• Journal of the Korean Society of Industry Convergence
• /
• v.17 no.4
• /
• pp.234-244
• /
• 2014

Recently it has been focused that the automobile engine has developed in a strong upward tendency for the use of the high viscosity and poorer quality fuels in achieving the high performance, fuel economy, and emission reduction. Therefore it is not easy to solve the problems between low specific fuel consumption and exhaust emission control at motor cars. In this study, it is designed and used the engine test bed which is installed with turbocharger and intercooler. In addition to equipped using CRDI by controlling injection timing with mapping modulator, it has been tested and analyzed the engine performance, combustion characteristics, and exhaust emission as operating parameters, and they were engine speeds(rpm), injection timing(bTDC), and engine load(%). From the result of an experimental analysis, peak cylinder pressure and the rate of pressure rise were increased, and the location of it was closer toward top dead center according to the increasing of engine speed and load, and with advancing injection timing. The combustion characteristics are effected by fuel injection timing due to be enhanced the mass burned fraction. Using the engine dynamometer for analyzing the engine performance, the engine torque and power have been enhanced according to advancing the fuel injection timing. In analyzing of exhaust emission, there has been a trade-off between PM and NOx with increasing of engine speed and load, and with advanced injection timing. The experimental data are shown that the formation of NOx has increased and PM, vice versa.

• Journal of Digital Convergence
• /
• v.17 no.12
• /
• pp.203-210
• /
• 2019

Most cars today use electronic control to control the state of the engine to achieve optimum performance. This study developed a device for maintaining fault diagnosis and optimal vehicle status by displaying the engine information of a car on the screen in real time using can communication. This system displays information generated from the engine to the driver in real time such as engine intake and exhaust temperature, current battery voltage, tire pressure, RPM, DPF collection amount, torque, and horsepower through the OBD2 socket. You can check immediately. It can help you to drive safely by measuring tire pressure and displaying it on the screen, and it provides a mode to set the shift timing to suit your taste. In particular, in the case of diesel engine cars, the problems caused by smoke can adversely affect the performance and environmental pollution. Therefore, the system was developed to display the DPF collection amount on the system screen to prevent environmental pollution and to manage the vehicle efficiently.

• Convergence Security Journal
• /
• v.23 no.5
• /
• pp.9-19
• /
• 2023

Smart cars, which incorporate information and communication technologies (ICT) to improve driving safety and convenience for drivers, have recently emerged. However, the increasing risk of automotive cybersecurity due to the vulnerability of electronic control units (ECUs) and automotive networks, which are essential for realizing the autonomous driving functions of smart cars, is a major obstacle to the widespread adoption of smart cars. Although there have been only a few real-world cases of smart car hacking, drivers' concerns about the security of smart cars can have a negative impact on their proliferation. Therefore, it is important to understand the risk factors perceived by drivers and the trust in smart cars formed through them in order to promote the future diffusion of smart cars. This study examines the risk factors that affect the formation of trust in smart cars, focusing on security and privacy, and analyzes how these factors affect safety perceptions and trust in smart cars.

• Journal of Drive and Control
• /
• v.12 no.4
• /
• pp.60-70
• /
• 2015

A front-end loader (FEL) mounted on an agricultural tractor is one of the most commonly used implements for farm work. However, when the tractor carries material using the bucket attached to the FEL on a sloping ground, the materials can spill or roll back over the operator due to the tilted body, thereby requiring the bucket surface to remain level at a constant value regardless of varying slopes. In this study, an active system for controlling the angle of the FEL bucket on a tractor based on the real-time measurement of ground slopes was developed to enable the bucket to constantly remain level. A FEL simulator operated based on an electro hydraulic proportional valve (EHPV) was constructed in the laboratory to develop a proportional-integral-derivative (PID) controller forming a virtual electronic control unit (ECU) on the computer, which could automatically adjust the bucket angles depending on varying input angles while sending SAE-J1939 associated messages via CAN BUS to the EHPV. The different parameter values for the PID controller due to the gravity effect of the bucket were determined using a manual PID tuning method while assuming that the tractor travels on either an ascending slope or a descending slope. The developed PID control-based self-leveling system showed a mean of steady-state errors of within $1^{\circ}$ and a mean of delayed times of ~ 0.8s when the step input of $+20^{\circ}$ was given, implying that the developed system and control algorithm would be effective in maintaining the bucket angle at a certain value. Future studies include the improvement of the control algorithm to reduce such a time delay as well as the application of the developed algorithm to the FEL mounted on a tractor tested at a testing ground.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.1
• /
• pp.82-88
• /
• 2011

Lean combustion and exhaust emission characteristics in a ethanol fueled spark-ignited engine according to ethanol-gasoline fuel blending ratio were investigated. The test engine was $1591cm^3$ and 10.5 of compression ratio SI engine with 4 cylinders. In addition, lambda sensor system was connected with universal ECU to control the lambda value which is varied from 1.0 to 1.5. The engine performance and lean combustion characteristics such as brake torque, cylinder pressure and rate of heat release were investigated according to ethanol-gasoline fuel blending ratio. Furthermore, the exhaust emissions such as carbon monoxide (CO), unburned hydrocarbon (HC), nitrogen oxides ($NO_x$) and carbon dioxide ($CO_2$) were measured by emission analyzers. The results showed that the brake torque, cylinder pressure and the stability of engine operation were increased as ethanol blending ratio is increased. Brake specific fuel consumption (BSFC) was increased in higher ethanol blending ratio while brake specific energy consumption (BSEC) was decreased in higher ethanol blending ratio. The exhaust emissions were decreased as ethanol blending ratio is increased under overall experimental conditions, however, some specific exhaust emission characteristics were mainly influenced by lambda value and ethanol-gasoline fuel blending ratio.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.6
• /
• pp.107-116
• /
• 2012

