and the capacity of energy dissipation increases as the shear strain amplitude increases. But the shear behavior of the LRB is not affected sensitively by loading frequency.y.y.

• 제어로봇시스템학회논문지
• /
• 제7권11호
• /
• pp.927-932
• /
• 2001

When people write a character with a pen stably, proper compliance planning is necessary. In this paper, after investigating the property of character writing task, we propose a fundamental grasp model for character writing and also analyze compliance characteristics for effective character writing using multi-fingered hands. For this, the general stiffness relation of multi-fingered hand is firstly described. Next, we investigate the grasp configurations for grasping a pen and then, we analyze the conditions of the specified stiffness matrix in the operational space to successfully and more effectively achieve the given character writing task. Through the analysis, an effective grasp modeling for successful character writing is shown. And also, we conclude that the operational compliance characteristics should be properly planned for character writing, stably and precisely.