• 한국정밀공학회지
• /
• 제20권12호
• /
• pp.55-63
• /
• 2003

The traffic accident is the prerequisite of the traffic accident reconstruction. In this study, the traffic accident (forward collision) and traffic accident reconstruction (inverse collision) simulations are conducted to improve the quality and accuracy of the traffic accident reconstruction. The vehicle and tire models are used to simulate the trajectories for the post-impact motion of the vehicles after collision. The impact dynamic model applicable to the forward and inverse collision simulations is also provided. The accuracy of impact analysis for the vehicular collision depends on the accuracy of the coefficients of restitution and friction. The neural network is used to estimate these coefficients. The forward and inverse collision simulations for the multi-collisions are conducted. The new method fur the accident reconstruction is proposed to calculate the pre-impact velocities of the vehicles without using the trial and error process which requires the repeated calculations of the initial velocities until the forward collision simulation satisfies with the accident evidences. This method estimates the pre-impact velocities of the vehicles by analyzing the trajectories of the vehicles. The vehicle slides on a road surface not only under the skidding during an emergency braking but also under the steering. A vehicle over steering or cornering with excessive speed loses the traction and leaves tile yaw marks on the road surface. The new critical speed formula based on the vehicle dynamics is proposed to analyze the yaw marks and shows smaller errors than ones of the existing critical speed formula.

• 센서학회지
• /
• 제8권2호
• /
• pp.139-147
• /
• 1999

본 논문에서는 관성 항법 장치 및 동작 제어 장치 능에서 회전 각속도를 검출하기 위하여 널리 사용되는 동조 자이로스코프의 새로운 각속도 검출방법을 제시하였다. 제안된 방법은 자이로스코프의 모델을 사용하여 재평형 루프의 설계를 수행함으로써 기존의 PI제어 방법만을 사용하였을 경우보다 외부 입력에 대하여 속도 검출을 위한 픽업단의 회전각도가 과도 및 정상 상태에서 작은 검출각을 유지시킨 상태에서 입력 각속도를 검출할 수 있으며 이에 따라 자유 자이로스코프의 기계적인 변경 없이도 시스템의 동작 범위를 매우 넓히는 것이 가능함을 보였다. 제안된 방법을 사용한 동조자이로스코프 시스템의 모델 및 전달 특성을 제시하였으며 최종적으로 컴퓨터 모의실험 모델 및 그 결과를 제시하여 그 타당성을 확인하였다.

• 한국공간구조학회논문집
• /
• 제10권1호
• /
• pp.103-110
• /
• 2010

본 연구에서는 지진하중을 받는 대공간 구조물의 지진응답을 저감시키기 위하여 준능등 동조질량제어장치(STMD)를 이용한 제어기법의 가능성을 검토하여 보았다. 이를 위하여 대공간구조물의 기본적인 동적특성을 가지고 있으며 동시에 가장 간단한 구조이기도 한 아치 구조물에 일반적인 TMD 및 STMD를 설치하여 지진응답 제어성능을 평가하였다. STMD의 감쇠력을 조절하기 위해서 널리 사용되고 있는 준능동 제어알고리즘인 그라운드혹(groundhook) 제어기법을 이용하였다. STMD 및 수동 TMD의 성능검토를 위하여 조화지반가속도와 El Centro (1940) 및 Northridge (1994) 지진하중을 사용하였다. 해석결과 수동 TMD에 의해서 아치구조물의 지진응답을 효과적으로 저감시킬 수 있었으며 STMD를 사용하면 수통 TMD 보다 더욱 우수한 응답저감효과를 얻을 수 있는 것을 확인하였다.

