• Asian-Australasian Journal of Animal Sciences
• /
• 제26권11호
• /
• pp.1553-1561
• /
• 2013

Forty-eight crossbred heifers ($378.1{\pm}18$ kg) were used in a 56-d feeding trial (four pens per treatment in a randomised complete block design) to evaluate the influence of ionophore supplementation on growth performance, dietary energetics and carcass characteristics in finishing cattle during a period of heat stress. Heifers were fed a diet based on steam-flaked corn (2.22 Mcal $NE_m/kg$) with and without an ionophore. Treatments were: i) control, no ionophore; ii) 30 mg/kg monensin sodium (RUM30); iii) 20 mg/kg lasalocid sodium (BOV20), and iv) 30 mg/kg lasalocid sodium (BOV30). Both dry matter intake (DMI) and climatic variables were measured daily and the temperature humidity index (THI) was estimated. The maximum THI during the study averaged 93, while the minimum was 70 (THI average = $79.2{\pm}2.3$). Compared to controls, monensin supplementation did not influence average daily gain, the estimated NE value of the diet, or observed-to-expected DMI, but tended (p = 0.07) to increase (4.8%) gain to feed. Compared to controls, the group fed BOV30 increased ($p{\leq}0.03$) daily gain (11.8%), gain to feed (8.3%), net energy of the diet (5%), and observed-to-expected DMI (5.2%). Daily weight gain was greater (7.6%, p = 0.05) for heifers fed BOV30 than for heifers fed MON30. Otherwise, differences between the two treatments in DMI, gain to feed, and dietary NE were not statistically significant (p>0.11). Plotting weekly intakes versus THI, observed intake of controls was greater (p<0.05) at THI values ${\leq}77$ than ionophore groups. When THI values were greater than 79, DMI of control and MON30 were not different (p = 0.42), although less than that of groups fed lasalocid (p = 0.04). Variation in energy intake was lower (p>0.05) in the ionophores group (CV = 1.7%) than in the control group (CV = 4.5%). Inclusion of ionophores in the diet resulted in relatively minor changes in carcass characteristics. It is concluded that ionophore supplementation did not exacerbate the decline of DM intake in heat-stressed cattle fed a high-energy finishing diet; on the contrary, it stabilised feed intake and favoured feed efficiency. Ionophore supplementation reduced estimated maintenance coefficients around 10% in finishing cattle during a period of heat stress. This effect was greatest for heifers supplemented with 30 mg lasalocid/kg of diet.

• 한국주조공학회지
• /
• 제14권6호
• /
• pp.548-557
• /
• 1994

Grey iron containing a small amount of Cu and Mo to improve the effect of heat treatment and microstructures were poured in to the mold and them austenized at $900^{\circ}C$. After austenitizing the specimens of castings were austempered $210^{\circ}C$, $250^{\circ}C$, $300^{\circ}C$ and $350^{\circ}C$. The effects of matrix structures, mechanical properties and wear characteristics were investigated by austempering temperatures. Tensile strength and hardness of austempered grey iron are increased and the amount of retained austenite is decreased as austempering temperature is lower even though the amount of retained autenite in it only 4%. The amount of rolling wear loss are increased as rolling revolution is increased and wear loss of austempered grey iron under dry rolling condition is characterized by three models; initial wear, stationary wear and abnormal wear. It has been found that the amount of wear loss was increased with increasing maxium compressive stress and rolling revolution.

• 한국대기환경학회지
• /
• 제26권3호
• /
• pp.286-297
• /
• 2010

This study deals with the effect of pretreatment on the $CO_2$ adsorption capacity of zeolitic adsorbents including a commercial A-type zeolite and cation exchanged adsorbents. The pre-heating could change the intrinsic properties such as specific surface area and adsorption capacity of the adsorbent. As a result of the experiment, the moisture previously filled inside might affect the potential adsorption capacity of the adsorbent, and could be disappeared throughout the heat treatment. An optimum pretreatment temperature for the test adsorbent was found to be $400^{\circ}C$, at which temperature enabled more than 90% refreshment. Precise examination through the TPD test showed that the TSA (Temperature Swing Adsorption) process would be desirable in dry adsorption of $CO_2$.

• 한국염색가공학회지
• /
• 제23권4호
• /
• pp.290-297
• /
• 2011

In this study, the possibility of the practical development of highly sensitive clothing textiles using fibrillated wool fibers were considered by determining the dyeability, the physical and mechanical properties of fibrillated wool fibers treated under strong acid and high temperature ultrasonic wave irradation and they were compared with those of untreated wool fibers. The color strengths of the dyed fibrillated wool fabrics increased by the acid metal complex dyes contrary to the untreated wool fabrics, and color fastness properties to rubbing, light, and dry cleaning were excellent, similar to those of the untreated wool fabrics. The tensile strengths of fibrillated wool fabrics were also kept after the dyeing. Moreover, the Numeri, Fukurami, and THV of the fibrillated wool fabrics were better than those of the untreated wool fabrics.

• 공업화학
• /
• 제8권5호
• /
• pp.811-815
• /
• 1997

본 연구에서는 고상반응에 의한 $YBa_2Cu_3O_{7-y}$계 고온 초전도체의 결정구조 및 초전도 특성에 미치는 원료분말의 분쇄효과를 명백히 할 목적으로 $Y_2O_3$, $BaCO_3$, CuO의 혼합물을 유성볼밀을 사용하여 건식혼합분쇄를 행하였다. 얻어진 분쇄산물의 비표면적은 60분 분쇄할 때까지 증가하며. 그 후 분쇄시간이 증가함에 따라 감소하는 경향을 보였다. 소결체의 임계온도는 분쇄시간에 의존하지 않고, 약 90K로 일정한 값을 나타내었다. 한편, 소결체의 임계전류밀도는 분쇄시간에 크게 의존하였으며, 60분 분쇄한 소결체에서 최대치 $150A/cm^2$를 나타내었다.

