• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1309-1313
• /
• 2008

This paper suggests an example of modification of the durability test specifications of electronic control unit for an automotive system in phase of design validation. The basic concept to redefine the specifications of durability test is based on the Arrhenius relationship for accelerated temperature test and the modified Coffin-Manson model for temperature cycle test. The ambient temperature of the powered-event durability test is increased to reduce the required test time of the current specification. Furthermore, the holding time between the events to cool down the temperature of the components is shortened and the resultant temperature rise affects the durability of the components. Thus, the acceleration factor due to the increased temperature range of temperature cycle is also estimated by the modified Coffin-Manson model.

• 한국안전학회지
• /
• 제10권2호
• /
• pp.24-31
• /
• 1995

This paper shows the fatigue durability test method for vehicle suspension systems. Durability should be assured for the safe driving during vehicle life cycle. A computer simulation for the vehicle dynamics was used to obtain dynamic loads that were required for the fatigue durability test. Durability tests were done for an Important load-carrying component of the suspension system. Stress analyses using stresscoat and strain gages were also done for the component. This study demonstrated an effective method for the fatigue durability test.

• 한국음향학회지
• /
• 제37권4호
• /
• pp.233-241
• /
• 2018

본 논문에서는 기존에 없었던 도어트림 그립핸들에서 반복된 하중으로 인해 발생하는 소음을 사전에 검증할 수 있는 내구 시험법을 개발하고자 하였다. 시험 방법은 그립 핸들이 받는 하중 모드, 내구 횟수를 고려하여 개발하였으며, 시험 방법의 유효성을 확인하기 위해, 양산 초기 제품에 시험 법을 적용하여 필드클레임에서 발생한 도어트림 그립 핸들 소음을 재현하였다. 최종적으로, 현재 개발된 시험법을 통해서 후속 개발 제품의 소음 검출 및 개선하는 데 활용하고 있다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.83-83
• /
• 2009

The automotive chassis components are structural assemblies that support the engine, suspension, and steering components of the vehicle. For the development of AHSS components, the durability analysis is important. In this paper, the low cycle fatigue property of AHSS was evaluated for the geometry complex and local plasticity in the base material. The GMAW optimization was implemented for the weld soundness using the moving least square method. And the weld S-N curves of AHSS were evaluated to access durability analysis for the weld region. For the verification, the durability analysis of the couple torsion beam axle (CTBA) was performed and compared to the rig test result. The durability analysis using the low cycle fatigue property and the evaluated weld S-N curve of AHSS met the good agreement with the test result.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 추계 학술논문 발표대회
• /
• pp.65-67
• /
• 2014

There are many elastomeric joint sealant applications in construction such as structural glazing, weatherproofing and insulating glass fabrication etc. Each sealant joints require unique durability functions to perform well through building life cycle. Elastomeric joints in bathroom and kitchen is one of areas which require durable sealing. In this application, anti fungal durability is proprietary function of sealant during building life cycle. Premature failure of anti fungus resistance of sealant is putting big stresses to general contractor as well as the inhabitants due to costly rework and poor sanitation. Accordingly, when chemists design a product, they must take into account various parameters not only formulation components also test conditions in order to have long term fungal durability. This paper reviews several biocide options with various industry standards for fungus resistance performance to suggest making new test method for construction sealant industry.

• 한국콘텐츠학회논문지
• /
• 제18권11호
• /
• pp.455-461
• /
• 2018

본 논문에서는 DFRCC 보수모르타르와 탄소섬유시트를 사용하여 보수보강을 실시한 철근콘크리트보를 대상으로 동결융해시험을 실시하여 휨강도 및 동탄성계수를 측정하고 비교 평가한 실험적 연구결과를 제시하였다. 이를 위해 $100{\times}100{\times}400mm$ 크기의 각주형 보를 총 14개 제작하여 KS F 2456에 따른 동결융해시험과 휨강도 시험을 실시하였다. 인장 및 압축측에서 각각 3-D10의 철근을 배치하였으며, 보수보강은 보의 3면에 각각 실시하였다. 동결융해시험에서는 각각 100 Cycle 및 200 Cycle에서 상대동탄성계수를 산정하였다. 실험결과, 휨강도에서는 탄소섬유시트를 사용한 경우가 DFRCC 보수모르타르의 경우보다 약 15% 정도 크게 나타났으며, 동탄성계수 측면에서는 큰 차이를 보이지 않았다. 이는 공시체 크기에 비해 비교적 많은 철근량이 배근되어 간섭효과가 나타난 것으로 추정되어 추가적인 실험과 연구가 필요한 것으로 판단된다.

