• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.9
• /
• pp.1285-1291
• /
• 2013

In this paper, a double circular ring monopole antenna for wideband applications is designed and fabricated. The proposed antenna is based on a planar monopole design, and composed of double circular ring of radiating patches and ground plane to obtain the wideband characteristics. To get the optimized parameters, we used the simulator, Ansoft's High Frequency Structure Simulator(HFSS) and found the parameters that effect antenna characteristics. Using the obtained parameters, the proposed antenna is fabricated. The fabricated antenna is measured at the operating frequencies, and the return loss coefficient, gain, and radiation patterns are determined. The results of measurement, -10dB impedance bandwidth, measured return loss is 4,530 MHz(2,510-7,040 MHz) and antenna peak and average gains for the frequencies are obtained 0.71~3.38 dBi, -3.85~0.3 dBi, respectively. In case of radiation patterns, the proposed antenna displays nearly omnidirectional radiation characteristics in the E-plane, and monopole-like radiation pattern characteristics in the H-plane.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.3B
• /
• pp.183-190
• /
• 2003

The explosion of the Internet has brought an acute need for efficient operation, which becomes to develop several technologies based on optical networks. By matching merging technology using wavelength multiplexing, an efficient administration with limited wavelength can provide scalability of network. The merging in optical layer has limitation of devices since the merging can not be performed in this layer. Hence the merging must be implemented in electronic layer. When the merging is implemented, the delay time would be increased in OXC (Optical Cross Connection), but the improvement of throughput rate will be expected in the process of explosive traffic due to reduction of optical channel supporting large bandwidth. In this thesis, we proposed an OXC of dual module having a merging function. We considered the optimum merging point with the largest in system performance and confirmed results using the simulation.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.6
• /
• pp.522-528
• /
• 2017

In this paper, we propose a multi-band antenna for wearable devices using metal frame coupling. The proposed antenna has a $45mm{\times}35mm$ antenna using metal frame and a ground dual coupling structure. The proposed multi-band antenna in this paper is optimized for small devices such as wearable devices. By using the metal frame as a part of the antenna, the volume of the antenna is reduced and satisfies under VSWR 3:1 impedance bandwidth of 70 MHz (870 ~ 940 MHz) in low frequency band, 280 MHz (1600 ~ 1880 MHz) and 280 MHz (1900 ~ 2170 MHz) in high frequency band. It also verified the applicability of wearable devices by measuring wireless performance indicators such as TRP/TIS.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.2
• /
• pp.268-275
• /
• 2014

In this paper, a dual-band circular ring monopole antenna with stub and ground slot for WLAN(Wireless Local Area Networks)/WiMAX(World interoperability for Microwave Access) applications. The proposed antenna is based on a planar monopole design, and composed of one circular ring of radiating patch, cross strip in circular ring, modified feed line, and two rectangular slot in the ground plane for triple-band operation. To obtain the optimized parameters, we used the simulator, Ansoft's High Frequency Structure Simulator(HFSS) and found the parameters that greatly effect antenna characteristics. Using the obtained parameters, the antenna is fabricated. The numerical and experiment results demonstrated that the proposed antenna satisfied the -10 dB impedance bandwidth requirement while simultaneously covering the WLAN and WiMAX bands. And characteristics of gain and radiation patterns are determined for WLAN/WiMAX application.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.6
• /
• pp.610-618
• /
• 2021

In this paper, a photonic-based microwave system technology is described, and a traveling-wave electro-optic modulator is designed and manufactured as a key component. The fabricated modulator is composed of a metal diffusion waveguide for optical transmission and a planar waveguide electrode on lithium niobate substrate for microwave transmission. The electro-optic response bandwidth of I and Q channels in a fabricated dual parallel Mach-Zehnder modulator were measured for 27.67 and 28.11 GHz, respectively. Photonic four times up-converted X-band frequency and linear frequency modulated signal were confirmed using the fabricated electro-optic modulator by S-band input signal. The confirmed broadband signal can be applied to a microwave system for surveillance and high-resolution ISAR imaging.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.5
• /
• pp.373-379
• /
• 2019

If two signals with the same single-tone frequency and differing phases impinge simultaneously on an antenna at slightly differing angles, then a large error in the angle estimation might occur if the phase difference is either $0^{\circ}$ or $180^{\circ}$. This phenomenon might arise with an airborne fire-control radar, which has a relatively small bandwidth, for a low-flying target over the sea or terrain surface. In this paper, we show that the $Cram{\acute{e}}r$-Rao lower bound for such a target can be significantly lowered with the use of two frequencies.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.917-924
• /
• 2019

