• Journal of the Korean Institute of Intelligent Systems
• /
• 제20권5호
• /
• pp.710-715
• /
• 2010

As wind has become one of the fastest growing renewable energy sources, the key issue of wind energy conversion systems is how to efficiently operate the wind turbines in a wide range of wind speeds. The wind speed has a huge impact on the dynamic response of wind turbine. For this purpose, many control algorithms are in need for a method to measure wind speed to increase performance. Unfortunately, no accurate measurement of the effective wind speed is online available from direct measurements, which means that it must be estimated in order to make such control methods applicable in practice. In this paper, a new method based on Kalman filter and artificial neural network is presented for the estimation of the effective wind speed. To verify the performance of the proposed scheme, some simulation studies are carried out.

• Geomechanics and Engineering
• /
• 제9권5호
• /
• pp.645-667
• /
• 2015

Single treatment and staged treatments in vertical wells are widely applied in sandstone and mudstone thin interbedded (SMTI) reservoir to stimulate the reservoir. The keys and difficulties of stimulating this category of formations are to avoid hydraulic fracture propagating through the interface between shale and sand as well as control the fracture height. In this paper, the cohesive zone method was utilized to build the 3-dimensional fracture dynamic propagation model in shale and sand interbedded formation based on the cohesive damage element. Staged treatments and single treatment were simulated by single fracture propagation model and double fractures propagation model respectively. Study on the changes of fracture vicinity stress field during propagation is to compare and analyze the parameters which influence the interfacial induced stresses between two different fracturing methods. As a result, we can prejudge how difficult it is that the fracture propagates along its height direction. The induced stress increases as the pumping rate increasing and it changes as a parabolic function of the fluid viscosity. The optimized pump rate is $4.8m^3/min$ and fluid viscosity is $0.1Pa{\cdot}s$ to avoid the over extending of hydraulic fracture in height direction. The simulation outcomes were applied in the field to optimize the treatment parameters and the staged treatments was suggested to get a better production than single treatment.

• Wind and Structures
• /
• 제14권6호
• /
• pp.517-536
• /
• 2011

The assessment of wind-induced motion plays an important role in the development and design of the majority of today's structures that push the limits of engineering knowledge. A vital part of the design is the prediction of wind-induced tall building motion and the assessment of its effects on occupant comfort. Little of the research that has led to the development of the various international standards for occupant comfort criteria have considered the effects of the low-frequency motion on task performance and interference with building occupants' daily activities. It has only recently become more widely recognized that it is no longer reasonable to assume that the level of motion that a tall building undergoes in a windstorm will fall below an occupants' level of perception and little is known about how this motion perception could also impact on task performance. Experimental research was conducted to evaluate the performance of individuals engaged in a manual tracking task while subjected to low level vibration in the frequency range of 0.125 Hz-0.50 Hz. The investigations were carried out under narrow-band random vibration with accelerations ranging from 2 milli-g to 30 milli-g (where 1 milli-g = 0.0098 $m/s^2$) and included a control condition. The frequencies and accelerations simulated are representative of the level of motion expected to occur in a tall building (heights in the range of 100 m -350 m) once every few months to once every few years. Performance of the test subjects with and without vibration was determined for 15 separate test conditions and evaluated in terms of time taken to complete a task and accuracy per trial. Overall, the performance under the vibration conditions did not vary significantly from that of the control condition, nor was there a statistically significant degradation or improvement trend in performance ability as a function of increasing frequency or acceleration.

• International conference on construction engineering and project management
• /
• The 5th International Conference on Construction Engineering and Project Management
• /
• pp.539-545
• /
• 2013

Although individual-level factors (e.g., attitudes, personality) have long been associated with day-to-day attendance decisions, increasingly researchers have recognized "the social nature of attendance dynamics and their susceptibility to social control (Johns, 2008)." Implications of this social approach for research would be to focus attention on the causes and effects of absence culture (i.e., absence-related perceptions, beliefs, values), and the effects of absence culture on individual and group attendance within social units. Construction projects typically require workers to work in teams or crews on highly interdependent projects, and, thus, are particularly relevant contexts to study absence culture. In this paper we apply a system dynamics (SD) model to study absence culture by utilizing the advantages of SD in capturing a feedback process and state changes. We were particularly interested in: (a) the awareness of social norms within construction crews that pertained to attendance, (b) the interplay between formal attendance rules (policy) and these social norms, and (c) how these sources of influence affected the decision-making process of construction crew members. We expect that the results of this work will help construction organizations evaluate (or re-consider) the effects of their attendance control policies (e.g., timing, strength, and frequency) within a social context. Moreover, our findings suggest that the key to reducing excessive absences might be to invest time in influencing absence culture directly rather than imposing frequent and strict regulations - which, in turn, may inadvertently fortify a culture that works against the organization's interests.

• Journal of Distribution Research
• /
• 제14권2호
• /
• pp.1-30
• /
• 2009

The purpose of this study is to investigate the direct and indirect modes of influences environmental dynamism exerts on opportunism, one of important relationship factors. This study particularly delves into the indirect modes of influence in terms of control strategy (control mechanism) and control structure (bureaucratic structuring). To this end, a survey research has been conducted of 200 suppliers in business relationships with Korean hypermarket retailers. An analysis of the collected data indicates that while environmental dynamism has a positive influence on the control mechanisms such as monitoring and incentives, it does not have a negative influence on the control structure such as participation. And then it has a positive influence on the opportunism of suppliers. In addition, participation has a negative influence on the opportunism, but monitoring and incentives do not have a negative influence on it. This study discusses how both retailers and their suppliers should respond to the domestic retail business environment with highly dynamic characteristics, in order to achieve a long-term win-win partnership with one another. It also presents ideas to retailers with regard to what kinds of management strategies and management efforts required to effectively control the opportunism of suppliers.

