• Journal of the Korean Ceramic Society
• /
• v.24 no.4
• /
• pp.385-391
• /
• 1987

Zeta potential according to the hydration time was studied during the early hydration of C3S with and without CO2 atmosphere. Zeta potential was low as a level of 20mV at the first and second exothermic peaks of heat evolution, but it was rapidly increased up to a level of 300mV. In the CO2 atmosphere, zeta potential was level of 60mV at 10 minutes hydration and it's value became a low gradually according to the hydration time. Zeta potential was also proportioned to the Ca2+ concentration in the liquid phase, i.e., there was positive correlation between zeta potential and Ca2+ concentration. The existence of silicate layer was not found out on the hydrated C3S in the CO2 atmosphere by SEM-EDAX.

• Laser Solutions
• /
• v.4 no.1
• /
• pp.39-48
• /
• 2001

This study was performed to evaluate basic characteristics of electron beam weldability for high strength aluminum alloys. The aluminum alloys used were A5083 and A6N01, and A7N01. The principal welding process parameters, such as accelerating voltage, beam current, welding speed and chamber pressure were investigated. The dimension and microstructure of welds were evaluated with OLM, and SEM (EDAX). In addition, weldability variation(cracking) due to process parameters was also evaluated. The degree of cracking in the EB fusion zone appears to be affected mainly by aspect ratio, such that as aspect ratio increases the cracking tendency also increases. The alloying element itself may also affect the hot cracking resistance, but its role is considered to be indirect effect such that the relatively higher vaporization pressure elements of Zn and Mg give deeper weld penetration and thus results in greater cracking tendency.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.130-130
• /
• 2016

본 연구는 다양한 전산도와 유리산도 간의 산비에 따른 인산-망간 화성처리를 바탕으로 각 산비 조건에 따른 피막특성을 SEM과 EDAX로 확인 하였다. 더불어 내마모특성을 확인하고자 내마모시험을 통해 산비 조건에 따른 피막의 마찰계수를 확인하여 분석결과를 토대로 인산-망간 화성처리의 최적 산비를 도출하였다. 그 결과 산비 7.3 부근에서 최적의 표면 및 기계적 특성을 확보하였으며, 산비가 8.4로 지나치게 높거나, 산비가 6.0으로 떨어지게 되면 유리산도가 지나치게 높으면 피막 생성속도 및 결정성이 저하되어 위의 특성이 저하됨을 알 수 있었다.

• Journal of the Korean Vacuum Society
• /
• v.1 no.2
• /
• pp.291-297
• /
• 1992

알루미늄 박막 stripe에 d.c. 전류를 인가하여 electromigration에 의한 결함을 분 석하였다. 6 $\times$ 10-8Torr의 진공동에서 전자빔 증착기를 사용하여 현미경을 유리기판에 $1000AA$의 두께로 알루미늄 박막을 증착하였다. Al/glass 박막의 초기 비저항은 2.7 $\pm$ 0.15($\mu$$\Omega$cm)이였다. 알루미늄 stripe에 electromigration에 의해 양극쪽에 물질 축적영역 (hillocks)과 음극쪽에는 물질 고갈영역(voids)이 형성되었다. SEM, EDAX와 Optical microscope로 hillocks과 voids를 분석하였다. 또한 결함에 대한 SiO2 보호막효과에 대하여 도 분석하였으며, SiO2 보호막에 의하여 Al 박막의 신뢰성은 향상되었다.

• Proceedings of the KAIS Fall Conference
• /
• 2009.12a
• /
• pp.663-666
• /
• 2009

본 논문에서는 폭발법에 의해 합성된 나노다이아몬드의 열분해 및 연소특성에 대해 조사하였다. 나노 다이아몬드의 열분해 및 연소는 열중량 분석장치를 이용하여 측정하였으며, 소성된 나노다이아몬드의 표면 및 결합구조는 XRD, FT-IR, SEM-EDAX를 이용하여 측정하였다. 열분해 조건에서 나노다이아몬드는 $105{\sim}210^{\circ}C$와 $400^{\circ}C$ 부근에서 2중 피크가 나타난다. 또한 연소분위기하에서는 $420^{\circ}C$와 $490^{\circ}C$에서 2중 피크가 나타난다.