This paper presents a wideband low noise amplifier (LNA) that is suitable for LTE-Advanced and 5G communication standards employing carrier aggregation (CA). The proposed LNA encompasses a common input stage and a dual output second stage with a buffer at each distinct output. This architecture is targeted to operate in both intra-band (contiguous and non-contiguous) and inter-band CA. In the proposed design, the input and second stages employ a gm enhancement with resistive feedback technique to achieve self-biasing, enhanced gain, wide bandwidth as well as reduced noise figure of the proposed LNA. An up/down power controller controls the single input single out (SISO) and single input multiple outputs (SIMO) modes of operation for inter-band and intra-band operations. The proposed LNA is designed with a 45nm CMOS technology. For SISO mode of operation, the LNA operates from 0.52GHz to 4.29GHz with a maximum power gain of 17.77dB, 2.88dB minimum noise figure and input (output) matching performance better than -10dB. For SIMO mode of operation, the proposed LNA operates from 0.52GHz to 4.44GHz with a maximum voltage gain of 18.30dB, a minimum noise figure of 2.82dB with equally good matching performance. An $IIP_3$ value of -6.7dBm is achieved in both SISO and SIMO operations. with a maximum current of 42mA consumed (LNA+buffer in SIMO operation) from a 1.2V supply.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.22 no.1
• /
• pp.81-91
• /
• 2012

Presently in 2011, there are countless attacking tools oriented to invading security on the internet. And most of the tools are possible to conduct the actual invasion. Also, as the program sources attacking the weaknesses of PS3 were released in 2010 and also various sources for attacking agents and attacking tools such as Stuxnet Source Code were released in 2011, the part for defense has the greatest burden; however, it can be also a chance for the defensive part to suggest and develop methods to defense identical or similar patterned attacking by analyzing attacking sources. As a way to cope with such attacking, this study divides the network areas targeted for attack based on load balancing by the approach gateways and communication lines according to the defensive policies by attacking types and also suggests methods to multiply communication lines. The result of this paper will be provided as practical data to realize defensive policies based on high hardware performances through enhancing the price competitiveness of hardware infrastructure with 2010 as a start.

• Journal of Multimedia Information System
• /
• v.9 no.2
• /
• pp.145-154
• /
• 2022

The authors are making a prototype flexible board of a radio-frequency transmitter for measuring an electromyogram (EMG) of a flying moth and plan to apply for an experimental station license from the Ministry of Internal Affairs and Communications of Japan in the summer of 2022. The goal is to create a continuous low-dose exposure standard that incorporates scientific and physiological functional assessments to replace the current standard based on lethal dose 50. This paper describes the technical evaluation of the hardware. The signal of a bipolar EMG electrode is amplified by an operational amplifier. This potential is added to a voltage-controlled crystal oscillator (27 MHz, bandwidth: 4 kHz), frequency-converted, and transmitted from an antenna about 10 cm long (diameter: 0.03 mm). The power source is a 1.55-V wristwatch battery that has a total weight of about 0.3 g (one dry battery and analog circuit) and an expected operating time of 20 minutes. The output power is -7 dBm and the effective isotropic radiated power is -40 dBm. The signal is received by a dual-whip antenna (2.15 dBi) at a distance of about 100 m from the moth. The link margin of the communication circuit is above 30 dB within 100 m. The concepts of this hardware and the measurement data are presented in this paper. This will be the first biological data transmission from a moth with an official license. In future, this telemetry system will improve the detection of physiological abnormalities of moths.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.2
• /
• pp.119-125
• /
• 2022

In this paper, we present design, implementation and test results of CTM (Chirp Transceiver Module) EM (Engineering Model) for C-Band SAR (Synthetic Aperture Radar) Payload. The CTM is designed to operate dual frequency scan method that simultaneously operate two frequencies in each 50MHz bandwidth to achieve 120Km swath with 10m resolution at about 500Km altitude. The CTM used radiation tolerant RTG4 FPGA for space environment, and implemented with the Parallel DDS (PDDS) method which uses a small memory capacity compared to the memory-map method. Test results show high purity chirp signal generation and excellent IRF performance from received chirp signal after direct digital conversion.