• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.2
• /
• pp.392-405
• /
• 2014

SSPA experiences a growing interest in twin skeg ships as one attractive green ship solution. The twin skeg concept is well proven with obvious advantages for the design of ships with full hull forms, restricted draft or highly loaded propellers. SSPA has conducted extensive hull optimizations studies of LNG ships of different size based on an extensive hull data base with over 7,000 models tested, including over 400 twin skeg hull forms. Main hull dimensions and different hull concepts such as twin skeg and single screw were of main interest in the studies. In the present paper, one twin skeg and one single screw 170 K LNG ship were designed for optimally selected main dimension parameters. The twin skeg hull was further optimized and evaluated using SHIPFLOW FRIENDSHIP design package by performing parameter variation in order to modify the shape and positions of the skegs. The finally optimized models were then built and tested in order to confirm the lower power demand of twin skeg designed compaed with the signle screw design. This paper is a full description of one of the design developments of a LNG twin skeg hull, from early dimensional parameter study, through design optimization phase towards the confirmation by model tests.

• Journal of the Korean Society of Safety
• /
• v.32 no.3
• /
• pp.117-122
• /
• 2017

In this study, we studied the ride quality considering the deterioration effects of the three type couplers (single, double, and ring types) for EMUs. In order to know the impact occurred when an urban transit vehicle is under breaking, we tested the conditions of the service brake and the emergency brake. Normal coupler models without any slack showed similar dynamic performance results under all breaking conditions. But if the couplers become old, the initial pre-stresses are removed because of permanent compressive deformation in rubber. For three types of the old coupler models without the initial pre-stress, we evaluated dynamic performances of each type. As the results, the maximum and average acceleration levels of the double type and the ring type were similarly low in all conditions. But the accelerations of the single type coupler was high when compared to those of the double and ring types. In addition, Jerk value of the single type model associated with ride quality was high up to 15 times to the ring type in condition of the service braking in empty vehicle weight. Jerk value of the double type model was high up to 6 times to the ring type.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.7 s.178
• /
• pp.1779-1786
• /
• 2000

Most of traditional design processes of mechanical parts are regarded as sequential and discrete, since different kinds of softwas should be introduced. In this paper, we develop an integrated fram ework for virtual design and performance testing of an automobile seat. The system is composed of four modules, i.e. CAD, static analysis, dynamic analysis, and draft drawing module. In the CAD module, PRO/ENGINEER 3D seat model is created using parameters to be modified with the result of static and dynamic analysis. In the static analysis, headrest tere used in each design stage make it difficult to feedback their results to upstream process. These discrete processes may result in time loss and cost rise. In recent years, life cycle of product is reduced. To have competence with others, new concept design processt is simulated using ANSYS. In the dynamic analysis module, FMVSS201 test is simulated using DADS. Overall data flow is controlled by Motif. The advantage of the system is that even a novice can perform and review the whole design process, without a good hand at professional design/analysis S/W in each stage. The system also provides a virtual design space, where engineers in different development stage can access common data of design models. The concept could be applied to other fields and it could reduce time and money required in design process.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.24 no.1
• /
• pp.51-66
• /
• 1987

In this paper, the authors investigate theoretically the motion and longitudinal strength of ships among waves talking account of the effects of nonlinearities such as the hull shape, bottom emergence, and hydrodynamic impact. Incidentally the ship is treated as an elastic beam in heading wave condition regarding characteristics of slamming and whipping-according to the variation in the range of a quarter length of the ship forward and the increase of the elastic modes up to 4-th vibration mode were investigated by the present theory. Calculations are performed for 97m container ship and its validity is confirmed by a series of model tests. Conclusions obtained are as follows; 1) Acceleration and pressure estimated by the present theory are in good accordance with experiments. 2) The present non-linear theory may be applied for estimating longitudinal bending moment of ships in slamming and whipping conditions. 3) In investigation of the characteristic in response according to shape variation for parts under draft and vow-flare in the range of a quarter length of the ship forward, dynamic responses due to the former were much more conspicuous than those due to the later. 4) In the maximum bending moment, the considering case up to 2-the mode are larger, about $10{\sim}15%$, than that up to 4-th mode.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.7
• /
• pp.574-579
• /
• 2016

Grid systems used in previous studies were determined to be valid only if the length between the perpendiculars in a model ship was in the range of 6-8 m, and the maximum dynamic trim angle was smaller than $1^{\circ}$. The application of the grid system to a small fishing boat can create numerical instability because the dynamic trim of small boats is generally larger than $3^{\circ}$, and their Froude numbers are in the range of 0.3-0.8. In the present study, resistances of a small fishing boat were stably obtained by reducing the length between the center of buoyancy and the inlet boundary of the numerical domain, and by refining grid cells vertically in a region that would be swept by a free surface. The effective power of the small fishing boat was predicted based on the ITTC-1978 two-dimensional analysis. By using the results of previous towing tank tests, the coefficient of quasi-propulsive efficiency and the brake horsepower at a design draft were calculated.

• Ocean Systems Engineering
• /
• v.1 no.4
• /
• pp.285-296
• /
• 2011

Spar platforms have several advantages for deploying wind turbines in offshore for depth beyond 120 m. The merit of spar platform is large range of topside payloads, favourable motions compared to other floating structures and minimum hull/deck interface. The main objective of this paper is to present the response analysis of the slack moored spar platform supporting 5MW wind turbine with bottom keel plates in regular and random waves, studied experimentally and numerically. A 1:100 scale model of the spar with sparD, sparCD and sparSD configuration was studied in the wave basin ($30{\times}30{\times}3m$) in Ocean engineering department in IIT Madras. In present study the effect of wind loading, blade dynamics and control, and tower elasticity are not considered. This paper presents the details of the studies carried out on a 16 m diameter and 100 m long spar buoy supporting a 90 m tall 5 MW wind turbine with 3600 kN weight of Nacelle and Rotor and 3500 kN weight of tower. The weight of the ballast and the draft of the spar are adjusted in such a way to keep the centre of gravity below the centre of buoyancy. The mooring lines are divided into four groups, each of which has four lines. The studies were carried out in regular and random waves. The operational significant wave height of 2.5 m and 10 s wave period and survival significant wave height of 6 m and 18 s wave period in 300 m water depth are considered. The wind speed corresponding to the operational wave height is about 22 knots and this wind speed is considered to be operating wind speed for turbines. The heave and surge accelerations at the top of spar platform were measured and are used for calculating the response. The geometric modeling of spar was carried out using Multisurf and this was directly exported to WAMIT for subsequent hydrodynamic and mooring system analysis. The numerical results were compared with experimental results and the comparison was found to be good. Parametric study was carried out to find out the effect of shape, size and spacing of keel plate and from the results obtained from present work ,it is recommended to use circular keel plate instead of square plate.