• 대한환경공학회지
• /
• 제33권4호
• /
• pp.223-230
• /
• 2011

EMEP/EEA Emission Inventory Guidebook에 의하면 자동차 주행에 따른 총 대기오염물질 배출량을 Hot Start와 Cold Start로 구분해 산출하도록 하고 있다. 본 연구에서는 이러한 자동차 주행주기 특성을 감안하여 교통사업의 타당성 분석 시환경비용절감 편익의 현실적인 산정방안에 대해 검토하였다. 이를 위해 교통수요 분석모형(EMME/3)을 이용하여 분석영향권내 모든 링크단위의 교통량과 통행속도 자료를 활용하는 Tier 3 방식으로 환경오염 물질을 선출하였다. 본 연구에서 제안된 방법론의 적용성 검토를 위해 현재 계획중인 철도 투자평가사업에 적용하였으며, 적용결과 환경부문의 편익이 기존 대비 약 30% 정도 증가하는 것으로 나타났다. 향후 본 연구에서 제안한 방법론이 투자평가과정에서 적용된다면 철도와 같은 친환경 교통수단의 투자활성화에 기여할 것으로 기대한다.

• 한국수소및신에너지학회논문집
• /
• 제28권3호
• /
• pp.287-294
• /
• 2017

EVs manufacturers typically target a range of 300 km on a fully charged battery. Many studies have been conducted to improve these disadvantages. As a results, the mileage of EVs is expected to increase significantly. However, as the distance traveled by EVs increases, current test method (SCT) have many difficulties. The biggest problem is that it takes a lot of time to test an EVs and greatly increases the error rate during the test period. In order to solve these problems, this paper discusses the fuel economy test method of EVs for energy efficiency and mileage. The comparison of test methods was achieved by chassis dynamometer test about EVs. These review of test methods are intended to both improve testing efficiency and provide a practical testing methodology that can be easily adapted to accommodate future testing enhancements. In conclusion, the results of MCT mode and SCT mode comparison show similar results within 3 %, confirming that the test method is appropriate. Also, as the CSCM distance becomes shorter in the MCT mode, the mileage becomes longer and the fuel economy becomes lower. As a result, the error from the SCT test results is expected to increase. In order to minimize the error of SCT measurement fuel economy, it is recommended to maximize the CSCM driving distance. However, since the timing of the EOT is not clearly known, it is reasonable to define the allowable range of the CSCE to be within 20 % of the MCT total mileage.

• 한국산학기술학회논문지
• /
• 제15권8호
• /
• pp.4723-4728
• /
• 2014

본 연구에서는 1-D 해석 프로그램인 AMESim을 활용하여 열전소자와 디젤엔진을 모델링하여 이를 New European Driving Cycle (NEDC) 운전모드에서 구동시킨 자동차에서 나오는 폐열을 이용해 열전소자로 발전을 하고 이에 따른 결과를 분석해보는 연구를 수행하였다. 열전소자 모델링 시 배기폐열 회수율 및 전기 에너지 변환률 뿐만 아니라 재료적 특성을 고려하여 열전달부분에 초점을 맞추었다. 또한, 디젤 산화 촉매(DOC)를 설계하여 열전소자로 인한 폐열회수가 디젤 산화촉매 활성화에 미치는 영향과, 그 결과 배기가스의 성분별 증감을 조사하였다. 열전소자를 이용한 폐열회수는 자동차 연비개선에 도움이 되지만, 배기가스의 온도를 떨어뜨려 촉매 활성화에 영향을 미치게 되면, CO와 HC 배출이 최대 14% 증가하는 것을 관찰하였다. 따라서, 열전소자를 이용한 배기 폐열 회수 시스템 개발 시에 배기에 미치는 영향을 고려해야 한다.

