• Journal of Animal Environmental Science
• /
• v.8 no.3
• /
• pp.177-182
• /
• 2002

Drying process is very important for commercialization of velvet antlers. So far, artificial drying has mostly depended on experience of farmers resulting in low efficiency of drying, deterioration during drying, and contamination by dust and bacteria. Various drying techniques for high-quality production have currently been commercialized in some developed countries, and one of them is a drying technique using microwave. In this study, application of the technique using an electronic (microwave) oven for drying of velvet antler was investigated. The results of this study are as follows. 1. It was found that the drying period was significantly affected by cornification of velvet antlers. Accordingly, it can be assumed that the velvet antlers should partly be sliced to save drying period and required drying energy. 2. It was also found that the drying speed was changeable according to tempering period and even with same drying period. The tempering period should be controlled according to processing rate. 3. The results indicated that a repeated drying of 2-min drying and 3-min tempering is the most effective when a microwave oven was used. 4. The results also showed that the drying technique using microwave of electronic oven can be effectively used for drying of velvet antlers. 5. Only drying and tempering periods were examined in this study, however, ingredient change of deer antler after drying is necessary to be investigated in the future.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.5
• /
• pp.5-12
• /
• 2011

Water content is one of the significant engineering properties of soil for predicting the behavior of soil matrix. Conventional drying oven can be widely used to obtain the values by drying the soil specimens for 16 to 24 hours at $105^{\circ}C$. Although a number of experimental data has been accumulated for the conventional method of drying soil for water contents, shortcomings of the method are still hard to overcome such as long drying time for in situ use and the difficulty of taking prompt actions against emergency cases. Recently, ASTM and JGS have established microwave oven drying techniques for obtaining water contents to cope with those problems. And the reliability evaluation study has been also performed on the microwave oven drying for water contents. Feasibility study of the microwave oven drying was performed to confirm the process of the technique with Jumunjin sand, kaolinite, bentonite, weathered granite soil, and organic soil. Investigation was also conducted on the factors affecting and enhancing the reliability of the technique.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.59-60
• /
• 2021

The unit-water content has a major problem in concrete structures which leads to micro cracks on the concrete during drying time. Thus, the compressive strength and durability of the concrete structures are significantly reduced. Several techniques have been developed to measure the unit-water content in concrete structures such as heating drying, unit volume mass, and capacitance measurements. However, these techniques have problems in during measurement such as longer time, expensive and difficult in analysis of data. Frequency Domain Reflectivity (FDR) is one of the sensors which used to measure the water content. This method has several advantages including easy to measure, inexpensive, and capable of measuring moisture in real time. In this study, an attempt has been made to evaluate the unit-water content in concrete using the FDR sensor and interpret the data with deep learning method.

• Journal of Biosystems Engineering
• /
• v.3 no.2
• /
• pp.100-113
• /
• 1978

Drying grain with conventional artificial drying methods requires great quantities of petroleum fuels. Depletion of fossil fuel increases the need of the utilization of solar energy as an alternative to petroluem fuels for drying grain , an energy intensive agricultural operation. Many techniques for the utilization of solar energy in grain drying have been developed, however, there are many problems in adopting solar energy as an energy sources for drying grain. Futhermore, very little research has been done on solar grain drying in Korea. This study was conducted to evaluate the availability of solar energy for drying of rough rice in Chuncheon, Suweon, and Jinju areas based on 50year meteorological data, and to analyze experimentally the performance of a solar air collector for dying grain, and to find the effects of solar heated air compared to unheated air on the rate of drying and energy consumption required for drying of rough rice. The results of this study was may be summarized as follows ; 1. Monthly average daily total radiation on a horizontal surface in October was 260.6 ly/day for Chuncheon, 240.3 ly/day for Suweon , and 253.4 ly/day for Jinju area, respectively. 2. the ratio of monthly average daily diffuse radiation to daily total radiation on a horizontal surface was approximately 0.41 for Chuncheon, 0.45 for Suweon, and 0.44 for Jinju area, respectively. 3. Although the statistical distribution curves of daily total radiation for the three locations were not identical , the differences among them were not large and may be neglected for many practical purposes. 4. I was estimated that the optimum tilting angle of the collector in October was approximately 46 degrees for Chuncheon and Suweon and 45 degrees for Jinju. 5. The ratio of the total radiation on a optimum tilting plane to that on a horizontal plane was estimated to be 1.36 for Chuncheon, 1.31 for Suweon, and 1.27 for Jinju , respectively. 6. The collection efficiency of the solar air collector ranged from 47. 8 to 51. 5 percent at the air flow rates of 251. 1-372.96 $m^3$/hr. High efficiency remained nearly , constant during the best sunshine hours, 10 a.m. to 2 p.m. and decreased during other hours. More energy was collected as the air flow rate incresed. 7. The average temperature rise in the drying air from the solar collector for the test period varied from $6.5^\circC$ to $21.8^\circC$ above the ambient air temperature. 8. Solar-dried rough rice averaged 13.7 percent moisture (w.b.) after 130 hours of drying with the air flow rate of 1. 64 ccm/$m^3$, and rough rice dried with natural air averaged 15.1 percent moisture (w.b.) after 325 hours of drying with the same air flow rate. 9. Energy saving of 2.4 kwh per $m^3$ percentage point of moisture removed was obtained from solar heated air drYing. The solar bin used 53.3 percent less energy per percentage point of moisture removed than the natural air bin.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.4
• /
• pp.16-24
• /
• 2001

