• Journal of the Korean Society of Industry Convergence
• /
• v.16 no.1
• /
• pp.1-8
• /
• 2013

In case that W/B is 20%, 30%, 40% respectively, the effects of additive and shrinkage reducing agent on the autogenous shrinkage for high strengthen concrete through the substitution of FA and SF analysis were obtained as following conclusions. When the ratio of FA increased, the compressive strength of high strengthen concrete is decreased in the early times. As the ratio of SF increase, the compressive strength also increased. Comparing with PC(Portland Cement) for 7 days curing, the strength is 13.8% of FA10 + SR0.5 and 19.2% of FA15 + SR0.5 decreased when W/B is 20%, and 6.1% of SF7.5 + SR0.5, 4.8% of SF15 + SR0.5, the strength are increased. In case that W/B is 30%, 13.1% of FA10 + SR0.5 19.1% of FA15 + SR0.5 the strength is decreased and 4.1% of SF 7.5 + SR0.5, 7.2% of SF15 + SR0.5 the strength are increased. In case of W/B 40%, 4.3% of FA10 + SR0.5, and 8.7% of FA15 + SR0.5, the strength is decreased and 3.3% of SF7.5 + SR0.5, 6.3% SF15 + SR0.5 the strength is increased. When the ratio of SR is 0.5%, autogenous shrinkage strain of OPC concrete appeared $-417{\times}10-6$ in 56days curing, the shrinkage strain is decreased 23.7%. The reducing effects of autogenous shrinkage when the mineral and shrinkage agent are used are the same as ones when only shrinkage agent used.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.1
• /
• pp.101-110
• /
• 2014

Expansion agent is a very effective admixture for prevention of cracking due to autogenous/drying shrinkage and this can induce internal chemical prestress to embedded reinforcement. In this paper, tension-softening and hardening in cement mortar with steel and CSA expansion agent are experimentally evaluated. Cement mortar with steel reinforcement is prepared and tensile strength test is performed for evaluation of cracking and tensile behavior. In spite of slightly reduced strength and elasticity in CSA mortar, significantly increased tension-hardening behavior is evaluated in CSA mortar with induced chemical prestress. Furthermore previous tension softening models are compared with the test results and improvement are proposed.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.18 no.4
• /
• pp.323-328
• /
• 1998

A field experiment was carried out to determine the effects of chemical and mechanical treatment at mowing on the field drying rate and hay quality of autumn oat (Avena sativa L.). The chemical drying agent/mower conditioner ($K_2CO_3$ 2%, conditioning, $K_2CO_3$ 2% + conditioning and control) were treated at different harvest stages (late boot, heading and bloom stage) for hastening hay manufacture in the autumn of 1996. After field dry, square bales were made by hay baler, and the dry matter(DM) loss and visual estimation of oat hay were evaluated after storing two months. In general, the field drying rate of oat was slow, regardless of harvest stage. Mechanical and chemical + mechanical treatment were effective, but the effectiveness of chemical alone was very low. With mower conditioning, the duration of field dry was shortened by 2 days compared with control. The DM loss of hay was higher at boot stage(51.4%) than at heading stage (21.1%), and the DM loss was reduced by mechanical and chemical + mechanical combined treatment. The visual score (leafiness, green color, odor and softness) of hay after storing was high in mechanical and chemical + mechanical, but the score by chemical alone was very low. The nutritive value (ADF, NDF, digestibility, and relative feed value) of hay was also high with treatment of mechanical and chemical + mechanical, but the quality by chemical alone was similar compared with control. In conclusion, mower conditioning can enhance the field drying rate of autumn oat, but the drying efficiency of the chemical drying agent was very low. However, it is suggested that hay-making of oat in autumn is very hard though using mower conditioner.

• Journal of Life Science
• /
• v.12 no.6
• /
• pp.745-751
• /
• 2002

Several bacterial strains producing biosurfactants were isolated from polluted marine and soil by oil. One of the strains named LSC11 showed strong production activity of biosurfactants. This strain was identified as a Bacillus sp. LSC11 based on the morphological, biochemical, and physiological characteristics. The biosurfactant, produced by the strain, emulsified crude oil, vegetable oil, and hydrocarbons. The surface tension of the culture broth of Bacillus sp. LSC11 decreased to 32 mN/m. The crude biosurfactant was obtained from the culture broth by acid precipitation, freeze drying, solvent extraction, and evaporation. The emulsifying activity of the biosurfactant showed better than the chemically synthesized surfactant (SDS, Span40, Span 85). The biosurfactants had strong properties as an emulsifying agent and as an emulsion-stabilizing agent.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.43 no.4
• /
• pp.76-81
• /
• 2011

