• 한국주조공학회지
• /
• 제30권6호
• /
• pp.210-216
• /
• 2010

The aim of this study is to characterize a thixoextruded 7075 Al wrought alloy bar in terms of its isotropic behavior through the optical microscope, mechanical test and electron back scattered diffraction. It is also discussed of the extrudability improvement for 7075 Al wrought alloy by thixoextrusion, with emphasis on controlling thixoextrusion parameters. Hot extrusion shows that the maximum extrusion pressure depends on their characteristics in terms of flow stress and hot workability. In the contrary, thixoextrusion demonstrates that the maximum extrusion pressure is almost uniform regardless of the experimental parameters, such as initial ram speed, die bearing length and thixoextrusion temperature. The hot extruded microstructures become elongated to extrusion direction, while the thixoextruded microstructures are isotropic and homogeneously distributed due to the existence of liquid phase between solid grains during the process. The grain refinement due to dynamic recrystallization during thixoextrusion has been also occurred. Subsequent recrystallization would lead to the strengthening of mechanical properties, as observed in the study. The important point is that the values of tensile, yield strength and elongation of the thixoextruded bar without plastic deformation are similar to those of the hot extruded bar with severe plastic deformation.

• Structural Engineering and Mechanics
• /
• 제51권4호
• /
• pp.663-683
• /
• 2014

In order to study the dynamic failure mechanism and aseismic measure for high concrete gravity dam under earthquake, the comparative models experiment on the shaking table was conducted to investigate the dynamic damage response of concrete gravity dam with and without the presence of reinforcement and evaluate the effectiveness of the strengthening measure. A new model concrete was proposed and applied for maintaining similitude with the prototype. A kind of extra fine wires as a substitute for rebar was embedded in four-points bending specimens of the model concrete to make of reinforced model concrete. The simulation of reinforcement concrete of the weak zones of high dam by the reinforced model concrete meets the similitude requirements. A tank filled with water is mounted at the upstream of the dam models to simulate the reservoir. The Peak Ground Acceleration (PGA) that induces the first tensile crack at the head of dam is applied as the basic index for estimating the overload capacity of high concrete dams. For the two model dams with and without strengthening tested, vulnerable parts of them are the necks near the crests. The results also indicate that the reinforcement is beneficial for improving the seismic-resistant capacity of the gravity dam.

• Structural Engineering and Mechanics
• /
• 제71권2호
• /
• pp.109-118
• /
• 2019

This paper presents the numerical simulation of membrane structure under impact load. Firstly, the numerical simulation model is validated by comparing with the test in Hao's research. Then, the effects of the shape of the projectile, the membrane prestress and the initial impact speed, are investigated for studying the dynamic response and failure mechanism, based on the membrane displacement, projectile acceleration and kinetic energy. Finally, the results show that the initial speed and the punch shape are related with the loss of kinetic energy of projectiles. Meanwhile, the membrane prestress is an important factor that affects the energy dissipation capacity and the impact resistance of membrane structures.

• 한국산업융합학회 논문집
• /
• 제27권3호
• /
• pp.519-525
• /
• 2024

In this paper, a study on the physical properties of mortar applying 3D Textile was conducted to compensate for the shortcomings of the existing concrete surface repair and reinforcement method. In the tests conducted to analyze the physical properties, compressive strength, flexural strength, and dynamic modulus measurement tests were conducted. As a result of the compressive strength test, as the number of surfaces to which the stereoscopic fiber was applied increased, the amount of displacement and strength reduction rate increased, and the flexural strength also increased as the number of surfaces to which the stereoscopic fiber was applied increased. In addition, it was confirmed that the use of stereoscopic fibers tended to decrease the dynamic modulus of elasticity. This result is a characteristic of the application of stereoscopic fibers, and it caused a decrease in compressive strength due to a decrease in the mortar content of the part to which the stereoscopic fib er was applied, and the high tensile force of the stereoscopic fiber is believed to have affected the increase in flexural strength.

