• Journal of the Korean Wood Science and Technology
• /
• v.24 no.2
• /
• pp.42-45
• /
• 1996

A residue from the newsprint waste was investigated as a filler in adhesive for bonding southern pine plywood. The residue was prepared by drying the wet residue to 8% moisture content and grinding the dry material using a laboratory Wiley mitt with a 75-${\mu}m$(200-mesh) screen. The residue was compared to a commercial filler commonly used in structural plywood adhesives. A total of 48 three-ply panels. 12.7mm nominal thickness and 0.3 by 0.3 m in size, were fabricated at two press times(4 and 5 min) and three assembly times(20, 40 and 60 min). Evaluations of the residue were carried out by performance tension shear tests after two 4-hour boil accelerated aging tests on plywood. The test results included tension shear strength and estimated wood failure values. All plywood made with the residue filler were comparable to the control-bonded plywood. These results indicate that residue from the newsprint waste streams would be suitable as filler for plywood adhesives.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.41 no.1
• /
• pp.79-85
• /
• 1999

Use of soils with crushed expanded polystyrene(EPS) satisfied both recycling of industrial waste and development of new light-weight fill materials. Objectives of the study were to make the mixed the mixed soils with the crushed EPS and to suggest the most rational mixing ration as a fill material. A series of laboratory tests was performed to investigate the relationship between miximum dry density and optimum moisture contenr and to find the variation of CBR for mixtures with 3 soils and 2 sizes of the crushed EPS. Results of the test showed that the sizes fo the curshed EPS had a little effect on the properties of mixed soils. But gradatiion of soils and mixing ration with the crushed EPS were important factors to characterize compaction properties of the mixed soils.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 1998.10a
• /
• pp.444-448
• /
• 1998

This paper presents the results of an experimental investigation on the compaction and compressive strength of polypropylene fiber reinforced soils. This study has been performed to obtain the physical properties of PFRS(polypropylene fiber reinforced soil) such as strain-stress relationships, OMC(optimum moisture contents) and ${\gamma}$$_{dmax}$ (maximum dry unit weight), with four different concentrations(i.e., 0.1%, 0.3%, 0.5% and 1.0% weights) of mono-filament and fibrillated polypropylene fibers. The test results indicate an appreciable increase in strength due to addition of fibers. OMC is increased with the concentration ratio of fiber, but ${\gamma}$$_{dmax}$ is decreased. From the viewpoint of strength, the fibrillated polypropylene fiber soil is more effective than the mono-filament polypropylene fiber soil.oil.

• Food Science of Animal Resources
• /
• v.40 no.6
• /
• pp.896-907
• /
• 2020

Imaging technique or computer vision (CV) technology has received huge attention as a rapid and non-destructive technique throughout the world for measuring quality attributes of agricultural products including meat and meat products. This study was conducted to test the ability of CV technology to predict the quality attributes of beef. Images were captured from longissimus dorsi muscle in beef at 24 h post-mortem. Traits evaluated were color value (L*, a*, b*), pH, drip loss, cooking loss, dry matter, moisture, crude protein, fat, ash, thiobarbituric acid reactive substance (TBARS), peroxide value (POV), free fatty acid (FFA), total coliform count (TCC), total viable count (TVC) and total yeast-mould count (TYMC). Images were analyzed using the Matlab software (R2015a). Different reference values were determined by physicochemical, proximate, biochemical and microbiological test. All determination were done in triplicate and the mean value was reported. Data analysis was carried out using the programme Statgraphics Centurion XVI. Calibration and validation model were fitted using the software Unscrambler X version 9.7. A higher correlation found in a* (r=0.65) and moisture (r=0.56) with 'a*' value obtained from image analysis and the highest calibration and prediction accuracy was found in lightness (r²_c=0.73, r²_p=0.69) in beef. Results of this work show that CV technology may be a useful tool for predicting meat quality traits in the laboratory and meat processing industries.

• Korean Journal of Agricultural Science
• /
• v.13 no.2
• /
• pp.227-242
• /
• 1986

This paper describes the observed behavior in the direct shear test on decomposed granite soil having the complicate engineering properties at various different levels of factors. The objectives of this study were to investigate the characteristics of the decomposed granite soil under controlled various moisture content, dry density, strain rate and soaking which give influence to the shear strength. The results were summarized as follows; 1. The shear strength was decreased remarkably with the increasing of moisture contents of A and B soil were 5-10% and 15-20% respectively. 2. Cohesion and angle of internal friction were decreased with the increasing of moisture content and increased with the increasing of dry density. 3. The shear strength was increased with the increasing of normal stress and volume change was decreased on the whole. The shear strength was generally increased with the increasing of the strain rate. 4. As dry density increases, A-soil shows the progressive failure and the decrease of volume change while B-soil shows the initial failure and the increase of volume change. 5. The relationships between the soaked and unsoaked specimens were as follows ; ${\tau}_f=0.1009+1.026{{\tau}_f}^*$ (A-soil), ${\tau}_f=0.1586+0.8005{{\tau}_f}^*$ (B-soil) 6. Angle of internal friction of the direct shear test shows larger value than that of the triaxial compression test. All effective stress path was nearly similar.

