• Tribology and Lubricants
• /
• v.40 no.1
• /
• pp.24-27
• /
• 2024

A monotype valve body for a dual clutch transmission has the potential to reduce costs, weight, and manufacturing time by modularizing various parts, including those of existing solenoid packs and valve bodies, into one through the application of super-precision die casting technology. However, this approach may lead to challenges such as reduced rigidity and increased interference due to modularization and compactness, impacting both product performance due to the reduced weight as well as durability and reliability. Unlike existing products, this approach requires a high-precision thin-wall block to avoid more complicated flow line formation, interference between flow lines, and leaks, as well as a strict quality requirement standard and precise inspections including detection of internal defects. To conduct precise inspections, we built an equivalent model corresponding to a driving distance of 300,000 km. Testing involved simulating actual road loads using a real vehicle and a chassis dynamometer in the FTP-75 mode (EPA Federal Test Procedure). The aim of the study was to establish a vehicle load-based part durability model for manufacturing a mono-type valve body and to develop fundamental technology for part weight reduction through preliminary design by introducing analytical weight reduction technology based on the derived results.

• Membrane Journal
• /
• v.9 no.1
• /
• pp.25-35
• /
• 1999

The sorption and permeation experiments with $O_2$ and $N_2$ were performed with poly sulfone hollow-fiber membrane to obtain oxygen-enriched air. Sorption of $O_2$ on poly sulfone membrane was 1.5'||'&'||'not;2.0 times higher than that of N2. Sorption of oxygen and nitrogen in poly sulfone membrane was described satisfactorily with "dual-mode sorption model". In the low pressure range below 3kgr!cm', about 85% of total sorption was Langmuir-type sorption and only 15% was Henry-type sorption. In the higher pressure above 3kgf/${cm}^2$, Langmuir sorption sites became almost saturated and reached asymptote, and the increase in total sorption with pressurizing might be due to the Henry~type sorption. The ideal separation factor ( P $O_2$/ P $N_2$) was in the range of 2~4, while the actual separation factor for the mixture was reduced to the value of 1.7~2.2.2.2.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.30 no.3
• /
• pp.65-72
• /
• 2016

This paper discussed the LCL-type & Isolated bidirectional dc-dc converter(BDC) with dual full bridge inverter. In order to verify the analysis of the BDC, Experimental prototype has been designed and implemented to supply constant voltage regardless of loads and proposed a method to select switching frequency that depended on two inductors' inductance ratio and transformer parameters. The proposed converter has been composed of LCL resonant network with unit inductance ratio ($L_r/L_f$=1) and then operated with fixed duty, 50% duty ratio and fixed frequency. There are some characteristics that input voltage and output voltage of the BDC is nearly identical and zero voltage turn-on switching is possible in forward and reverse mode. Finally, it has been showed that BDC is possible to commutate operating mode normally and provide constant output voltage in selected switching frequency.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.311-311
• /
• 2016

