• International Journal of Safety
• /
• 제3권1호
• /
• pp.20-26
• /
• 2004

The system considered in this model consists of a single, semi- transparent, diesel fuel droplet, which is immobile in the heating area and surrounded by a quiescent air. A uniform external radiation field surrounds the droplet. Results from mathematical simulation suggest that because of the higher surface temperature, the external radiative heating of the droplet can promote an earlier ignition of the fuel vapour/air mixture. The radiative heating of the droplet increases the mass transfer from the droplet to the surrounding gas-phase, thus, decreasing the heterogeneity of the fuel droplet/air system.

• 한국축산식품학회지
• /
• 제38권6호
• /
• pp.1294-1304
• /
• 2018

The aims of this research were to examine the effect of heating temperature (65, 75, and $85^{\circ}C$) and $CaCl_2$ concentration level (3, 4, and 5 mM) on the physicochemical properties of ${\beta}$-lactoglobulin (${\beta}$-lg) nanoemulsions (NEs) and to study how the droplet size of NEs affects the bioaccessibility (BA) of coenzyme $Q_{10}$ ($CoQ_{10}$). The droplet size of NEs and BA of $CoQ_{10}$ was assessed by particle size analyzer and UV-Vis spectrophotometer, respectively. An increase in heating temperature and $CaCl_2$ concentration level resulted in a significant (p<0.05) increase in the droplet size of NEs while there were no significant differences in polydispersity index and zeta-potential of NEs. When NEs containing $CoQ_{10}$ were incubated in simulated small intestinal phases, an increase in the droplet size and polydispersity index of NEs was observed. This indicated that NEs were not stable in small intestine and digestion of NEs occurred. As heating temperature and $CaCl_2$ concentration level were decreased, a significant (p<0.05) increase in BA of $CoQ_{10}$ was observed. There was a significant (p<0.05) increase in BA of $CoQ_{10}$ with a decrease in the droplet size of NEs. In conclusion, heating temperature and $CaCl_2$ concentration level were key-parameters affecting the initial droplet size of NEs and BA of $CoQ_{10}$ was negatively correlated with initial droplet size of NEs.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.208-211
• /
• 2005

연소기 설계에 유용한 자료를 제공하기 위해 연소실내에서 연료와 산화제의 분무 연소에 관한 수치적 해석을 수행하였다. 분무 모델로 DSF 모델과 Euler-Lagrange 방법을 사용하였다. 액적 가열을 고려하여 액적의 온도 변화를 계산하였다. 액적과 가스상의 커플효과와 가스상과 증발된 기체상의 커플효과를 고려하기 위해 PSIC 모델을 사용하여 계산하였다.

• 대한기계학회논문집B
• /
• 제20권5호
• /
• pp.1700-1716
• /
• 1996

The two-dimensional, unsteady, laminar conservation equations for mass, momentum, energy and species transport in the gas phase and mass, momentum and energy in the liquid phase are solved simultaneously in spherical coordinates in order to study heating and vaporization of a droplet entrained in the oscillating flow. The numerical solution gives the velocity and temperature distribution in both gas and liquid phase as a function of time. When the gas flow oscillates around an vaporizing droplet, the liquid flow circulates in the clockwise or counterclockwise direction and the temperature distribution in the liquid phase changes its shapes, depending on the gas fow direction. When the gas flow changes its direction of circulating liquid flow is opposite to the gas flow, forming two vortex circulating in the opposite direction. During the heating period, the difference in the maximum and minimum temperature is large, followed by the almost uniform temperature slightly below the boiling temperature. The mass and heat transfer from the droplet depend on the droplet temperature, droplet diameter and the magnitude of relative velocity, giving the droplet lifetime different from the d$^{2}$-law.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 Techno-Fair 및 추계학술대회 논문집 전기물성,응용부문
• /
• pp.104-105
• /
• 2007

In this study, characteristics of silver ink-jet printing were investigated under various substrate treatments such as substrate heating, hydrophobic coating, and ultraviolet(UV)/ozone soaking. Fluorocarbon(FC) film was spin-coated on the polyimide (PI) film substrate to obtain a hydrophobic surface. Although hydrophobicity of the FC film could reduce the diameter of the printed droplets, the singlet images printed on the FC film surface showed irregularities in the pattern size and the position of the printed droplet along with droplet merging phenomenon. The proposed UV/ozone soaking of the FC film improved the uniformity of the pattern size and the droplet position after printing and substrate heating was very effective way in preventing droplet merging. By heating of the substrate after UV/ozone soaking of the coated FC film, silver conductive lines of 78-116 ${\mu}m$ line were successfully printed at low substrate temperatures of $40^{\circ}C$.

