• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.4
• /
• pp.839-846
• /
• 1994

This paper presents a simultaneous solution algorithm for one-dimensional unsteady flow routing through a dendritic channel system. This simulations solution algorithm is based on the double-sweep method and utilizes separate recursion equations for continuity, momentum and energy equations for each of the individual components of a dendritic channel system. Through separate recursion equations for each of the components. the new algorithm converts a dendritic channel network problem into a single-channel problem. The new algorithm is utilized in conjunction with a linearized unsteady flow model using full dynamic flow equations. The required computer storage for the coefficient matrix of the whole system is reduced significantly from the $2N{\times}2N$ matrix to a $2N{\times}4$ matrix, where N is the number of cross sections used in the computation of flow variables in a dendritic channel system. The algorithm presented in this paper provides an efficient and accurate modeling of unsteady flow events through a dendritic channel system.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.21 no.2
• /
• pp.87-93
• /
• 2017

Many studies are conducted in several fields for fragility analysis of structures or elements which is a probabilistic seismic safety analysis in consideration with uncertainty of seismic loading. It is hard to directly conduct fragility analysis for an infrastructure with social importance due to its size. Therefore, a fragility analysis for an infrastructure mainly conducted in element level or conducted with scaled model built in accordance with similarity law. In this article, fragility analysis for prototype and scaled model of reinforced concrete column was conducted with numerical models which had been updated by the results of shaking table test and pseudo dynamic test. As a result, response stress from the numerical analysis result of prototype model was higher than that from scaled model due to different stiffness ratios between steel and concrete. However, the probability of failure for scaled model was higher than that for prototype model because failure criteria for scaled model was down due to similarity law. Also it was evaluated that probability of failure by using log normal standard deviation of response stresses by spectrum matched accelerograms was more reliable than probability of failure by using existing coefficient of variation normally used.

• Wind and Structures
• /
• v.10 no.4
• /
• pp.301-314
• /
• 2007

The lever-type active multiple tuned mass dampers (LT-AMTMD), consisting of several lever-type active tuned mass dampers (LT-ATMD), is proposed in this paper to attenuate the vibrations of long-span bridges under the excitation directly acting on the structure, rather than through the base. With resorting to the derived analytical-expressions for the dynamic magnification factors of the LT-AMTMD structure system, the performance assessment then is conducted on the LT-AMTMD with the identical stiffness and damping coefficient but unequal mass. Numerical results indicate that the LT-AMTMD with the actuator set at the mass block can provide better effectiveness in reducing the vibrations of long-span bridges compared to the LT-AMTMD with the actuator set at other locations. An appealing feature of the LT-AMTMD with the actuator set at the mass block is that the static stretching of the spring may be freely adjusted in accordance with the practical requirements through changing the location of the support within the viable range while maintaining the same performance (including the same stroke displacement). Likewise, it is shown that the LT-AMTMD with the actuator set at the mass block can further ameliorate the performance of the lever-type multiple tuned mass dampers (LT-MTMD) and has higher effectiveness than a single lever-type active tuned mass damper (LT-ATMD). Therefore, the LT-AMTMD with the actuator set at the mass block may be a better means of suppressing the vibrations of long-span bridges with the consequence of not requiring the large static stretching of the spring and possessing a desirable robustness.

• Korean Journal of Agricultural Science
• /
• v.45 no.1
• /
• pp.120-127
• /
• 2018

The rural labor force has gradually been decreasing due to the decrement of the farm population and the increment of the aging population. To solve these problems, it is necessary to develop and study autonomous agricultural machinery. Therefore, analyzing the dynamic behavior of vehicles in an autonomous agricultural environment is important. Until now, most studies on agricultural machinery, especially on ground vehicle dynamics, have been done by field tests. However, these field test methods are time consuming and costly with seasonal restrictions. A research method that can replace existing field test methods by using simulations is needed. In this study, we did basic research analyzing the effect of the travelling speed of a tractor on tire slip using simulation software. A tractor simulation model was developed based on field conditions following a straight path. The simulation was done for three ranges of speed: 20 - 30 km/h (considered the normal travelling speed range), 6 - 8 km/h (considered the plow tillage speed range) and 2 - 4 km/h (considered the rotary tillage speed range). The results of the simulation show that the slip ratio and slip angle values tended to increase as the traveling speed range of the tractor decreased. From the simulation results, it can be concluded that at low tractor speeds, it becomes more difficult to control the vehicle path. In future research, simulations will be done with various work environments such as a curved path as well as with various friction coefficient conditions, and the simulation results will be experimentally verified by applying them to an agricultural tractor.