• Journal of Conservation Science
• /
• v.2 no.2 s.2
• /
• pp.25-30
• /
• 1993

Materials (refractory, stone) of iron making furnace excavated from Kalcheon were investigated by the scanning electron microscopy(SEM) with an energy dispersive X-ray analysis (EDAX), X-ray fluorescence(XRF), and X-ray diffraction(XRD). Chemical composition of the refractory materials were $SiO_2(68.74\%),\;Al_2O_3(18.40\%),\;CaO(0.42\%),\;MgO(1.04\%)\;and\;K_2O(2.26\%)$ in weight ratio, which were the typical components presented in common clay. The results of chemical analysis for the stone and the glaze coated, alkali ion(K, Na, Ca) components of the glaze contained high concentration than that the stone. It was suggested that this change had a close relationship with the kinds of fuels used.

• Tribology and Lubricants
• /
• v.12 no.3
• /
• pp.6-11
• /
• 1996

There has been a growing concern for the use of mineral oil based lubricants because of the worldwide interest in environmental issues. This has prompted the use of vegetable oils as more environmentally acceptable base fluids. In view of this, four-ball wear test was carried out to investigate the tribological behavior of selected vegetable oils blended with ZDDP, TCP and DBP under high speed and temperate conditions. Of the additive evaluated, the new additive, DBP has provided antiwear performance superior to the two other additives more commonly used. This superior performance by DBP is probably caused by different wear mechanism. This wear mechanism has been evidenced by the surface analysis of worn balls conducted using optical microscope and EDAX.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2011.06a
• /
• pp.19-19
• /
• 2011

We studied the effect of Dy content on the magnetic properties of cobalt ferrite single crystal. The $CoFe_{1.9}Dy_{0.1}O_4$ single crystals were grown by the flux method by using $Na_2B_4O_{7.}10H_2O$ (Borax) as a solvent (flux). The black and shiny single crystals were obtained as a product. The X-ray diffraction test at room temperature confirmed the spinel cubic symmetry with lattice constant a = $8.42{\AA}$ of the single crystals. The presences of constitute elements (Co, Fe and Dy) was endorsedby EDAX analysis. The saturation magnetization (Ms) of $CoFe_{1.9}Dy_{0.1}O_4$ single crystals was measured and is found to be 72emu/g or equivalently $3.2{\mu}B$/f.u. at 300 K. The observed Ms and coercivity (Hc) is found to be lower than that of pure $CoFe_2O_4$.

• Journal of the Korean Ceramic Society
• /
• v.31 no.6
• /
• pp.651-659
• /
• 1994

BaTiO3 ceramics were sintered on Al2O3, MgAl2O4, MgO and Mg-, Ca-, Y-stabilized zirconia setters. Then the influence of setters on the microstructure of BaTiO3 ceramics and the stability of setters were investigated by SEM, EDAX and XRD analyses. The microstructure of BaTiO3 ceramics sintered on Al2O3, MgAl2O4, MgO and Mg-PSZ showed large grain growth, but little grain growth on Ce-TZP(Tetragonal Zirconia Policrystal). Mg-PSZ(Partially Stabilized Zirconia), Ca-PSZ, Ce-TZP setters showed extensive phase transformation. Y-TZP and fused Y-SZ (Stabilized Zirconia) setters were stable. The liquid sintering aids of BaTiO3 ceramics accelerate mass transport. The reaction of SrTiO3 in BaTiO3 with ZrO2 resulted in the formation of SrZrO3.

• Journal of the Korean Ceramic Society
• /
• v.28 no.2
• /
• pp.160-166
• /
• 1991

Microstructure and phase changes during the sintering of ZnO varistors were studied in ZnO-Bi2O3-CoO-Sb2O3 and ZnO-Bi2O3-CoO-Sb2O3-Cr2O3 systems using acanning electron microscopy (SEM) with an energy dispersive X-ray analysis (EDAX), X-ray diffraction (XRD) and differential thermal analysis (DTA). The spinel phase and the Bi2O3 phase were formed by the decomposition of the pyrochlore phase during heating. The spinel particles (2-4$\mu\textrm{m}$), which were formed both along ther grain boundaries and within the ZnO grain, were always found near the pyrochlore phase. Intergranular phases (Bi2O3 and pyrochlore) were precipitated from the liquid phase during cooling. The Bi2O3 phases were located at the triple (or multiple) point of the ZnO grains. Cr2O3 played a role in decreasing the formation temperature of the spinel phase and Bi2O3 phase during sintering, and inhibited the grain growth.