• 한국건설순환자원학회논문집
• /
• 제4권3호
• /
• pp.227-234
• /
• 2016

국내 화력발전소의 추가 증설과 관련하여 발생 부산물의 신규 사용처 연구가 필요한 실정이다. 본 연구에서는 화력발전소에서 발생되는 플라이애시와 열병합발전소에서 발생되는 열병합애시, 배연탈황공정에서 발생되는 탈황석고 등 부산물로부터 아스팔트 포장용 채움재의 KS 규격을 만족하는 채움재를 제조하였다. 제조된 혼합 채움재와 기존 석회석 채움재의 특성을 비교하고, 각각의 채움재를 사용하여 아스팔트 혼합물을 제조하는 실내실험을 통해 특성을 비교하였다. 또한 혼합 채움재와 석회석 채움재를 사용하여 아스팔트 포장 현장실험을 실시하였다. 현장실험에 사용된 아스팔트 혼합물에 대해서 실내실험과 동일하게 동적안정도, 마샬안정도, 인장강도비, 포화도, 간극률, 흐름값을 평가하였다. 실내실험 및 현장시공시험 결과 기존 석회석 채움재를 사용한 경우보다 동적안정도 및 마샬안정도, 인장강도비에서 우수한 특성을 나타내었으며, 배합설계의 최적화를 통해 기존 석회석 채움재의 특성을 만족시키는 채움재 개발 가능성을 확인하였다.

• 한국산학기술학회논문지
• /
• 제18권4호
• /
• pp.391-397
• /
• 2017

최근의 DIC (Digital Image Correlation) 기술은 인장 시험 중 동적 변형을 측정하는 데 사용되고 있다. 표준 인장 시험 방법은 진응력 - 진변형 곡선을 계산하기 위해 두 표점 거리 간 측정된 평균 변위를 사용한다. 따라서, 진응력 곡선은 균일 연신 구간, 즉 네킹 변형 시작점까지만 유효하다. 반면에, DIC를 사용한다면, 전체 측정 영역에서 국부 변형을 측정할 수 있기 때문에 변형률 및 변형률 속도의 유효한 범위가 인장 시편이 파단될 때까지 확장될 수 있다. 이러한 장점 때문에 연구 및 산업 분야에서 많은 광학 3D 측정 시스템이 도입되고 사용되었지만 기존의 3D 측정 시스템은 측정하기에 너무 비싸고 시간이 많이 소요된다. 또한 장비 크기로 인해 휴대가 불편한 단점이 존재한다. 본 논문에서는 기존의 스마트 폰을 이용한 2D DIC 측정 방법과 수치 해석 기법을 사용하여 2D 측정 영상 데이터의 오차를 개선한 2D 영상 보정 방법을 수행 하였다. 2D DIC 수정 제안 된 방법의 결과는 3D 측정 장비의 정확도에 비해 더 높은 정확도를 보였다. 결론적으로, 제안 된 2D DIC 및 보정 방법이 정확하고 신속한 측정 결과를 제공한다는 것이 입증되었다.

• 소성∙가공
• /
• 제25권1호
• /
• pp.36-42
• /
• 2016

Fiber metal laminates (FMLs) are well known for improved fatigue strength, better impact resistance, superior damage tolerance and slow crack growth rate compared to traditional metallic materials. However, defects and loss of strength of a composite material can occur due to the vertical load from the punch during the joining with a dissimilar material using a conventional clinching method. In the current study, tapered-hole clinching was an alternative process used to join Al 5052 and FMLs. The tapered hole was formed in the FML before the joining. For the better understanding of static and dynamic characteristics, a clinched joining followed by a tensile-shear test was numerically simulated using the finite element analysis. The design parameters were also evaluated for the geometry of the tapered hole by the Taguchi method in order to improve and compare the lateral joining strength of the clinched joint. The influence of the neck thickness and the undercut were evaluated and the contribution of each design parameter was determined. Then, actual experiments for the joining and tensile-shear test were conducted to verify the results of the numerical simulations. In conclusion, the appropriate combination of the design parameters can improve the joining strength and the cross-sections of the tapered-hole clinched joint formed in the actual experiments were in good agreement with the results of the numerical simulations.