• Structural Engineering and Mechanics
• /
• 제57권2호
• /
• pp.327-355
• /
• 2016

A new analytical derivation of the elastodynamic point load solutions for an isotropic multi-layered half-space is presented by means of the precise integration method (PIM) and the approach of dual vector. The time-harmonic external load is prescribed either on the external boundary or in the interior of the solid medium. Starting with the axisymmetric governing motion equations in a cylindrical coordinate system, a second order ordinary differential matrix equation can be gained by making use of the Hankel integral transform. Employing the technique of dual vector, the second order ordinary differential matrix equation can be simplified into a first-order one. The approach of PIM is implemented to obtain the solutions of the ordinary differential matrix equation in the Hankel integral transform domain. The PIM is a highly accurate algorithm to solve sets of first-order ordinary differential equations and any desired accuracy of the dynamic point load solutions can be achieved. The numerical simulation is based on algebraic matrix operation. As a result, the computational effort is reduced to a great extent and the computation is unconditionally stable. Selected numerical trials are given to validate the accuracy and applicability of the proposed approach. More examples are discussed to portray the dependence of the load-displacement response on the isotropic parameters of the multi-layered media, the depth of external load and the frequency of excitation.

• 대한기계학회논문집A
• /
• 제35권9호
• /
• pp.1077-1082
• /
• 2011

볼 조인트는 두 요소 사이에서 회전 및 이동이 원활하도록 돕는 역할을 하는 기계요소이다. 본 연구의 대상인 볼 조인트는 중대형 승용차량용 볼 조인트로서 너클과 컨트롤 암의 운동을 돕는다. 본 연구에서는 볼 조인트의 공정 및 시험에 관한 해석 방법을 제안하고자 한다. 볼 조인트의 제작공정은 플러깅 공정과 스피닝 공정으로 나눌 수 있다. 볼 조인트의 제작공정 및 성능시험을 암시적 수치 적분법을 적용한 상용 동역학 프로그램인 NX DAFUL 2.0 을 사용하여 해석하였다. 또한 설계요구조건을 정의하기 위하여 볼 스터드에 작용하는 응력의 평균 및 분산을 반응치로 설정하였다. 그리고 완성된 볼조인트의 유격량을 시험하는 유격시험해석을 통해 최적의 설계를 제안하였다.

• 한국해양공학회지
• /
• 제33권4호
• /
• pp.313-321
• /
• 2019

The prediction of the hydrodynamic performance of a planing hull vessel is an important and challenging topic for computational fluid dynamic (CFD) applications to naval hydrodynamics. In this paper, the resistance and planing attitude analysis for a Fridsma hull, which is a prismatic planing hull, in still water are numerically studied using OpenFOAM. OpenFOAM is an open source code package based on C++ libraries and the finite volume method (FVM) for the discretization of the RANS equation. The volume of fluid method (VOF) is used to capture the water-air interface and the SST ${\kappa}-{\omega}$ model is used for the turbulence simulation. The overset mesh method is used to capture the large motion of the hull at higher speeds. Before the extensive analysis, uncertainty analyses using various time steps and grid sizes were performed for one ship speed case of Fn = 1.19. The results of the present study are compared with those of a model test, other CFD research, and Savitsky's empirical formula. The results of the present study, following the trend of other CFD results, slightly over predict the resistance and under predict the sinkage and, more significantly, the trim.

• Current Optics and Photonics
• /
• 제6권5호
• /
• pp.445-452
• /
• 2022

We developed an adaptive optics test bench using an optical simulator and two rotating phase plates that mimicked the atmospheric turbulence at Bohyunsan Observatory. The observatory was reported to have a Fried parameter with a mean value of 85 mm and standard deviation of 13 mm, often expressed as 85 ± 13 mm. First, we fabricated several phase plates to generate realistic atmospheric-like turbulence. Then, we selected a pair from among the fabricated phase plates to emulate the atmospheric turbulence at the site. The result was 83 ± 11 mm. To address dynamic behavior, we emulated the atmospheric disturbance produced by a wind flow of 8.3 m/s by controlling the rotational speed of the phase plates. Finally, we investigated how closely the atmospheric disturbance simulation emulated reality with an investigation of the measurements on the optical table. The verification confirmed that the simulator showed a Fried parameter of 87 ± 15 mm as designed, but a little slower wind velocity (7.5 ± 2.5 m/s) than expected. This was because of the nonlinear motion of the phase plates. In conclusion, we successfully mimicked the atmospheric disturbance of Bohyunsan Observatory with an error of less than 10% in terms of Fried parameter and wind velocity.