• Steel and Composite Structures
• /
• v.26 no.2
• /
• pp.125-137
• /
• 2018

In this work, the bending and free vibration analysis of multilayered plates and shells is presented by utilizing a new higher order shear deformation theory (HSDT). The proposed involves only four unknowns, which is even less than the first shear deformation theory (FSDT) and without requiring the shear correction coefficient. Unlike the conventional HSDTs, the present one presents a novel displacement field which incorporates undetermined integral variables. The equations of motion are derived by using the Hamilton's principle. These equations are then solved via Navier-type, closed form solutions. Bending and vibration results are found for cylindrical and spherical shells and plates for simply supported boundary conditions. Bending and vibration problems are treated as individual cases. Panels are subjected to sinusoidal, distributed and point loads. Results are presented for thick to thin as well as shallow and deep shells. The computed results are compared with the exact 3D elasticity theory and with several other conventional HSDTs. The proposed HSDT is found to be precise compared to other several existing ones for investigating the static and dynamic response of isotropic and multilayered composite shell and plate structures.

• International Journal of Concrete Structures and Materials
• /
• v.9 no.2
• /
• pp.159-172
• /
• 2015

Estimation of the residual strength of corroded reinforced concrete beams has been studied from experimental and theoretical perspectives. The former is arduous as it involves casting beams of various sizes, which are then subjected to various degrees of corrosion damage. The latter are static; hence cannot be generalized as new coefficients need to be re-generated for new cases. This calls for dynamic models that are adaptive to new cases and offer efficient generalization capability. Computational intelligence techniques have been applied in Construction Engineering modeling problems. However, these techniques have not been adequately applied to the problem addressed in this paper. This study extends the empirical model proposed by Azad et al. (Mag Concr Res 62(6):405-414, 2010), which considered all the adverse effects of corrosion on steel. We proposed four artificial neural networks (ANN) models to predict the residual flexural strength of corroded RC beams using the same data from Azad et al. (2010). We employed two modes of prediction: through the correction factor ($C_f$) and through the residual strength ($M_{res}$). For each mode, we studied the effect of fixed and random data stratification on the performance of the models. The results of the ANN models were found to be in good agreement with experimental values. When compared with the results of Azad et al. (2010), the ANN model with randomized data stratification gave a $C_f$-based prediction with up to 49 % improvement in correlation coefficient and 92 % error reduction. This confirms the reliability of ANN over the empirical models.

• The Korean Journal of Financial Management
• /
• v.20 no.2
• /
• pp.127-150
• /
• 2003

This study analyzes how capital market comovement can affect investors' decision making. We first analyze time-varying correlation coefficient between stock indices of U.S.A. and Korea. and then, using our empirical results, attempt to draw implications on investors' behavior. We find that the tendency of comovement between Korea and U.S.A. equity returns has considerably increased after the financial crisis of late 1997. Through the analysis of investors' behavior, we find that foreign investors, contrary to ITC's (Investment Trust Company) and individual investors, buy more shares in Korean markets as American stock prices go up. Foreign investors employ dynamic hedging strategy and give more weight on global economic factors than domestic ones. Our empirical results as a whole imply that investment behavior of foreign investors is most closely related to comovement of U.S.A. and Korea capital markets.