• Journal of Advanced Marine Engineering and Technology
• /
• 제41권3호
• /
• pp.202-208
• /
• 2017

The recently developed marine engines for propulsion of ships have higher torsional exciting force than previous engines to improve the propulsion efficiency and to reduce specific fuel oil consumption. As a result, a viscous damper or viscous-spring damper is installed in front of marine engine to control the torsional vibration. In the case of viscous damper, it is supposed that there is no elastic connection in the silicon oil, which is filled between the damper housing and inertia ring. However, In reality, the silicon oil with high viscosity possesses torsional stiffness and has non-linear dynamic characteristics according to the operating temperature and frequency of the viscous damper. In this study, the damping characteristics of a viscous damper used to control the torsional vibration of the shafting system have been reviewed and the characteristics of torsional vibration of the shafting system equipped with a corresponding viscous damper have been examined. In addition, it is examined how to interpret the theoretically optimal dynamic characteristics of a viscous damper for this purpose, and the optimum design for the propulsion shafting system has been suggested considering the operating temperature and aging. when the torsional vibration of the shafting system is controlled by a viscous damper filled with highly viscous silicon oil.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• 제7권3호
• /
• pp.82-94
• /
• 2008

Airport GIS is a comprehensive information system to improve security and efficiency of airport. At the initial stage to make it real, the current status of domestic and international regulations along with relevant standardization bas been reviewed. Gimpo Airport becomes a test-bed to get some ideas about how to bring the airport GIS into workflow by building service model and basic design based on current status and demand analysis of the airport. The 6 service models primarily brought into the project are as follows: (1) Local vehicles safety management in airside, (2) Intelligent traffic control between flights and vehicles at main cross points, (3) Dynamic safety management against FOD in airside and breakage on pavement, (4) Special support vehicle management such as deicing remotely controlled, (5) Response and support for fire vehicles and ambulances of signatory institutions in emergency. The upcoming research topic aims at drawing a specific design and building integrated system in the future.

• Journal of the Korea Computer Graphics Society
• /
• 제1권2호
• /
• pp.201-212
• /
• 1995

This paper presents a new method of dynamics-based synthesis of bipedal, especially human, walking. The motion of the body at a time point is determined by ground reaction force and torque under the support foot and joint torques of the body at that time point. Motion synthesis involves specifying conditions that constrain ground reaction force and torque, and joint torques so that a given desired motion may be achieved. There are conditions on a desired motion which end-users can think of easily, e.g. the goal position and orientation of the swing foot for a single step and the time period of a single step. In this paper, we specify constraints on the motion of the support foot, which end-users would find difficult to specify. They are constraints which enforce non-sliding, non-falling, and non-spinning the support foot. They are specified in terms of joint torques and ground reaction force and torque. To satisfy them, both joint torques and ground reaction force and torque should be determined appropriately. The constraints on the support foot themselves do not give any good clues as to how to determine ground reaction force and torque. For that purpose, we specify desired trajectories of the application point of vertical ground reaction force (ground pressure) and the application point of horizontal ground reaction (friction) force. The application points of vertical pressure and friction force are good control variables, because they are indicators to kinds of walking motions to synthesize. The synthesis of a bipedal walking motion, then, consists of finding a trajectory of joint torques to achieve a given desired motion, so that the constraints are satisfied under the condition of the prescribed center of pressure and center of friction. Our approach is distinguished from many other approaches, e.g. the inverted-pendulum approach, in that it captures and formulates dynamics of the support foot and reasonable constraints on it.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• 제12권1호
• /
• pp.151-158
• /
• 1992

Topographic mapping from economic SPOT stereo imagery than aerial photographs has become possible. Many of authors have studied the possibility of base map revisions and the accuracy of results. They have concluded that the SPOT image is suitable for 1/50,000 to 1/100,000 topographic map. For topographic map, orthophoto and DTM generation from SPOT imagery, accurate exterior orientation parameters are needed. But since the geometric characteristic of SPOT image is dynamic linear array imagery, the conventional bundle adjustment for photogrammetry can not be directly applied. Reliability is the ability to detect gross error, which is called the internal reliability, and the effect of non-detectable gross error on the results of exterior orientation, which is called the external reliability. This paper shows how the reliability of SPOT imagery depends on the different coordinate systems, presentations of coordinate for flight direction, orders of exterior orientation parameters and distribution of control points, and thus analyses the theoretical reliability of the exterior orientation, which can provide a basis for the planning of SPOT projects.

• KIEAE Journal
• /
• 제15권5호
• /
• pp.13-20
• /
• 2015

Purpose: In order to upgrade the energy performance of existing building, energy audit stage should be implemented first because it is useful method to find where the problems occur and know how much time and cost consumption for retrofit. In overseas researches, three levels of audit is proposed whereas there are no standards for audit in Korea. Besides, most studies use dynamic simulation in detail like audit level 3 even though the level 2 can save time and cost than level 3. Thus, this paper focused on audit level 2 and proposed the audit method with the simple linear regression analysis model. Method: Two parameters were considered for the simple regression analysis, which were the monthly electric use and the mean outdoor temperature data. The former is a dependent variable and the latter is a independent variable, and the building's energy performance profile was estimated from the regression analysis method. In this analysis, we found the abnormal point in cooling season and the more detailed analysis were conducted about the three heat source equipments. Result: Comparing with real and predicted models, the total consumption of predicted model was higher than real value as 23,608 kWh but it was the results that was reflected the compulsory control in 2013. Consequently, it was analyzed that the revised model could save the cooling energy as well as reduce peak electric use than before.