• Geomechanics and Engineering
• /
• 제29권2호
• /
• pp.113-131
• /
• 2022

A rockburst is a common disaster in deep-tunnel excavation engineering, especially for high-geostress areas. An anomalously low friction effect is one of the most important inducements of rockbursts. To elucidate the correlation between an anomalously low friction effect and a rockburst, we establish a two-dimensional prediction model that considers the discontinuous structure of a rock mass. The degree of freedom of the rotation angle is introduced, thus the motion equations of the blocks under the influence of a transient disturbing force are acquired according to the interactions of the blocks. Based on the two-dimensional discontinuous block model of deep rock mass, a rockburst prediction model is established, and the initiation process of ultra-low friction rockburst is analyzed. In addition, the intensity of a rockburst, including the location, depth, area, and velocity of ejection fragments, can be determined quantitatively using the proposed prediction model. Then, through a specific example, the effects of geomechanical parameters such as the different principal stress ratios, the material properties, a dip of principal stress on the occurrence form and range of rockburst are analyzed. The results indicate that under dynamic disturbance, stress variation on the structural surface in a deep rock mass may directly give rise to a rockburst. The formation of rockburst is characterized by three stages: the appearance of cracks that result from the tension or compression failure of the deformation block, the transformation of strain energy of rock blocks to kinetic energy, and the ejection of some of the free blocks from the surrounding rock mass. Finally, the two-dimensional rockburst prediction model is applied to the construction drainage tunnel project of Jinping II hydropower station. Through the comparison with the field measured rockburst data and UDEC simulation results, it shows that the model in this paper is in good agreement with the actual working conditions, which verifies the accuracy of the model in this paper.

• Earthquakes and Structures
• /
• 제22권1호
• /
• pp.25-38
• /
• 2022

The RC private constructions represent a large part of the housing stock in the north part of Algeria. For various reasons, they are mostly built without any seismic considerations and their seismic vulnerability remains unknown for different levels of seismic intensity possible in the region. To support future seismic risk mitigation efforts in northern Algeria, this document assesses the seismic vulnerability of typical private RC constructions built after the Boumerdes earthquake (May 21, 2003) without considering existing seismic regulation, through the development of analytical fragility curves. The fragility curves are developed for four representative RC frames in terms of slight, moderate, extensive, and complete damage states suggested in HAZUS-MH 2.1, using nonlinear time history analyses. The numerical simulation of the nonlinear seismic response of the structures is performed using the SeismoStruct software. An original intensity measure (IM) is proposed and used in this study. It is the zone acceleration coefficient "A", through which the seismic hazard level is represented in the Algerian Seismic Regulations. The efficiency, practicality, and proficiency of the choice of IM are demonstrated. Incremental dynamic analyses are conducted under fifteen ground motion accelerograms compatible with the elastic target spectrum of the Algerian Seismic Regulations. In order to cover all the seismic zones of northern Algeria, the accelerograms are scaled from 0.1 to 2.5 in increments of 0.1. The results mainly indicate that private constructions built after the Boumerdes earthquake in the moderate and high seismic zones with four (04) or more storeys are highly vulnerable.

• Structural Engineering and Mechanics
• /
• 제86권1호
• /
• pp.1-16
• /
• 2023

The free vibration of temperature-dependent functionally graded plates (FGPs) resting on a viscoelastic foundation is investigated in this paper using a newly developed simple first-order shear deformation theory (FSDT). Unlike other first order shear deformation (FSDT) theories, the proposed model contains only four variables' unknowns in which the transverse shear stress and strain follow a parabolic distribution along the plates' thickness, and they vanish at the top and bottom surfaces of the plate by considering a new shape function. For this reason, the present theory requires no shear correction factor. Linear steady-state thermal loads and power-law material properties are supposed to be graded across the plate's thickness. Uniform, linear, non-linear, and sinusoidal thermal rises are applied at the two surfaces for simply supported FGP. Hamilton's principle and Navier's approach are utilized to develop motion equations and analytical solutions. The developed theory shows progress in predicting the frequencies of temperature-dependent FGP. Numerical research is conducted to explain the effect of the power law index, temperature fields, and damping coefficient on the dynamic behavior of temperature-dependent FGPs. It can be concluded that the equation and transformation of the proposed model are as simple as the FSDT.