• Proceedings of the Korean Geotechical Society Conference
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.990-996
• /
• 2010

In this study, a method for estimating the effective stress of clays using in-situ penetration test(PCPT) result is proposed. The proposed method is based on a correlation between the PCPT results and strength increment ratio. According to proposed method, no additional testing procedure for collecting undisturbed soil sample is required, which can reduce overall testing cost. To verify this method, for analysis, various analytical solutions were adopted and used. Measured and predicted effective stress are compared on the test results. The verification sites consist of a variety of soil condition. From comparison, it is seen that predicted value of effective stress using the propose method match well those from measured results.

• Journal of The Korean Society of Agricultural Engineers
• /
• 제47권4호
• /
• pp.43-52
• /
• 2005

It is known in some literatures that the B value is not equal to unity in saturated soil when effective stress is given, in which the B Value is the ratio of measured excess pore water pressure and isometric loading pressure. In this study the B value was measured on various effective stresses and on various incremental loading stresses in various grain size of specimens with saturated sand. The test results showed that the B value was affected largely by grain size of sand in specimen and the amount of effective stress. There was the semi-logarithmic relationship between B value and effective stress, and also there was the linear relationship between the gradient of the former semi-logarithmic relationship and grain size of specimen.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2003년도 Proceedings of the international symposium on the fusion technology
• /
• pp.703-710
• /
• 2003

In the sub-surface environments, detection of the movement of contaminant substances and recharge of groundwater by rainfall are very important factors which contain porosity and effective porosity of porous media. In this paper, the applicability of permittivity methods and proposed dielectric mixing models (DDMs) are discussed. This study showed that the ratio of effective porosity to porosity of Toyoura and River sands were 0.856 and 0.843. From the relationships between the relative porosity and effective porosity, all measured values can be confirmed to outside the range to about 0.800 for Toyoura and River sands under all experiments by FDR and FDR-V systems. In the study, this permittivity equipment can be considered to be good enough to measure determining the physical parameters of saturated soils. Consequently, this permittivity method can be contributed to estimate a porosity and effective porosity of saturated porous media because it is easy and instantaneous than previous in-situ methods.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 한국전산구조공학회 2001년도 가을 학술발표회 논문집
• /
• pp.67-74
• /
• 2001

In domestic, irregular walls such as T, L, H and Box shapes are considered as rectangular wall in the design of bearing wall apartment building. The strengths of walls, therefore, can be underestimated in case of using the current design process. Irregular walls are connected to each other as rigid joint so that part of the load can be resisted by the wall perpendicular to the load direction. This resistance can be caused by the effective width of perpendicular wall. This additional resistance by the perpendicular wall increases the strength of structural walls. The objective of this study is to evaluate the effective widths of flanged walls with different aspect ratios by using FEM analyses. the results from finite element method are compared with effective flange widths of some code provisions.

• The Journal of Asian Finance, Economics and Business
• /
• 제8권3호
• /
• pp.731-740
• /
• 2021

This research aims to investigate the determinants of real effective exchange rate in emerging ASEAN countries, including Indonesia, Malaysia, Philippines, Thailand, and Vietnam. The research was conducted by using quarterly time series data set from 1980Q1 to 2020Q3. Cointegration and the error correction model (ECM) methods were applied to test the long run and short run relationship of the real effective exchange rate and its determinants. The results indicate that the ratio of foreign direct investment to GDP and the government spending have significantly positive impact on real effective exchange rate in the Emerging ASEAN countries. The trade opening had influencing real effective exchange rate in most the Emerging ASEAN countries, except Vietnam. In addition, the international reserve (INR) had significant long-run impacts variables on real effective exchange rate in Malaysia, Thailand and Vietnam. In the short run equilibrium, the error collection term suggest that Indonesia and Malaysia are the fastest speed adjustment to equilibrium. In addition, the term of trade influence the real effective exchange rate in Indonesia, Malaysia, and the Philippines but it is not in Thailand and Vietnam. However, FDI is a major factor of the real effective exchange rate in Vietnam, but not for other countries.

• Wind and Structures
• /
• 제6권2호
• /
• pp.127-140
• /
• 2003

An investigation into the effect of corner cuts on the Strouhal number of rectangular cylinders with various dimensional ratios and various angles of attack is described. The Strouhal number given as a function of corner cut size is obtained directly from the aerodynamic behavior of the body in a uniform flow through a series of wind-induced vibration tests. For a quick verification of the validity of the Strouhal numbers obtained in this way, they are compared with the approximated the Strouhal numbers based on Shiraishi's early research. The test results show that the Strouhal number of the model with various corner cuts has a fluctuating trend as the angle of attack changes. For each cutting ratio as the angle of attack increases at each cutting ratio above $15^{\circ}$, the Strouhal number decreases gradually, and these trends are more evident for larger corner cut sizes. However, a certain corner cut size which is effective in reducing the wind-induced vibration can be identified by larger Strouhal numbers than those of other corner cut sizes. Three distinct characteristics of Strouhal number variation can be identified in three regions which are termed as Region I, II, and III based on the general trend of the test results. It is also found that the corner cut is effective in one region (Region-II) and less effective in another one (Region-III) when only the vortex-induced vibration occurs.