This study was carried out in order to develop a speciality functional coated paper, which can be recognized under a ultraviolet lamp. The special fluorescent whitening agent (FWA) which absorbs ultraviolet light (397~410 nm) and emits it as yellowish light (570~500nm) was used. The special FWA was applied in a coating color in two ways: (1) direct application to a coating color as a FWA; (2) application on pigment surface, drying it and application it as a fluorescence whitening pigments (colored pigments). The effects of the special FWA on coating color properties were tested and the distribution of colored pigments in coated paper was evaluated under a ultraviolet lamp. The results showed that the colored pigments didn't affect on coating color properties. Experimental results showed the possibility of producing a security coated paper using the special FWA. To produce a speciality functional paper, it was found to be proper to apply the special FWA in the form of colored pigment.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.142-143
• /
• 2014

In this study, as to enhance the efficiency and workability, binder contained 3 types of gels have been used to replacement the OPC. Fundamental properties and length change of the concrete have been tested to evaluate the effect of different binders. The following results could be made as the conclusion. When the binder contained 3 types of gels used, the flowability increased, whereas the air content decreased. There showed some different air content when the component of binder changed but the difference was consider as limit. For the strength properties, with the using of binder contained 3 types of gels increased the strength. Specimen of FA20SF5 showed the better strength and lower length change of drying shrinkage than other specimens.

• KSBB Journal
• /
• v.31 no.4
• /
• pp.291-299
• /
• 2016

In this study, Indomethacin, the poorly water soluble drug, was selected and prepared dispersing oral disintegrating films according to the molecular weight of polyethylene glycol (PEG) which are sort of dispersing agents. Also the molecular weight and content of PEG were evaluated effect on the degree of dispersion, physical property and dissolution when making oral dispersing film containing indomethacin to find appropriate condition and suggested guidelines of making oral dispersing film. The appropriate dispersing ratio of the amount of surfactants and dispersing agent were 1% and 4%, also the stability dropped in the PEG molecular weight of 4000 or more. Drying time of oral dispersing film was $90^{\circ}C$ for 10 minutes to 12 minutes that dispersing film's property about flexibility, detachability were very good. The oral dispersion film's content used PEG 400 was $98.6{\pm}0.5%$ and the most uniform. As the molecular weight of PEG increased, dissolution time also increased. On the basis of evaluation parameter, PEG with 400~600 of molecular weight was selected as good dispersing agent in oral dispersing film. Therefore, it can be suggested guideline of preparation application study in oral dispersing film.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.4
• /
• pp.174-177
• /
• 2010

We have developed an environment-friendly etching process, an alternative to the dichromic acid etching process, as a pretreatment of acrylonitrile-butadiene-styrene (ABS) plastic for electroless plating. In order to plate ABS plastic in an electroless way, there should be fine holes on the surface of the ABS plastic to enhance mechanically the adhesion strength between the plastic surface and the plate. To make these holes, the surface was coated uniformly with dispersed chemical foaming agents in a mixture of environmentally friendly dispersant and solvent by the methods of dipping or direct application. The solvent seeps into just below the surface and distributes the chemical foaming agents uniformly beneath the surface. After drying off the surface, the surface was heated at a temperature well below the glass transition temperature of ABS plastic. By pyrolysis, the chemical foaming agents made fine holes on the surface. In order to discover optimum conditions for the formation of fine holes, the mixing ratio of the solvent, the dispersant and the chemical foaming agent were controlled. After the etching process, the surface was plated with nickel. We tested the adhesion strength between the ABS plastic and nickel plate by the cross-cutting method. The surface morphologies of the ABS plastic before and after the etching process were observed by means of a scanning electron microscope.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1165-1166
• /
• 2006

An experiment was carried out to investigate the effect of Ba Stearate as a reducing agent on the magnetic and physical properties of anisotropic $BaFe_2-W$ type ferrite magnets. It was found that the magnetic properties of $BaO{\cdot}8.5Fe_2O_3$ were improved by adding 0.3 wt% of Ba Stearate, 0.5 wt% of $SiO_2$, and 0.5 wt% of CaO together. The optimum conditions for making magnets were as follows; semisintering condition: $1350^{\circ}C{\times}4.0$ h in nitrogen gas atmosphere, drying condition: $180^{\circ}C{\times}2.0$ h in air, sintering condition: $1160^{\circ}C{\times}1.5$ h in nitrogen gas atmosphere. Magnetic and physical properties of a typical sample were $J_m$ = 0.46 T, $J_r$ = 0.43 T, $H_{cJ}$ = 182.3 kA/m, $H_{cB}$ = 177.2 kA/m, $(BH)_{max}$ = 33.8 kJ/$m^3$, $T_C$ = $495^{\circ}C$ and $K_A$ = $2.65{\times}10^5\;J/m^3$ and $H_A$ = 1332 kA/m.

