• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2009년 춘계학술대회논문집
• /
• pp.19-19
• /
• 2009

Dynamic Stall is a flow phenomenon which occurs on the retreating side of helicopter rotor blades during forward flight. It also occurs on blades of stall regulated wind turbines under yawing conditions as well as during gust loads. Time scales occurring during this process are comparable on both helicopter and wind turbine blades. Dynamic Stall limits the speed of the helicopter and its manoeuvrability and limits the amount of power production of wind turbines. Extensive numerical as well as experimental investigations have been carried out recently to get detailed insight into the very complex flow structures of the Dynamic Stall process. Numerical codes have to be based on the full equations, i.e. the Navier-Stokes equations to cover the scope of the problems involved: Time dependent flow, unsteady flow separation, vortex development and shedding, compressibility effects, turbulence, transition and 3D-effects, etc. have to be taken into account. In addition to the numerical treatment of the Dynamic Stall problem suitable wind tunnel experiments are inevitable. Comparisons of experimental data with calculated results show us the state of the art and validity of the CFD-codes and the necessity to further improve calculation procedures. In the present paper the phenomenon of Dynamic Stall will be discussed first. This discussion is followed by comparisons of some recently obtained experimental and numerical results for an oscillating helicopter airfoil under Dynamic Stall conditions. From the knowledge base of the Dynamic Stall Problems, the next step can be envisaged: to control Dynamic Stall. The present discussion will address two different Dynamic Stall control methodologies: the Nose-Droop concept and the application of Leading Edge Vortex Generators (LEVoG's) as examples of active and passive control devices. It will be shown that experimental results are available but CFD-data are only of limited comparison. A lot of future work has to be done in CFD-code development to fill this gap. Here mainly 3D-effects as well as improvements of both turbulence and transition modelling are of major concern.

• 한국항공우주학회지
• /
• 제32권5호
• /
• pp.10-17
• /
• 2004

본 연구에서는 헬리콥터의 전진비행성능 향상에 필수적인 로터블레이드의 동적실속성능을 향상시키기 위한 수동제어기법에 대한 연구를 수행하였다. 로터블레이드의 동적실속성능을 향상시키기 위해서는 블레이드 익형에 발생하는 유동박리에 대한 제어를 통해 양력 특성과 피칭모멘트 특성을 동시에 향상시켜야만 한다. 본 연구에서는 실제구현이 용이한 고정 앞전Droop과 Gurney 플랩을 심한 동적실속영역에 대해 동시에 적용하여 기존의 동적실속 제어기법에 비해서 탁월한 양력성능 향상 및 피칭 모멘트 성능 향상을 얻을 수 있음을 확인하였다.

• 한국군사과학기술학회지
• /
• 제8권3호
• /
• pp.116-123
• /
• 2005

An experimental investigation on the static and dynamic stall characteristics of elliptic airfoil was performed by PIV velocity field measurements. The flow Reynolds number was $3.13{\times}10^5$ and the reduced frequency of the pitch oscillation ranged from 0.075 to 0.125. The onset of static stall was caused by boundary layer separation which started at the trailing edge and progressed toward the leading edge. However, dynamic stall was caused by the vortex shed at the leading edge region and the flow field showed a vortex dominated flow with turbulent separation and alternate vortex shedding. The increase of reduced frequency increased the dynamic stall angle of attack and intensified the flow hysteresis in the down-stroke phase.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2004년도 추계 학술대회논문집
• /
• pp.115-119
• /
• 2004

The effect of a continuous blowing or suction on an oscillating 2-D NACA0012 airfoil was investigated numerically for the dynamic stall control. The influence of control parameter variation was also studied in the view point of aerodynamic characteristics. The result showed that the blowing control kept a higher lift drag ratio before stall angle but the dynamic stall angle was not exceed to without control result. As the slot position was closer to leading edge, the positive control effect becomes greater. The stronger jet and the smaller jet angel made more favorable roles on the control performance. In the cases of the suction, the overall control features were similar to those of the blowing, but dynamic stall angle was increased, i.e. suction was more effective to control dynamic stall. It was also founded that the suction control was showed better control effect as the slot position moves to trail edge within thirty percentage of chord length. In the simulation for the jet strength and the jet angle control, the same tendencies were observed to those of blowing cases.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2010년 춘계학술대회논문집
• /
• pp.37-39
• /
• 2010