최근 고성능 디스플레이 개발이 요구되면서 기존 비정질 실리콘(a-Si)을 대체할 산화물 반도체에 대한 연구 관심이 급증하고 있다. 여러 종류의 산화물 반도체 중 a-IGZO (amorphous indium-gallium-zinc oxide)가 높은 전계효과 이동도, 저온 공정, 넓은 밴드갭으로 인한 투명성 등의 장점을 가지며 가장 연구가 활발하게 보고되고 있다. 기존에는 SG(단일 게이트) TFT가 주로 제작 되었지만 본 연구에서는 DG(이중 게이트) 구조를 적용하여 고성능의 a-IGZO 기반 박막 트랜지스터(TFT)를 구현하였다. SG mode에서는 하나의 게이트가 채널 전체 영역을 제어하지만, double gate mode에서는 상, 하부 두 개의 게이트가 동시에 채널 영역을 제어하기 때문에 채널층의 형성이 빠르게 이루어지고, 이는 TFT 스위칭 속도를 향상시킨다. 또한, 상호 모듈레이션 효과로 인해 S.S(subthreshold swing)값이 낮아질 뿐만 아니라, 상(TG), 하부 게이트(BG) 절연막의 계면 산란 현상이 줄어들기 때문에 이동도가 향상되고 누설전류 감소 및 안정성이 향상되는 효과를 얻을 수 있다. Dual gate mode로 동작을 시키면, TG(BG)에는 일정한 positive(or negative)전압을 인가하면서 BG(TG)에 전압을 가해주게 된다. 이 때, 소자의 채널층은 depletion(or enhancement) mode로 동작하여 다른 전기적인 특성에는 영향을 미치지 않으면서 문턱 전압을 쉽게 조절 할 수 있는 장점도 있다. 제작된 소자는 p-type bulk silicon 위에 thermal SiO2 산화막이 100 nm 형성된 기판을 사용하였다. 표준 RCA 클리닝을 진행한 후 BG 형성을 위해 150 nm 두께의 ITO를 증착하고, BG 절연막으로 두께의 SiO2를 300 nm 증착하였다. 이 후, 채널층 형성을 위하여 50 nm 두께의 a-IGZO를 증착하였고, 소스/드레인(S/D) 전극은 BG와 동일한 조건으로 ITO 100 nm를 증착하였다. TG 절연막은 BG 절연막과 동일한 조건에서 SiO2를 50 nm 증착하였다. TG는 S/D 증착 조건과 동일한 조건에서, 150 nm 두께로 증착 하였다. 전극 물질과, 절연막 물질은 모두 RF magnetron sputter를 이용하여 증착되었고, 또한 모든 patterning 과정은 표준 photolithography, wet etching, lift-off 공정을 통하여 이루어졌다. 후속 열처리 공정으로 퍼니스에서 질소 가스 분위기, $300^{\circ}C$ 온도에서 30 분 동안 진행하였다. 결과적으로 $9.06cm2/V{\cdot}s$, 255.7 mV/dec, $1.8{\times}106$의 전계효과 이동도, S.S, on-off ratio값을 갖는 SG와 비교하여 double gate mode에서는 $51.3cm2/V{\cdot}s$, 110.7 mV/dec, $3.2{\times}108$의 값을 나타내며 훌륭한 전기적 특성을 보였고, dual gate mode에서는 약 5.22의 coupling ratio를 나타내었다. 따라서 산화물 반도체 a-IGZO TFT의 이중게이트 구조는 우수한 전기적 특성을 나타내며 차세대 디스플레이 시장에서 훌륭한 역할을 할 것으로 기대된다.

• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.1
• /
• pp.44-50
• /
• 2015

This paper presents a high speed synchronous single inductor dual output boost converter using Type-III compensation for power management in smart devices. Maintaining multiple outputs from a single inductor is becoming very important because of inductor the sizes. The uses of high switching frequency, inductor and capacitor sizes are reduced. Owing to synchronous rectification this kind of converter is suitable for SoC. The phase is controlled in time sharing manner for each output. The controller used here is Type-III, which ensures quick settling time and high stability. The outputs are stable within $58{\mu}s$. The simulation results show that the proposed scheme achieves a better overall performance. The input voltage is 1.8V, switching frequency is 5MHz, and the inductor used is 600nH. The output voltages and powers are 2.6V& 3.3V and 147mW &, 230mW respectively.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.4 s.181
• /
• pp.183-190
• /
• 2006

Digital 3D Real Object Duplication System (RODS) consists of 3D Scanner and Solid Freeform Fabrication System (SFFS). It is a device to make three-dimensional objects directly from the drawing or the scanning data. In this research, we developed an office type SFFS based on Three Dimensional Printing Process and an industrial SFFS using Dual Laser. An office type SFFS applied sliding mode control with sliding perturbation observer (SMCSPO) algorithm for control of this system. And we measured process variables about droplet diameter measurement and powder bed formation etc. through experiments. In case of industrial type SFFS, in order to develop more elaborate and speedy system for large objects than existing SLS process, this study applies a new Selective Dual-Laser Sintering (SDLS) process and 3-axis Dynamic Focusing Scanner for scanning large area instead of the existing f lens. In this process, the temperature has a great influence on sintering of the polymer. Also the laser parameters are considered like that laser beam power, scan speed, and scan spacing. Now, this study is in progress to evaluate the effect of experimental parameters on the sintering process.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.399-400
• /
• 2012

