• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.628-631
• /
• 2010

환경문제에 대한 관심으로 자동차에 대한 경량화가 요구되는 동시에 안전규제가 강화 되고 있어, 높은 인장강도를 가지는 고강도 강의 차체 적용 비율이 점차 증가하고 있다. 또한, 자동차 1대를 조립하기 위한 저항 점용접 횟수를 줄이고, 용접부에 충격안정성을 확보하기 위한 관심이 고조되고 있다. 따라서, 국내 자동차 산업에서 용접부의 신뢰성을 보장하기 다양한 비파괴 검사를 적용하고 있으며, 생산 공정에 적용하고 있다. 그중에서 용접 전극 사이에서 동저항(Dynamic resistance, 용접 공정중모재의 저항값의 변화)을 계측하여 용접성을 평가하는 방법이 제시되고, 차체 조립공정 중에 적용하려는 시도가 이루어지고 있다. 본 연구에서는 자동차 차체용 냉간 압연강판(590MPa dual-phase steel)을 인버터 DC 저항 점 용접하여, 용접전극 사이에서 동저항을 측정 하였다. 용접성은 인장전단 강도로 평가하였고, 용접 공정 변수는 용접 전류, 용접 시간, 가압력을 선정하였다. 동저항 그래프의 ${\alpha}$-peak와 ${\beta}$-peak값을 인장전단 강도에 따라 회귀 분석하여, 동저항에 따른 인장전단 강도를 예측하였다. 추가적으로, 용접부의 외관 형상 중에 압흔 깊이와 압흔자국 지름에 대한 회귀분석을 실시하였으며, 용접부 형상에 대한 신뢰성을 부여하였다.

• Journal of Surface Science and Engineering
• /
• v.46 no.5
• /
• pp.229-233
• /
• 2013

The small punch(SP) tests that can be applied to high strength sheet steel in automobile were carried out to evaluate the behavior of hydrogen embrittlement of DP sheet steels. In order to charge hydrogen at DP sheet steels, DP sheet steels were treated by the electrochemical hydrogen charging method under the charging conditions of current densities of 100, 150 and 200 $mA/cm^2$ for charging times of 5, 10, 25 and 50 hrs. Respectively, After hydrogen charging with experimental conditions, SP tests were performed. From the SP results, the correlations between the variation of bulb diameters and bulb heights with the hydrogen charging conditions were analysed. It was shown that the variation of bulb diameters were not significant with the hydrogen embrittlement due to the amounts of hydrogen charging. On the other hand, the bulb heights were observed to decrease with increasing hydrogen contents. It was thought that these results of the variation of bulb shapes after SP tests would be estimated as the index of evaluation of hydrogen embrittlement.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.68-68
• /
• 2009

Recently, resistance spot welding using Inverter DC is applied to improve the weldability of high strength steel for the auto-body fabrication. In this study, inverter DC spot welding machine, which is developed in the domestic, was evaluated weldability of the galvanized and cold rolled dual-phase steel(tensile strength : 590MPa). The welding conditions (welding time, current and force) were decided by tensile-shear test, and welding strength and nugget size were analyzed by statistical analysis methods which involved dynamic resistance and indentation. The results of the statistical analysis was utilized for real-time estimation of the invisible nugget size and tensile strength. Moreover, it can be achieved without the conventional destructive testing of welds.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.4
• /
• pp.214-226
• /
• 1992

In this paper, the characteristics of fatigue crack growth in the spot welded joint of the same kinds of specimens($HS{\times}HS,\;GA{\times}GAB$) and different kinds of specimens($HS{\times}GA,\;HS{\times}GAB$) which consist of dual phase high strength steel(HS) and monogalvanized steel(GA) were examined with static tension tests and axial tension fatigue tests. Some of the important results are as follows : 1. The divergence of tensile strengths among the same and different kinds of spot welds under the same conditions is comparatively low regardless of the difference of stiffness. 2. At the low load bevel and long life legion, the fatigue crack is initiated near the nugget. However, in the high load level and short life region, it occurs a tittle far from the nugget. 3. It has shown a linear relation between maximum stress Intensity factor, Kmax and fatigue life, $N_f$ among each of the spot welds and has gathered in a narrow band on the log-log graph paper. $Kmax=H{\cdot}{N_f}^{P}$ where H and P are a material constant.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.1
• /
• pp.127-130
• /
• 2010

This paper deals with the formability of DP590 steel considering the strain rate. The strain hardening coefficient, elongation and r-value were obtained from the static and dynamic tensile test. As strain rate increases from static to 100/s, the strain hardening coefficient and the uniform elongation decrease and the elongation at fracture and r-value decrease to 0.1/s and increase again to 100/s. The high speed forming limit tests with hemi-spherical punch were carried out using the high speed crash testing machine and high speed forming jig. The high speed forming limit of DP590(order of $10^2$/s) decreases compared to the static forming limit(order of $10^{-3}$/s) and the forming limit band in high speed forming test is narrower than that in the static forming test. This tendency may be due to the development of brittleness with increase of stain rate.

• Journal of the Korean Institute of Gas
• /
• v.18 no.5
• /
• pp.40-46
• /
• 2014

The hydrogen embrittlement degree of 5 type high strength DP steel charged with hydrogen by electrochemical method was evaluated by small punch test(SP test). After SP test, SP absorbed energy was remarkably decreased from 363 kgf-mm to 209 kgf-mm with increasing hydrogen charging time from 5hr to 50hr at DP5 specimen under the $200mA/cm^2$ current density condition. It was investigated that the decrease of hydrogen charging amount and SP absorbed energy according to the increase of current density and hydrogen charging time had a linear relationship. And it also investigated that the change of bulb height appeared by the SP test was decreased from 1.79mm to 1.59mm with the hydrogen charging conditions. It was supposed that it could be used as indicator of the evaluation of hydrogen embrittlement because of the similar trend of the formal results of SP absorbed energy. From the SEM observation of fracture area by crack in bulb, the morphology of fracture surface according to increasement of the hydrogen charging amount was varied with the cleavage mode.