In this study, the trucks(2.9-liter) have been developed to use DME as fuel, and performance test of the vehicle's DME engine, power, emissions, fuel economy and vehicle aspects was conducted. For experiments, the fuel system(common-rail injectors and high-pressure pump included) and the engine control logic was developed, and ECU mapping was performed. As a result, the rail pressure from 40MPa to approximately 65% increase compared to the base injector has been confirmed that. Also, the pump discharge flow is 15.5 kg/h when the fuel rail pressure is 400rpm(40MPa), and the pump discharge flow is 92.1 kg/h when the fuel rail pressure is 2,000rpm(40MPa). The maximum value of full-load torque capability is 25.5 kgfm(based on 2,000 rpm), and more than 90% compared to the level of the diesel engine were obtained. The DME vehicle was developed in this study, 120 km/h can drive to the stable, and calculated in accordance with the carbon-balance method of fuel consumptions is 5.7 km/L.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.1
• /
• pp.128-136
• /
• 2003

In today's design trend of vehicle structure, crush zone is fiequently reinforced by adding a box-shaped sub-frame in order to avoid an excessive deformation against a high-speed offset barrier such as EU Directive 96/97 EC, IIHS offset test. That kind of vehicle structure design results in a relatively monotonic crash pulse for airbag ECU(Electronic Control Unit) located at non-crush zone. As for an angular crash event, the measured crash signal using a single-axis accelerometer in a longitudinal direction is usually weaker than that of frontal barrier crash. Therefore, it is not so easy task to achieve a satisfactory crash discrimination performance for offset and angular crash events. In this paper, we introduce a new crash discrimination algorithm using an electronic X-Y 2-axis accelerometer in order to improve crash discrimination performance especially for those crash events. The proposed method uses a crash signal in lateral direction(Y-axis) as well as in longitudinal direction(X-axis). A crash severity measure obtained from Y-axis acceleration is used to improve the discrimination between fire and no-fire events. The result obtained by the proposed measure is logically ORed with an existing algorithm block using X-axis crash signal. Simulation and pulse injection test have been conducted to verify the performance of proposed algorithm by using real crash data of a 2,000cc passenger vehicle.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.4
• /
• pp.17-22
• /
• 2009

FlexRay is a new standard of network communication system which provides solutions to the degradation problems generated by many ECU (Electronic Control Unit) connections in automobiles and automation systems. The upper bound of the data rate is 10Mbps and it provides two channels for redundancy In this paper, FlexRay system is first designed using SDL. For hardware implementation, FlexRay system is designed using Verilog HDL based on the SDL design result. The designed system is synthesized using Synopsys Design Compiler with the Magna/Hynix 0.18 um cell library. In this paper, to construct a FlexRay network, active star is used since active star systems can provide high speed data transmission up to 10Mbps. The performance of the star network is tested using one transmitter node and two receiver nodes.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.2
• /
• pp.166-174
• /
• 2014

Fuel injection pressure has steadily increased in diesel engines for the purpose of improving fuel efficiency and cleaning exhaust gas, but it has now reached a point, where the cost for higher pressure does not warrant additional gains. Common rail systems on modern diesel engines have fuel pumps that are mechanically driven by crankshaft. The pumps actually house two pumping module inside: a low pressure pump component and a high pressure pump component. Part of the fuel compressed by the low pressure component returns to the tank in the process of maintaining the pressure in the common rail. Since the returning fuel represents pumping loss, fuel economy improves if the returned fuel can be eliminated by using a properly controled electrical fuel pump. As the first step in developing an electrical fuel pump the fuel supply system on a 6 liter diesel engine was modeled with AMESim to analyze the workload and the fuel feed rate of the injection pump, and the results served as basis for selecting a suitable servo motor and a reducer to drive the pump. A motor controller was built using a DSP and a program which controls the common rail pressure using a proportional control method based on the target fuel pressure information from the engine ECU. A test rig to evaluate performance of the fuel pump is implemented and used to show that the newly developed electrically driven fuel pump can satisfy the fuel flow demand of the engine under various operating conditions when the rotational speed of the pump is adequately controlled.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.16 no.2
• /
• pp.81-90
• /
• 2006

The Strain Index(SI) has been commonly used to evaluate the musculoskeletal disorders(MSDs) of upper extremities. Recently, the American Conference of Governmental Industrial Hygienists(ACGIH) adopted the Threshold Limit Value for hand activity level (HAL TLV) focused on the hand, wrist, and forearm. The MSDs risks of 37 repetitive works conducted at an automobile climate control system manufacturing factory were evaluated using both the HAL TLV and the SI, and the results by two methods were compared. Also, measured repetitive frequencies of upper limbs joint were mesured using electromyogram and electrogoniometer. The evaluation results of the HAL were related with the repetitive frequency data of upper limbs joint by electrogoniometer, and the NPF was related with %MVC of ECU. The evaluation result of HAL TLV was highly related with the SI score(r=0.66, p<0.01). Of total 37 tasks, 25 tasks(67.6%) were exceeded the TLV and 34 tasks(91.9%) exceeded the SI limit. Although there was a high relationship between the HAL TLV and SI score, the HAL TLV underestimated the risk in comparison with the SI. The correlation coefficients(r) between the HAL TLV data and the repetitive frequency of upper limbs joint were 0.45~0.55(p<0.01). The MSD symptoms was significantly different between high risk groups and low risk groups evaluated by HAL TLV(p<0.01), but was not different between two groups by SI. In conclusion, the HAL TLV is a proper tool for repetitive works.