Conventional hot-air oven-drying method takes at least four hours to determine the moisture content of wood sample and this method is not always acceptable to wood industry. In this study samples of six different specifications from Paulownia coreana, Pinus densiflora and Quercus acutissima were dried in domestic microwave oven to their oven dry weights to investigate the possibility of rapid moisture content determination technique using microwave-oven drying method. Continuous heating time, cooling time and intermittent heating time were determined by each species and sample specifications. Temperatures of surface and center of samples were also measured during drying. Oven-drying times were reduced to 1/7~1/10 of conventional hot-air oven-drying method. Therefore microwave heating and drying techniques appear attractive for wood industry as a rapid moisture content determination method.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.12
• /
• pp.867-874
• /
• 2012

In the present study, three-dimensional transient numerical simulations were carried out to improve the performance of a vehicle paint drying process. In order to describe the movement of a vehicle, the techniques of moving boundary condition and multiple reference flames (MRF) were used. For the validation of the numerical analysis, the predicted temperature on the surface of a vehicle was compared to the experimental data, and a good agreement was achieved. With validated numerical procedure, various operating conditions of the temperature and the flow rate of the supply air were investigated to improve the drying performance of the facility. It is shown that the optimization of the operating condition can lead to energy savings and faster line speed of the production.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.4
• /
• pp.1218-1220
• /
• 2014

• Food Science of Animal Resources
• /
• v.38 no.2
• /
• pp.224-239
• /
• 2018

In this study, the possible changes in the quality characteristics of pastirma, Turkish-type dry-cured meat product, produced by using two different salts (NaCl-KCl) in a curing mixture and two different production techniques (natural and controlled condition) were examined. Moisture, pH, salt, sodium, potassium, TBA, fat, water activity, instrumental colour, texture, and sensory analyses were implemented in order to determine the possible effects of these applications. Fat, aw, pH, colour, tiobarbituric acid (TBA), texture, salt, Na and K values may allow these desired modifications in pastirma production to be limited. The substitution of 15% KCl instead of NaCl was acceptable in terms of the sensorial properties of the pastirma. However, the sensory analyses did not allow for using a higher KCl instead of NaCl because both the hardness and chewiness in the texture of the pastirma samples salted with 30% of KCl were not scored positively. Besides this, negative effects, which may occur during the pastirma production under natural conditions, can be eliminated by the production being under controlled conditions.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1323-1328
• /
• 2004

This paper shows the study on the design of the spray-freeze dryer for the production of the pulmonary inhalation powders. Powder production and handling has been an integral part of pharmaceutical processing because of the wide use of oral dosage forms. There are a few commonly used powder preparation methods including mechanical milling, precipitaion, spray drying, freeze drying, and so on. In general, methods available for preparing inhalation powders are limited due to certain inhalation powder's sensitive nature to the processing environments. This is particularly true for preparing dry powder aerosols where the aerodynamic particle size$(<5{\mu}m)$ and the size distribution are pivotal. Supercritical fluid antisolvent and spray freeze drying have recently emerged as promising techniques for producing powders for use in microcapsulation. However, the aerosol applications of these powders are yet to be explored. The purpose of this study is to test the feasibility of using spray freeze-dried pulmonary inhalation powders for aerosolization.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.11a
• /
• pp.1-6
• /
• 2004

This paper shows the study on the design and another applications of the spray-freeze dryer for the production of valuable material powders. Powder production and handling has been an integral part of material extracting processing and pharmaceutical processing because of the wide use of oral dosage forms. There are a few commonly used powder preparation methods including mechanical milling, precipitaion, spray drying, freeze drying, and so on. In general, methods available for preparing inhalation powders are limited due to certain inhalation powder's sensitive nature to the processing environments. This is particularly true for preparing dry powder aerosols where the aerodynamic particle size($<5{\mu}m$) and the size distribution are pivotal. Supercritical fluid antisolvent and spray freeze drying have recently emerged as promising techniques for producing powders for use in microcapsulation. However, the aerosol applications of these powders are yet to be explored. The purpose of this study is to test the feasibility of using spray freeze-dried valuable material powders for aerosolization.