• 한국안전학회지
• /
• 제28권4호
• /
• pp.26-32
• /
• 2013

A digital image correlation(DIC) method is a whole-field measurement technique that acquires surface displacements and strains from images information which characterized a random speckle as intensity grey levels. Recently years, this DIC method is being developed and used increasingly in various research. In this study, we tried to apply to aluminum alloy(Al 6061-T6) using DIC method and strain gauge. DIC results demonstrated the usefulness and ability to determine a strain. The test specimen used in this study was an aluminum alloy(Al 6061-T6, thickness 1 mm). For a strain measurement, a strain gauge was attached at the center of a specimen. A specimen was lightly sprayed with a white paint and a black dot pattern was sprayed on its fully dried white surface to obtain a random speckle. The experimental apparatus used to perform the tensile test consisted of universal dynamic tester(5 kN; T.O. Co.) under displacement speed of 0.5, 1.0 and 3.0 mm/min. A Model 5100 B Scanner(V. Co.) used to obtain a strain. A CCD camera connected to a PC uses to record the images of the specimen surface. After acquisition, the images were transferred to PC where the DIC software was implemented. An acquired image was evaluated by the DIC program. DIC method for displacement and strain was suggests and it results show a good consistent remarkably. DIC results demonstrated the usefulness and ability to determine surface strain was better than by using classical measurements. The strain field measurement using a DIC is so useful that it can be applied to map strain distributions at a full area. DIC method can evaluate a strain change so it can predict a location of fracture. The findings of the investigation suggest that the DIC method is an efficient and reliable tool for full-field monitoring and detailed damage characterization of materials.

• 대한토목학회논문집
• /
• 제39권1호
• /
• pp.115-122
• /
• 2019

강섬유 습식Shotcrete는 굳지 않은 콘크리트를 노즐로부터 소정의 위치에 부착시키는 콘크리트를 시공함으로서 원지반 자체의 전단강도를 증가시켜 품질을 향상시키고 터널의 안정화를 도모한다. 강섬유 습식Shotcrete는 인장 저항능력을 증대시킴으로써 국부적인 균열의 생성 성장을 억제하는 콘크리트의 강도와 역학적 거동 특성을 개선 및 보강한다. 또한, 강섬유 습식Shotcrete는 불연속의 짧은 강섬유를 콘크리트 속에 균등하게 분산시켜 인장강도, 휨강도, 균열에 대한 저항성 등을 개선한 Shotcrete이다. 이 연구에서는 NATM 터널의 숏크리트에 대한 압축강도 시험과 휨강도 시험을 실시하고 숏크리트타설 압력을 900 RPM, 1,000 RPM, 1,100 RPM으로 변화시켜 리바운드 감소율을 측정하였다. 따라서 국내 NATM 터널공사에 적용할 수 있는 자료를 제시하였다.

• Composites Research
• /
• 제32권4호
• /
• pp.177-184
• /
• 2019

이미 제작된 복합재료 제품을 분석하여 층별로 어떤 기계적 물성을 가지는지 알아낼 수 있다면, 기존 제품에 비해 더 좋은 성능을 내는 복합재료 개발을 수행할 수 있게 된다. 본 연구에서는 프리프레그를 적층하여 제작된 복합재료 구조물에 대해 역설계 기법을 적용하여 내부 프리프레그 층의 물성을 계산하고자 하였다. 단순히 인장시험으로 얻어지는 물리량을 이용한 경우와 인장시험 및 모드 해석을 통해 얻어지는 물리량을 이용한 경우를 비교한 결과 후자의 정확도가 더 높음을 알 수 있었다. 최종적으로 예측된 $E_1$의 최대 오차는 0.09%였고 예측된 $E_2$의 최대 오차는 7%였다.