The proposed battery charger presented in this paper is suitable for Lead-Acid Battery and the dc/dc buck converter topology is applied as a charger circuit. The technique adopted in this charger is constant current & constant voltage dual mode, which is decided by the value of voltage of proposed battery. Automatic mode change function is detected by the percentage value of level of battery charging. CC Mode (Constant Current Mode) is operated when charging level is below 80% of the total charging of Battery voltage and above 80% of battery voltage charging, CV Mode (Constant Voltage Mode) is automatically operated. As the charging level exceeds 120%, it automatically terminates charging. The feedback signal to the PWM generator for charging the battery is controlled by using the current and voltage measurement circuits simultaneously. This technique will degrade the damage of proposed type of battery and improve the power efficiency of charger. Finally, a prototype charger circuit designed for a 12-V 7-Ah lead acid battery is constructed and tested to confirm the theoretical predictions. Satisfactory performance is obtained from simulation and the experimental results.

• Journal of the Ergonomics Society of Korea
• /
• v.33 no.3
• /
• pp.241-253
• /
• 2014

Objective: The objective of this study was to examine multi-modal interaction effects of input-mode switching on the use of smart phones. Background: Multi-modal is considered as an efficient alternative for input and output of information in mobile environments. However, there are various limitations in current mobile UI (User Interface) system that overlooks the transition between different modes or the usability of a combination of multi modal uses. Method: A pre-survey determined five representative tasks from smart phone tasks by their functions. The first experiment involved the use of a uni-mode for five single tasks; the second experiment involved the use of a multi-mode for three dual tasks. The dependent variables were user preference and task completion time. The independent variable in the first experiment was the type of modes (i.e., Touch, Pen, or Voice) while the variable in the second experiment was the type of tasks (i.e., internet searching, subway map, memo, gallery, and application store). Results: In the first experiment, there was no difference between the uses of pen and touch devices. However, a specific mode type was preferred depending on the functional characteristics of the tasks. In the second experiment, analysis of results showed that user preference depended on the order and combination of modes. Even with the transition of modes, users preferred the use of multi-modes including voice. Conclusion: The order of combination of modes may affect the usability of multi-modes. Therefore, when designing a multi-modal system, the fact that there are frequent transitions between various mobile contents in different modes should be properly considered. Application: It may be utilized as a user-centered design guideline for mobile multi modal UI system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.1C
• /
• pp.113-122
• /
• 2010

In this paper, we propose a CP (Cyclic Prefix) detection based SSS (Secondary Synchronization Signal) detection method for initial cell search in 3GPP LTE (3rd Generation Partnership Project Long Term Evolution) FDD/TDD (Frequency Division Duplex/Time Division Duplex) dual mode downlink receiver. In general, a blind coherent SSS detection method which can detect SSS without CP detection is applied. However, coherent detection method caused performance degradation by channel compensation error at high speed environment because it uses estimated CFR (Channel Frequency Response) at PSS (Primary Synchronization Signal), and it can be more serious problem in TDD mode due to increased distance between PSS and SSS. Also blind detectionhas the drawback of high computational complexity. Therefore, we proposed a CP type pre-decision structure with non-coherent SSS detection which has stable operation in high speed channel environments for 3GPP LTE TDD mode as well as FDD mode, and can reduce computational complexity by applying CP detection before SSS detection. Simulation results show that the proposed method has stable operation for 3GPP LTE TDD/FDD dual mode downlink receiver in various channel environments.

• Journal of IKEEE
• /
• v.19 no.3
• /
• pp.424-430
• /
• 2015

This paper proposes an optical cryptography application to 2-D page-oriented data based on CFB(Cipher Feedback) mode algorithm. The proposed method uses a free-space optical interconnected dual-encoding technique which performs XOR logic operations in order to implement 2-D page-oriented data encryption. The proposed method provides more enhanced cryptosystem with greater security strength than the conventional CFB block mode with 1-D encryption key due to the huge encryption key with 2-D arrayed page type. To verify the proposed method, encryption and decryption of 2-D page data and error analysis are carried out by computer simulations. The results show that the proposed CFB optical encryption system makes it possible to implement stronger cryptosystem with massive data processing and long encryption key compared to 1-D block method.