• KSBB Journal
• /
• 제19권4호
• /
• pp.245-249
• /
• 2004

천연 식품 소재로 널리 사용되는 효모 추출물을 제조하는 공정의 개선을 위하여 제빵용 효모를 이용하여 자기소화법과 효소처리법을 병용하여 효모 추출물을 제조하였다. NaCl과 에탄올이 효모의 자기소화에 영향을 미치는 인자이었으며 최적 첨가량은 각각 3%와 1%이었다. 효모의 열처리와 효모 세포벽 분해효소의 사용은 유의하지 않았다. 효모를 자기소화 시킨 후 단백질 분해효소와 핵산 분해효소를 처리하고 Maillard 반응과 debittering 공정을 거쳐 효모 추출물을 제조하였다. 최종적으로 얻어진 효모 추출물의 수율은 고형분 기준으로 76%, 총 질소 기준으로 59%이었다. 맥주 효모를 이용한 결과와 비교하면 제빵용 효모를 이용하는 것이 맥주 효모를 이용하는 것보다 수율면에서도 유리하였다.

• 펄프종이기술
• /
• 제42권3호
• /
• pp.58-66
• /
• 2010

The Annals of beeswax applied-Joseon Dynasty have some serious damages such as cracks, brown, red or black spots, and discolorations by chemical and biological degradation, but others without any beeswax application have still been keeping good quality during over several hundred years. It would be convinced that the beeswax applied in the Annals resulted in these deteriorations. Therefore, in order to focus on the aging mechanism and conservation techniques for the beeswax-applied Annals of Joseon Dynasty, the beeswax applying and dewaxing techniques of Hanji were tried by auto bar coater with a hot plate, and by heat-pressure sensitive extracting treatments. The ageing behaviors of beeswaxed Hanji and dewaxed Hanji were investigated by measuring the changes of physical, optical, morphological, and chemical properties, through accelerated ageing treatment in dry oven at $150^{\circ}C$ during 48 hours. Consequently, the ageing actions of beeswaxed Hanji were even faster than that of Hanji. The optimum dewaxed amounts from beeswaxed Hanji was also obtained in pressure of $40\;kg_f$ under heating conditions.

• 대한한의학방제학회지
• /
• 제15권2호
• /
• pp.171-178
• /
• 2007

This study is clinical report for a acute stroke patient who was improved by treatment of a herbal medication. Stroke patients often shows spirit disorder in early stage. However, the cases which applied Onbyung theory are rare. This paper aims to show that Onbyung theory can be effective to acute stroke. We diagnosed the patient as invasion of the yong system by heat(熱入營分), which showed confusion, insomnia, delirium, anxiety, reddened tongue and dry mouth with cracked lip. After administration of Chungyung-tang(淸營湯) in Wen bing Tiao (溫病條辨), the patient showed those symptoms were highly improved. Thus, we concluded that Onbyung Theory can the patient be adapted to improve the symptom of acute stroke.

• Environmental Engineering Research
• /
• 제22권3호
• /
• pp.266-276
• /
• 2017

A life cycle impact assessment was applied in an industrial waste incineration plant to evaluate the direct and indirect environmental impacts based on toxicity and non-toxicity categories. The detailed life cycle inventory of material and energy inputs and emission outputs was compiled based on the realistic data collected from a local industrial waste incineration plant, and the Korean life cycle inventory and ecoinvent database. The functional unit was the treatment of 1 tonne of industrial waste by incineration and the system boundary included the incineration plant and landfilling of ash. The result on the variation of the impact by the unit processes showed that the direct impact was decreased by 79.3, 71.6, and 90.1% for the processes in a semi dry reactor, bag filter, and wet scrubber, respectively. Considering the final impact produced from stack, the toxicity categories comprised 91.7% of the total impact. Among the toxicity impact categories, the impact in the eco-toxicity category was most significant. A separate estimation of the impact due to direct and indirect emissions showed that the direct impact was 97.7% of the total impact. The steam recovered from the waste heat of the incineration plant resulted in a negative environmental burden.

• 한국주조공학회지
• /
• 제19권1호
• /
• pp.24-32
• /
• 1999

A series of investigations for Austempered Ductile Iron (ADI) castings were carried out by using the specimens with various chemical compositions and heat treatment conditions. The rolling wear characteristics of alloyed austempered ductile irons under an unlubricated dry rolling condition was evaluated by the Amsler type test with 9.09% sliding ratio. Generally, the wear amount was increased with the austempering temperature and decreased when the hardness of the matrix was higher. The alloying elements also influenced the austempering reaction, the microstructure and the mechanical properties. In this study, the mechanical properties (i.e.) ultimate tensile strength (UTS), hardness, elongation) and the wear resistance are analysed to show the relationship between the alloying elements and the austempering temperatures. Mo, Cu and Ni are alloyed individually or in combination. It has been found that when Cu and Ni alloyed individually to a casting, the wear amount is increased than others with elements alloyed in combination. The amount of rolling wear loss was decreased when Mo was alloyed in cast iron, individually or in combination.