• Journal of Sericultural and Entomological Science
• /
• v.15 no.1
• /
• pp.37-48
• /
• 1973

The purpose of this studies is to improve the cohesion of raw silk through various analyses on cocoon drying, cooking, reeling, re-reeling, and on the properties of water. Also we investigated the correlation between silk testing items which we have reached to the following results. 1. Drying of cocoon When cocoons were slowly dried with 100$^{\circ}C$, the results of cohesion became much better. On the other hand, the results were considerably decreased in case the temperature with 115$^{\circ}C$. 2. Cooking of cocoon In case of the cooking of cocoon, we found that the result of cohesion was best with incomplete cooking, that of the control was next, while in over cooking, the results were very low. Also the results of cohesion were much better when using the method of over cooking with sericin arrestive agent than that of incomplete cooking with sericin agglutinating agent. 3. Reeling of cocoon A) When the temperature of reeling bath was 25-45$^{\circ}C$, the results of cohesion test were much better, but at the temperature below 25$^{\circ}C$ or above 45$^{\circ}C$, the results became worse. B) With out the process of croissieur, the results of cohesion were too bad, but in case of croissieur more than 1cm, cohesion became better rapidly. Further more, we understood that the results of cohesion were improving slightly with longer length of croissieur. C) When the velocity of reeling was increased, the results of cohesion also improved. The best results were shown when reeling velocity was 180-220 r.p.m. But when the velocity was increased more than 220 r.p.m., the results of cohesion got worse more or less. D) When the temperature of the drying pipe in reeling machine was raised, the results of cohesion also showed a tendency to improve. 4. Re-reeling A) We could net reach a conclusion as to have correlation between the number of dipping repeat in vacuum tank and the results of cohesion before re-reeling process. B) When we used Seracol 500 as an agglutination protective agent with l/1000 to l/2000 of water, the results of cohesion test were better. C) When we used Pearl-lite as an agglutination protective agent with 1/1000 to 1/2000 of water, the results of cohesion were considerably better. D) We gained tile best results when used Cohesion Improving Chemical, A-80, with 500-1500 times diluted. 1) Results of cohesion was improved when humidity was low or temperature was high in the rereeling machine. 5. Filature water A) The water pH near the isoelectric point of protein showed the best cohesion, but the farther water pH, the worser results were obtained. B) With the increasing of M-alkalinity in filature water, the results of cohesion were worse. Above all, we understood the tendency of the results of cohesion get worse when the M-alkalinity is increased above 200 ppm. C) By increasing the total hardness of the filature water, it improved the results of cohesion. Especially, when the total hardness was above 300ppm, the results were extremely high. 6. Effects combination of each results A) The result of effects combination in filature processes with the obtained best conditions was distinctively improved. But the results could not reach in mathematicaly double effect. When reelied under worse conditions, the results of cohesion test were too bad. There was "effect limit" for the promotion. B) Generally the results of cohesion were bad when the filature conditions(the temperature, pressure and the properties of water, etc) are processed as sericin loss to be high. On the other hand, the results were very good when lower sericin loss was controlled in filature conditions. C) When filature conditions such as reeling velocity and croissieur length provide pysical cohesion ability and when raw silk dry fast during reeling and re-reeling, we found the result of cohesion was better. 7. Correlation of silk testing items. A) A negative correlation exists between the results of cohesion test and cleanness defect. Another word, the result of cohesion test was found to be worse as cleanness defect increased. B) In cleanness, cohesion has negative correlation against the number of slugs, but we could not find any correlation against long loops, loose ends. C) Cohesion has negative correlation against average neatness and low neatness defect. The better the results of neatness respectively, the better the results of cohesion found. D) There is no correlation between tenacity and the results of cohesion test, but there was high positive correlation between the results of elongation and those of cohesion test. The more elongation, the better the results of cohesion was found.