• 에너지공학
• /
• 제11권1호
• /
• pp.74-80
• /
• 2002

본 연구는 불꽃 점화 기관의 실린더내의 연료 액적의 기화과정에 대한 수치 해석이다. 본 연구의 특징은 무차원 임계 액적 수명시간을 정의하여 가솔린엔진의 흡입 및 압축행정동안 연료 액적의 가열 및 기화과정을 모델화한 것이다. 수치해석 결과는 압축행정동안 기체 온도 및 압력의 동시적 증가는 액적의 기화율에 서로 보상적인 영향을 미치려는 경향을 보이고 있다. 즉 실린더 내 환경의 변화는 연료 액적의 기화과정에 민감하지 않다는 것을 보이고 있다. 이 프로그램은 압축행정 말기에 완전히 기화할 수 있는 액적의 크기를 예측할 수 있다.

• 한국분무공학회지
• /
• 제23권2호
• /
• pp.90-95
• /
• 2018

The goal of this study is to experimentally observe the autoignition phenomena of a diesel/1-butanol mixture droplet in ambient pressure and $700^{\circ}C$ condition. A volume ratio of 1-butanol in the fuel was set to 25, 50 and 75%. A single droplet was installed at the tip of fine thermocouple, and the electric furnace dropped down to make elevated temperature condition. Droplet behavior during the experiment could be divided into 3 stages including droplet heating, puffing and autoignition/combustion. Puffing process intensively observed for the case of 1-butanol volume ratio of 25 and 50%, but did not occur at 75%. Increase of 1-butanol volume ratio hindered rise of the droplet temperature and delayed ignition. In addition, puffing process also affected on autoignition, so the ignition delay of 1-butanol volume ratio of 50% was became longer than that of 75% case.

• 한국연소학회지
• /
• 제4권1호
• /
• pp.17-26
• /
• 1999

Vaporization, ignition and combustion of fuel droplets in tandem array are theoretically investigated to understand the droplet interactions in combustors. Including the effects of density variation in gas-phase, internal circulation and transient liquid heating, a numerical studies are performed by changing parameters such as initial droplet temperatures, initial droplet spacings, initial Reynolds numbers, surrounding gas temperatures, and activation energies of fuel vapors. Combustion regime maps classify the droplet combustion phenomena according to the configuration and location of the flame with respect to injection Reynolds numbers and surrounding gas temperatures. In addition, it is shown that the dynamic histories of droplets and ignition delay times are dependent on droplet size ratios and initial spacings of tandem droplets.

• 대한기계학회논문집B
• /
• 제25권6호
• /
• pp.845-852
• /
• 2001

The characteristics of evaporation cooling of single droplet on a heated surface were studied experimentally. The two kinds of heater modules were tested to measure cooling characteristics of metal surface (high conductivity) and Teflon surface (low-energy surface, low conductivity). The results showed that time averaged heat flux during droplet evaporation increased exponentially with initial surface temperatures of brass, copper and steel. The heat flux and evaporation time did not varied with metal conductivities. However, the temperature drop after the deposition of droplet was larger on Teflon than on the metals. Thus, the correlation of interface temperature between liquid droplet and metal surface was proposed as a function of the initial surface temperature of heating materials, which could be applied to both metal and non-metal ones.

• 대한기계학회논문집
• /
• 제17권7호
• /
• pp.1823-1832
• /
• 1993

CWS(coal-water slurry) is used for application in power plants, boilers, industrial furnaces. A single coal-water slurry droplet ignition has been examined to reveal the basic nature of their evaporation, volatilization and heating processes. The interior droplet temperature distribution has been considered. The effect of coal thermal conductivity, droplet size, water fraction in the slurry, gas temperature and velocity and radiation on the ignition phenomena were also studied. Either increasing the velocity and gas temperature or decreasing the droplet size and water fraction in the slurry may reduce the time for evaporation and ignition delay time.