• International Journal of Highway Engineering
• /
• v.3 no.3 s.9
• /
• pp.135-146
• /
• 2001

This study focused on the investigation of compressive and flexural strengths development, and bond strength of latex modified concrete in order to validate the feasibility of application into concrete bridge deck overlay. Pull-out bond test was used for evaluating the bond strength of latex modified concrete to substrate. The main experimental variables were latex-cement ratio, surface preparation and moisture levels. The compressive strength of latex modified concrete decreased slightly and the flexural strength increased as the latex content increased from 5% to 20%. This might be due to the flexibility latex filled in voids and interconnections of hydrated cement and aggregates by a film of latex particles, respectively. In general, increasing the amount of latex will produce concrete with increased tensile and flexural strength and lower modulus of elasticity. Significant improvements in bond strength between new and existing concrete were achieved through the modification of the new concrete bridge deck overlay by latex polymers. The effect of surface preparation on bond of latex modified concrete to conventional concrete were significant at the conditions by sand paper and wire brush. A better bond could be achieved by rough surface rather than smooth. The saturated condition of surface is the most appropriate moisture level among the considered followed by dry condition and wet condition.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.49-58
• /
• 1998

An experimental study was performed to discover the effect of adsorbed moisture on the rolling resistance behavior of pure silver coated 52100 bearing steel. Plasma surface modifications were performed on the silver coated specimen to change the wetting characteristics. Experiments using a thrust ball beating-typed roiling test-rig were performed under vacuum, dry air and various tmmidity conditions. Results showed that the changes in the wetting characteristics influenced remarkably on the silver particle agglomeration and resulted in the different behavior of rolling resistance with humidity.

• Tribology and Lubricants
• /
• v.15 no.4
• /
• pp.321-327
• /
• 1999

An experimental study was performed to discover the effect of adsorbed moisture on the rolling resistance behavior of pure silver-coated 52100 bearing steel. Plasma surface modifications were performed on the silver-coated specimen to change the wetting characteristics. Experiments using a thrust ball bearing-type rolling test-rig were performed under vacuum, dry air and various humidity conditions. Results showed that the changes in the wetting characteristics influenced remarkably on the silver particle agglomeration and resulted in the different behavior of rolling resistance with humidity.

• Journal of the Korean Society of Safety
• /
• v.5 no.3
• /
• pp.3-7
• /
• 1990

This study is conducted to experiment on the performance test for 20 types of Filter-integrated Half-masks which could not only protect workers exposed to dusty environment, but also improve workability. Results and conclusions are as follows ： 1) Respirators that removal efficiency of aerosols is 95 percent or more are 11 kinds(55%), and those who are 99.9 percent or more are 4 kinds(20%). Respirators that inhalation resistance is 4 mm in water or less are 13 kinds(65%), and those who are 6 mm in water or less are 17 kinds(85%). Respirators that efficiency of cumulative inhalation resistance is 100 percent or less are 11 kinds(55%) . 2) Respirators that resistance of moisture inhalation is 6 mm in water or less are 11 kinds(55%). and those who are 10 mm in water or less are 13 kinds(65cio), Respira'tors that ratio of removal efficiency for aerosols between dry and wet conditions is 95 percent or more are 9 kinds(45%). 3) Respirators which are not only 95 percent or more for removal efficiency of aersosls and 6 mm in water or less for inhalation resistance, but also 200 percent or less for efficiency of cumulative inhalation resistance, are 8 kinds(40％). Respirators which are not only 99.9 percent or more for removal efficiency and 6 mm in water or less for inhalation resistance, but also 100 percent or less for efficiency of cumulative inhalation resistance, are 3 kinds(15%). Respirators which are not only 95 percent or more for removal efficiency of aerosols and 6 mm in water or less for inhalation resistance, but also 200 percent or less for efficiency of cumulative inhalation resistance and 10 mm in water or less for resistance of moisture inhalation, are 6 kinds(30％) . 4) As standard rrlodel of artificial human head which would be perhaps different from the true one Is used to experiment fitness test, leakage rate is shown to be more or less high. However, artificial human head shall be accurately examined and follow-up studt. would be conducted in the future.

• Korean Journal of Plant Resources
• /
• v.14 no.3
• /
• pp.251-258
• /
• 2001

Predehydration effects for cryopreservation in -196$^{\circ}C$ liquid nitrogen were studied in Korean native Aquilegia buergeriana var. oxysepala Kitamura and A. flabellata var. pumila Kudo seeds. Aquilegia species seeds were adjusted to moisture contents between 3.2 and 9.7% by air dry treatments. Seeds were placed in paper envelopes after submerged in liquid nitrogen and rewarming in 38 $^{\circ}C$ water. Seeds moisture contents by duration of drying were identified as controlling factors in the survival of Aquilegia species seeds for cryopreservation. Aquilegia species seeds having approximate 5% moisture content were able to withstand cooling to -l96$^{\circ}C$. Undehydrated seeds of Aquilegia buergeriana var. oxysepala Kitamura after being cryopreservated in liquid nitrogen have a 10.9% of moisture content and show 52.5% in germination. But, Aquilegia buergeriana var. oxysepala Kitamura seeds dehydrated by drying for 60 min. to have 6.0% of moisture content before cryopreservation show 84.7% in germination test. Properly dehydrated seeds after being stored in liquid nitrogen showed over 60% in germination rate and also shows an uniform sprouting time,11~13 days in average. Any morphologically deformity in germinating beds has not been observed. Results from this study suggest that Aquilegia species seeds can cryopreservation in liquid nitrogen if the seed moisture content is controled by a proper amount of dehydration.