• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.183-188
• /
• 2009

RFID method is a non-contact automatic identification technology, which attaches microchips and antennas to an object in a tag form, to send and process information sent to the network using wireless frequency. Drying and curing process is extremely important which minimizes the resistivity of RFID antennas. This research is about the drying characteristic of conductivity ink, and analyzes and compares the hot-air drying process and infrared drying process. Also, the research was done for the improvement in drying performance by using combined process of hot-air and infrared mechanism. The experiment result shows that the hot-air or infrared drying system used alone cannot meet the required performance in drying printing method using conductivity ink. The combined drying system of hot-air and infrared ray showed resistance low enough in short drying and curing time, and this mechanism makes drying and curing process for mass and continuous production possible on-line.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.2
• /
• pp.103-108
• /
• 2003

This study was performed to find out drying characteristics and develop waste heat recovery dryer. this system was initiated in order to recover discharged waste heat of drying air from drying chamber in agricultural products dryer and recycle for additional heat source that could save drying cost. The system consists of drying chamber, fan, burner, circulation pump and heat exchanger made of fins and tubes. For the system performance, drying experiments with fresh pepper were conducted, and comparisons on fuel consumption amount and drying performance were made between conventional dryer and the heat recovery system attached dryer.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.4
• /
• pp.44-48
• /
• 2021

Semiconductor inspection equipment makes components using materials with insulating properties for functional inspection including current and voltage of semiconductor parts. A representative insulating material is plastic, and plastic is made of a component through an injection process using plastic pellet. When plastic pellets contain excessive moisture, problems such as performance degradation and product surface defects occur. To prevent this, pre-drying is essential, and the heat convective type is the most applied. However, the heat convective type has a problem of low consumption efficiency and a long drying time. Recently, many studies have been conducted on a drying method using microwaves due to high energy efficiency. In this paper, drying was performed using a microwave for drying PC pellets. Energy consumption and drying efficiency analyzed by set up an experimental apparatus of heat convective, microwave, and hybrid(heat convective + microwave) types. It was confirmed that energy consumption and drying efficiency were high when drying using microwaves, and it was confirmed that the hybrid method improved drying performance compared to the heat convective method. It is expected that the research results of this paper can be used as basic data for drying plastic pellets using microwave.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.6 s.249
• /
• pp.734-740
• /
• 2006

The purpose of this study is to develop and commercialize a paddle-type fluidized dryer. The drying system used in this study, was designed to attach a paddle-type fluidized mixer to a dryer. The drying system is based on the drying method to generate thermal contacts, as fluidized layers are generated due to a paddle mechanism. Accordingly, the time of drying is short and material damage is very little. Also, the drying system operates as a closer system so it can be utilized not only for food and chemical materials, but also for environmental pollution materials. According to its performance test, the drying system is possible to dry low-moisture contents and its drying performance is outstanding. In conclusion, the drying system designed for this study, is likely to have great potential for commercialization.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.21 no.1
• /
• pp.1-8
• /
• 2009

The simulation of a heat pump dryer has been carried out to figure out the effect of air flow rate on the drying performance represented by MER, SMER, and so on. The simulation includes the analyses of one-stage heat pump cycle and simple drying process using the drying efficiency. The heat pump cycle with Refrigerant 134a has been considered. In the dryer, some of drying air from the drying chamber flows through the heat pump system, the rest of air bypasses the heat pump system. The two air flows joins before the drying chamber inlet. The performance parameters considered in the present study are MER, SMER, the temperature and humidity of drying air. Those parameters are compared for different total air flow rate or bypass air flow rate.

• Journal of Biosystems Engineering
• /
• v.25 no.2
• /
• pp.115-122
• /
• 2000

This study was performed to develop a prototype continuous flow ginseng dryer with which better product quality and lower drying energy consumption could be achieved compared with conventional ginseng dryers. A dryer having both far infrared ray (IR) and heated-air as the drying energy sources was designed and fabricated . Dryer performance was studied by examining energy efficiencies and dryer performance evaluation indices (DPEI) during the drying tests of medium-sized four year ginseng roots with IR radiating plate temperature and drying air temperature in the range of 80-12$0^{\circ}C$ and 22-5$0^{\circ}C$, respectively. The DPEI of IR /heated -air combined drying was 1/3 of that of the conventional heated-air drying when ginseng were dried to the same final moisture ratio. When ginsengs were dried for 12 hours in the prototype IR/heated-air combination dryer, a linear relationship was found to exist between final moisture ratio and ginseng temperature. As the drying progressed, drying air temperature inside the dryer was nearly constant but ginseng temperature was drastically increased during the first two hours and gradually increased thereafter until the end of drying. With the prototype Ir/heated-air combination dryer, the drying rate changed little but the energy efficiency increased proportionally when the amount of ginseng to be dried increased. Drying capacity, energy efficiency, and DPEI of the prototype IR/heated-air combination ginseng dryer were estimated to 1.500 roots, 65% and 3.800kJ/kg-water , respectively.