• Journal of Environmental Impact Assessment
• /
• v.19 no.1
• /
• pp.1-13
• /
• 2010

Ammonia ($NH_3$) is an important pollutant that plays a key role in several air pollution problems. It can create odors and have negative impacts on animal and human health. The largest source contributing to Ammonia emission is the agricultural production, in particular animal operation, in Korea. The present study evaluated flux profiles of Ammonia emitted from the cattle housing using a dynamic flux chamber. We have developed the emission factor of Ammonia from the cow housing. Analysis of Ammonia flux variation was made with respect to manure surface temperature, pH, and ammonium concentration. Ammonia has been measured from calf and cattle housing between October and December in 2007. In the fall, average Ammonia flux from calf and cattle housing was estimated 1.342(${\pm}0.728$) and 1.323(${\pm}0.655$)mg/$m^2$/min, respectively. In the winter, average Ammonia flux was estimated 0.889(${\pm}0.362$)mg/$m^2$/min from the calf housing and 0.925(${\pm}0.511$)mg/$m^2$/min from the cattle housing. The correlation coefficient between Ammonia flux and ammonium concentration showed stronger relationship than the relationship between manure pH and temperature. In the fall, Ammonia emission factor from calf and cattle housing was estimated 4.46(${\pm}2.39$) and 6.03(${\pm}3.27$)kg-$NH_3$/animal/yr, respectively. In the winter, average Ammonia flux was estimated 2.88(${\pm}1.53$) from the calf housing and 4.24({$\pm}1.63$)kg-$NH_3$/animal/yr from the cattle housing.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.3
• /
• pp.576-585
• /
• 2002

A three-dimensional Lagrangian explicit time-integration finite element code for analyzing the dynamic impact phenomena was developed. It uses four node tetrahedral elements. In order to consider the effects of strain rate hardening, strain hardening and thermal softening, which are frequently observed in high-velocity deformation phenomena, Johnson-Cook model is used as constitutive model. For more accurate and robust contact force computation, the defense node contact algorithm was adopted and implemented. In order to evaluate the performance of the newly developed three-dimensional hydrocode NET3D, numerical simulations of the oblique impact of mild steel plate by mild steel sphere were carried out. Ballistic limit about various oblique angle between 0 degree and 80 degree was estimated through a series of simulations with different initial velocities of sphere. Element eroding by equivalent plastic strain was applied to mild steel spheres and targets. Ballistic limits and fracture characteristics obtained from simulation were compared with experimental results conducted by Finnegan et al. From numerical studies, the following conclusions were reached. (1) Simulations could successfully reproduce the key features observed in experiment such as tensile failure termed "disking"at normal impacts and outwards bending of partially formed plus segments termed "hinge-mode"at oblique impacts. (2) Simulation results fur 60 degrees oblique impact at 0.70 km/s and 0.91 km/s were compared with experimental results and Eulerian hydrocode CTH simulation results. The Lagrangian code NET3D is superior to Eulerian code CTH in the computational accuracy. Agreement with the experimentally obtained final deformed cross-sections of the projectile is excellent. (3) Agreement with the experimental ballistic limit data, particularly at the high-obliquity impacts, is reasonably good. (4) The simulation result is not very sensitive to eroding condition but slightly influenced by friction coefficient.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.1236-1238
• /
• 2003

The Earth's total magnetic field was extracted from on board TAM (Three Axis Magnetometer) observations of KOMPSAT-1 satellite between June 19th and 21st, 2000. In the pre-processing, the TAM's telemetry data were transformed from ECI (Earth Centered Inertial frame) to ECEF (Earth Centered Earth Fixed frame) and then to spherical coordination, and self-induced magnetic field by satellite bus itself were removed by using an on-orbit magnetometer data correction method. The 2-D wavenumber correlation filtering and quadrant-swapping method were applied to the pre-processed data in order to eliminate dynamic components and track-line noise, respectively. Then, the spherical harmonic coefficients are calculated from KOMPSAT-1 data. To test the validity of the TAM's geomagnetic field, Danish/NASA/French ${\phi}$rsted satellite's magnetic model and IGRF2000 model were used for statistical comparison. The correlation coefficient between ${\phi}$rsted and TAM is 0.97 and IGRF and TAM is 0.96. It was found that the data from on board magnetometer observations for attitude control of Earth-observing satellites can be used to determinate the Earth's total magnetic field and that they can be efficiently used to upgrade the global geomagnetic field coefficients, such as IGRF by providing new information at various altitudes with better temporal and spatial coverage.