Aerodynamic analysis was done for a fuselage and wing configuration of a mid-sized aircraft using 3-dimensional Navier-Stokes solver. Various turbulent models including a transitional SST were implemented to observe a dynamic stall as well as cruise characteristics. Also, different mesh moving methods were evaluated. Flow hysteresis which causes dynamic stall was investigated through flow field investigations.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2003년도 The Fifth Asian Computational Fluid Dynamics Conference
• /
• pp.291-293
• /
• 2003

This paper deals with a thrust generation of flapping-airfoil by dynamic stall. From many other previous research results, phase angle $ between pitching and plunging mode of flapping motion must be 90 deg. to satisfy maximum propulsive efficiency. In this case, leading edge vortex is relatively small. This phenomenon is related dynamic stall. So preventing leading edge vortex induced by dynamic stall guarantees maximum propulsive efficiency. But, in this paper we insist the leading edge vortex yields quite a positive influence on thrust generation and propulsive efficiency. In order to certify our opinion, pitching and plunging motions were calculated with the parameter of amplitude and frequency by using the unsteady, incompressible Navier-Stokes flow solver with a two-equation turbulence model. For more efficient computation, it is parallelized by MPI programming method.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.478-481
• /
• 2009

As a first step for aerodynamic analysis of vertical axis wind turbine, dynamic stall characteristics of airfoil was investigated. Dynamic stall of wind turbine airfoil is caused by severe variation of angle of attack and relative velocity of flow around airfoil. Angle of attack and relative velocity can be expressed with tip speed ratio. Variation of angle of attack is strongly dependent on the tip speed ratio. For tip speed ratio, 1.4 and free stream velocity, 15m/s, dynamic stall characteristics of wind turbine airfoil is compared with those of oscillating airfoil having same angle of attack variation.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2002년도 추계 학술대회논문집
• /
• pp.35-40
• /
• 2002

This paper deals with a thrust generation on flapping-airfoil by dynamic stall. Dynamic stall refers to a series of complicated aerodynamic phenomena accompanied by a stall delay in unsteady motion. In most cases, once it occurs, the dynamic stall may lead to an abrupt fluctuation of aerodynamic forces. An inverse $k\acute{a}rm\acute{a}n$ vortex has been considered as a main reason for a thrust generation. In this paper, however, we have found out that a thrust is closely related to reduced frequency and leading edge vortex in addition to inverse Karman vortex. In order to certify our opinion, picking and plunging motions were calculated with the parameter of amplitude and frequency by using the unsteady, incompressible Navier-Stokes flow solver with a two-equation turbulence model. For more efficient computation, it is parallelized by MPI programming method.

• 한국항공우주학회지
• /
• 제30권8호
• /
• pp.10-20
• /
• 2002

본 논문에서는 최적화 방법을 이용하여 동적 실속을 제어하는 방법을 제시하고자 한다. 비정상 공력 민감도 해석코드는 2 방정식 난류 모델을 사용한 비정상 압축성 Navier-Stokes 해석코드로부터 직접 미분법을 사용하여 개발되었다. 목적함수는 해석이 수행되는 전시간에 대한 것보다는 매 순간의 값을 사용하였다. 매 순간의 목적함수에 대한 구배값은 민감도 해석코드를 사용하여 얻었고, 최적화는 매 시간마다 간단한 건형 직선 조사방법(linear line search)을 이용하였다. 제어 변수는 익형의 노즈 반경, 최대 두께와 흡입을 사용하였다. 계산결과는 동적 실속을 제어하는데, 본 논문에서 제시한 최적화 방법이 효과적이라는 것을 보여주고 있다.

• 한국전산유체공학회지
• /
• 제16권1호
• /
• pp.48-52
• /
• 2011

Aerodynamic analysis was done for a fuselage and wing configuration of a mid-sized aircraft using unsteady 3-dimensional Navier-Stokes solver. Various turbulent models including a transitional SST were used to observe a dynamic stall as well as cruise characteristics. Also, different mesh moving methods were evaluated. Flow hysteresis which causes dynamic stall was investigated through flow field investigations.