• Journal of Biosystems Engineering
• /
• v.34 no.5
• /
• pp.358-362
• /
• 2009

This study was conducted to evaluate the performance of a 12 tons capacity circulating concurrent flow rice dryer. An actual scale dryer with the capacity of 12 tons was developed to obtain a faster drying rate of 0.8~1.2%(w.b.)/h, while maintaining a lower drying energy consumption of 5,000 kJ/kg-water and achieving a drying quality that was comparable to a conventional cross-flow rice dryer. The Test-1 was conducted at $110^{\circ}C\;-\;20\;cmm/m^2$ and the Test-2 was conducted at $120-110-100-90^{\circ}C\;-\;20\;cmm/m^2$ under the same conditions as Test-1. In Test-1, the drying rate, drying energy consumption and crack ratio were 0.98 %(w.b.)/h, 4,573 kJ/kg-water and 3.2%, respectively. In Test-2, the drying rate, drying energy consumption and crack ratio were 0.74 %(w.b.)/h, 4,790 kJ/kg-water and 4.0%, respectively. The results of these tests demonstrated that this concurrent-flow dryer reached the desired drying rate, drying energy consumption and crack ratio.

• Journal of Biosystems Engineering
• /
• v.6 no.2
• /
• pp.48-57
• /
• 1982

In order to improve the quality of traditionally sun-dried red peppers and to increase the efficiency of drying performance, three types of solar dryers were designed and built, and drying performance of the solar dryers was compared to traditional sun drying. Results obtained from the experiment are summarized as fallows: 1. The air temperature and relative humidity profiles over a 8-hour period measured at the specified locations in the drying chamber of solar dryers appeared to have large variation in each dryer. The rate of drying increased with the temperature rise in the drying chamber of the solar dryer. 2. In general. drying with solar dryers proceeded faster than traditional sun drying. With A'-type of solar dryer developed in the second experiment it was possible to dry red peppers in seven days from an initial moisture content of 80% to safe storage conditions. The drying time with the A'-type solar drier was 50% shorter compared to traditional sun drying. 3. Red peppers appeared to have an increasing or constant-rate drying period until the weight of the product was reduced to about one half the initial weight, followed by a falling-rate drying period. When the dried red peppers were exposed to the atmospere during the night, the moisture content increased as much as 6%, which is much higher than for the grains. 4. It was suggested from the experiment that either a heat storage system or a supplemental heating system in the solar dryer was desirable for more efficient drying operation. 5. It was shown that the solar dryer developed in this study may be suitable for drying other vegetables and fishes, and also offered additional advantages of saving in drying time, maintaining sanitation and minimizing contamination by dust, insects and unfavorable weather condition.

• Solar Energy
• /
• v.7 no.1
• /
• pp.14-22
• /
• 1987

This paper presents an experimental study of a solar drying system designed and installed by KIER. Experiments have been performed using the KIER system for the drying of marine products, such as squid. Presented in detail are the experimental observations of collector air temperature, solar intensity, absorber plate temperature, drying chamber temperature, humidity and other measures of drying chamber performance with variation of air mass flow rate. As a result, average temperature attained in the drying chamber during autumn weather has been adequated for drying of squids.

• Journal of Computational Design and Engineering
• /
• v.3 no.4
• /
• pp.398-413
• /
• 2016

This work describes the design and development of a new drying system for a rollover carwash machine with the support of numerical tools. The drying system is composed of a pair of stationary vertical dryers and a moveable horizontal dryer that can adjust itself to the contour of a vehicle. After the definition of the dryers' concept, their performance was assessed individually to check their internal flow pattern and to improve their airflow distribution. These issues are expected to provide feedback on redesign and geometric optimization of the dryers. After redesign of the dryers separately, the behaviour of the complete drying system was studied on actual vehicle models, representative of the shortest and tallest dimensions that can be washed with the existing carwash machine sector. The drying efficiency of the whole system was studied by calculation of shear stress distribution on various surfaces of a given vehicle. The results allowed concluding that the overall drying performance of the design system is very good and assure adequate drying on most vehicles surfaces. The results obtained from numerical studies were then validated with experimental measurements and a good agreement was found between the two. The procedure employed in this work can be applied to support the design and analysis of other mechanical drying systems.