• Computers and Concrete
• /
• 제13권1호
• /
• pp.135-147
• /
• 2014

Strut-and-tie model (STM) has been recommended by many codes and standards as a rational model for discontinuity regions in structural members. STM has been adopted in ACI building code for analysis of reinforced concrete (RC) deep beams since 2002. However, STM recommended by ACI 318-11 is only applicable for analysis of ordinary RC deep beams. This paper aims to develop the STM for CFRP strengthened RC deep beams through the strut effectiveness factor recommended by ACI 318-11. Two sets of RC deep beams were cast and tested in this research. Each set consisted of six simply-supported specimens loaded in four-point bending. The first set had no CFRP strengthening while the second was strengthened by means of CFRP sheets using two-side wet lay-up system. Each set consisted of six RC deep beams with shear span to effective depth ratio of 0.75, 1.00, 1.25, 1.50, 1.75, and 2.00.The value of strut effectiveness factor recommended by ACI 318-11 is modified using a proposed empirical relationship in this research. The empirical relationship is established based on shear span to effective depth ratio.

• Structural Engineering and Mechanics
• /
• 제12권1호
• /
• pp.1-16
• /
• 2001

A reliable and accurate method has been developed to predict the flexural deformation response of structural concrete members subject to service load. The method that has been developed relates the extent of concrete cracking, measured as a function of the magnitude of applied moment in a member, to the reduction in the effective moment of inertia of cracked reinforced concrete members under service load conditions. The ratio of the area of the moment diagram where the moment exceeds the cracking moment, to the total area of the moment diagram for any loading, provides the basis for the calculation of the effective moment of inertia. This ratio also represents mathematically a probability of crack occurrence. Verification of this method for the determination of the effective moment of inertia has been achieved from an experimental test program, and has included beam tests with different loading configurations, and shear wall tests subjected to a range of vertical and lateral load levels. Further verification of this method has been made with reference to the experimental investigation of other recently published work.

• Structural Engineering and Mechanics
• /
• 제58권2호
• /
• pp.327-345
• /
• 2016

Many experimental and analytical studies have been conducted with beam-column subassemblages composed of a two-span beam to investigate the progressive collapse resistance of RC frames. Most study results reveal a strength-decreased transition phase in the nonlinear static load-deflection curve, which may induce dynamic snap-through response and increase the chord rotation demand for effective catenary action (ECA). In this study, the nonlinear static response is idealized as a piecewise linear curve and analytical pseudo-static response is derived for each linearized region to investigate the rotation demands for the ECA of the two-span RC beams. With analytical parameters determined from several published test results, numerical analysis results indicate that the rotation demand of 0.20 rad recommended in the design guidelines does not always guarantee the ECA. A higher rotation demand may be induced for the two-span beams designed with smaller span-to-depth ratios and it is better to use their peak arch resistance (PAR) as the collapse strength. A tensile reinforcement ratio not greater than 1.0% and a span-to-depth ratio not less than 7.0 are suggested for the two-span RC beams bridging the removed column if the ECA is expected for the collapse resistance. Also, complementary pseudo-static analysis is advised to verify the ECA under realistic dynamic column loss even though the static PAR is recovered in the nonlinear static response. A practical empirical formula is provided to estimate an approximate rotation demand for the ECA.

• Geomechanics and Engineering
• /
• 제3권3호
• /
• pp.207-218
• /
• 2011

This article describes laboratory research done on strength evaluations for stabilized samples made of tropical fibrous peat. The stabilizing agents used were ordinary Portland cement (OPC) as binding agent and blast furnace slag (BFS) as additive. Stabilized samples were tested for their strength through unconfined compressive strength (UCS) and California bearing ratio (CBR). Different dosage rates of OPC and BFS were used in trial and error experiments for the most effective combination for stabilized peat samples that were at their natural moisture content. Stabilized trial samples were air cured for 90 days. After detecting the most effective dosage rate in the trial samples, their values were used to prepare CBR samples at their optimum moisture content (OMC). CBR samples were then air cured from 1 to 90 days and tested under un-soaked and soaked conditions. The most effective dosage rate for the stabilized peat samples was found to be close to when 75% for OPC and 25% of BFS per total weight of OPC, and BFS. As an example, if 11.25% OPC, and 3.75% BFS are mixed with peat and compacted at their OMC and air cured for 90 days, stabilized peat will have an increase in CBR of 0.8% to 45 % for un-soaked and 20% for soaked conditions.