• 한국농공학회지
• /
• 제22권3호
• /
• pp.60-74
• /
• 1980

Soil-cement mixtures involve problems in it's durability in grain size distribution and mineral composition of the used soils as well as in cement content, compaction energy, molding water content, and curing. As an attempt to solve the problems associated with durability of weathered granite soil with cement treated was investigated by conducting tests such as unconfined compression test, it's moisture, immers, wet-dry and freeze-thaw curing, mesurement of loss of weight with wet-dry and freeze-thaw by KS F criteria and CBR test with moisture curing on the five soil samples different in weathering and mineral composition. The experimental results are summarized as follows; The unconfined compressive strength was higher in moisture curing rather than in the immers and wet-dry, while it was lowest in freeze-thaw. Decreasing ratio of unconfined compressive strength in soil-cement mixtures were lowest in optimum moisture content or in the dry side rather than optimum moisture content with freeze-thaw. The highly significant ceofficient was obtained between the cement content and loss of weight with freeze-thaw and wet-dry. It was possible to obtain the durability of soil-cement mixtures, as the materials of base for roads, containing above 4 % of cement content, above 3Okg/cm$_2$ of unconfined compressive trength with seven days moisture curing or 12 cycle of freeze-thaw after it, above 100% of relative unconfined compressive strength, 80% of index of resistance, below 14% of loss of weight with 12 cycle of wet-dry and above 1. 80g/cm$_2$ of dry density.

• Geomechanics and Engineering
• /
• 제34권1호
• /
• pp.51-67
• /
• 2023

In this research, the degradation rate of physical properties of the Angouran pit bedrock (calc-schist) is first investigated under the specific numbers of freeze-thaw (F-T) cycles. Then, the durability of calc-schist specimens against the F-T cycle number (N) is examined considering the mechanical parameters, and using the decay function and half-time techniques. For this purpose, point load strength (I_S(50)), second durability index (I_d2), Brazilian tensile strength (BTS), and compressive (V_P) and shear (V_S) wave velocities of calc-schist specimens are measured after 0, 7, 15, 40, and 75 N. For comparing the degradation rate of mechanical properties of available rock types on the Angouran mine walls, these tests are also carried out on the limestone and amphibolite schist specimens beside the calc-schist. According to test results, the exponential regression models are developed between the mechanical parameters of rock specimen's and N variable. Also, the long-term durability of each rock type versus N is studied using the decay function and half-time techniques. Results indicated that the degradation rate differs for the above rock types in which amphibolite schist and calc-schist specimens have the highest and least resistance against the N, respectively. The obtained results from this study can play a key role in the optimal design of the mine's final walls.

• 한국자동차공학회논문집
• /
• 제23권6호
• /
• pp.575-582
• /
• 2015

The Durability cycle is very important for the success of vehicle testing to evaluate Retarder. The purpose of this study is to develop the durability mode on performance evaluation of retarder. Commercial vehicles are equipped with an auxiliary braking device in order to increase safety. A typical device for retarder depends heavily on imports. Domestic development has now become an urgent task. But, No state has an evaluation method for performance evaluation of the auxiliary braking device. We presented the durability test mode for the performance evaluation of the retarder was verified experimentally.

• Tribology and Lubricants
• /
• 제22권3호
• /
• pp.131-136
• /
• 2006

Cylinder bore wear may not be a problem in most current automotive engines. However, a small change in cylinder bore diameter can significantly affect the lubrication characteristics and ring axial motion. This in turn can cause to change inter-ring pressure, blow-by and oil consumption in an engine. Therefore, by predicting the wear of piston ring face, ring groove and cylinder bore altogether, the changed ring end gap and the changed volume of gas reservoir can be calculated. Then the excessive oil consumption can be predicted. Being based on the calculation of gas flow amount by the theory of piston ring dynamics and gas flow, and the calculation of oil film thickness and friction force by the analysis of piston ring lubrication, the calculation theory of oil amount through top ring gap into combustion chamber will be set. This is estimated as engine oil consumption. Furthermore, the wear theories of ring, groove and cylinder bore are included. Then the each amount of wear is to be obtained. The changed oil consumption caused by the new end gap and the new volume of oil reservoir around second land, can be calculated at some engine running interval. Meanwhile, the wear amount and oil consumption occurred during engine durability cycle are compared with the calculated values. Next, the calculated amount of oil consumption and wear are compared with the guideline of each pare0s wear and oil consumption. So, the timing of part repair and engine life cycle can be predicted in advance without performing engine durability test. The wear data of cylinder bore diameter are obtained from three engines before and after engine durability test. The calculated wear data of cylinder bore diameter are turn out to be twice of the lower bound of averaged test values at TDC and the lower bound at BDC.