• 한국기계가공학회지
• /
• 제18권7호
• /
• pp.56-62
• /
• 2019

The high-precision laser scriber carries out scribing alumina ceramic substrates for manufacturing ultra-small chip resistors. The ceramic substrates are loaded, aligned, scribed, transferred, and unloaded. The entire process is fully automated, thereby minimizing the scribing cycle time of the ceramic substrates and improving the throughput. The scriber consists of the laser optical system, pick-up module of ceramic substrates, pre-alignment module, TH axis drive work table, automation module for substrate loading / unloading, and high-speed scribing control S/W. The loader / unloader unit, which has the greatest influence on the scribing cycle time of the substrates, carries the substrates to the work table that carries out the cutting line work by driving the X and Y axes as well as by adsorbing the ceramic substrates. The loader / unloader unit consists of the magazine up / down part, X-axis drive part for conveying the substrates to the left and right direction, and the vision part for detecting the edge of the substrate for the primary pre-alignment of the substrates. In this paper, the laser scribing machining simulation is performed by applying the instrument mechanism of each component module. Through this study, the scribing machining process is first verified by analyzing the process operation and work area of each module in advance. In addition, the scribing machining process is optimized by comparing and analyzing the scribing cycle time of one ceramic substrate according to the alignment stage module speed.

• 대한기계학회논문집B
• /
• 제41권11호
• /
• pp.775-784
• /
• 2017

본 연구의 목적은 운행자동차에 있어서 안전운행과 환경에 문제가 없는 효과적인 엔진튜닝의 작업가능성을 확인하고, 튜닝엔진의 특징을 파악하여 엔진튜닝 검사의 기초자료를 분석하는 것이다. 비튜닝 및 튜닝 엔진 2-1, 2-2, 2-3의 4종류에 대한 넓은 범위의 엔진회전수 하에서 4행정, 4기통 DOHC, 터보 인터쿨러, 수냉 가솔린엔진의 실제 운행자동차를 사용하여 공연비 및 성능 특성에 미치는 튜닝엔진의 효과를 실험적으로 조사했다. 운행 가솔린자동차에 대한 엔진의 튜닝 부분은 흡기 다기관, 흡기 파이프, 공기필터, 배기 다기관, 배기 파이프 및 소음기를 포함한다. 1인이 탑승한 5단 자동변속기를 갖는 운행 가솔린자동차 비튜닝 및 튜닝 엔진의 공연비 및 토크는 차대 동력계(Dynojet 224xLC)에 의하여 실험에 의해 측정하였다. 운행 가솔린자동차 튜닝엔진의 최대 토크는 비튜닝엔진보다 평균 103.68% 만큼 증가되었고, 튜닝엔진의 최대 출력은 비튜닝엔진보다도 평균 119.68% 만큼 증가되었음을 알았다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.3180-3186
• /
• 2011

A segmented scissors type switch has been developed for the urban transit maglev demonstration line to be commercialized near Incheon International Airport in 2013. Based on the design of the previous segmented 3-way switch, the scissors switch is composed of four segmented 2-way switches up/down and left/right and a turn table in the mid point. The main function of the scissors switch is to change the running direction of the train at end terminals. The developed scissors switch is planned to be installed in front of the 102 station, which has a side platform, of the demonstration line. The total length of the switch is 65m and the distance between the up and down track centerlines is 6m. The 2-way switches and turn table are made of steel box type beams, and have their own driving unit, locking unit, control unit, levitation and propulsion rails, and so on. Installed in the factory, a 100,000-cycle continuous operation test was carried out after manual and automatic test operations. The applicapability of the developed switch was verified through the measurements of the linearity of the track after repetitive operations, the mechanical operation noise, the load of the main driving motor, the safety of the control panel, the natural frequency of the girder, the deformation of the girder, and so on.

• Journal of Power Electronics
• /
• 제11권2호
• /
• pp.237-243
• /
• 2011

Lithium batteries are widely used in mobile electronic devices due to their higher voltage and energy density, lighter weight and longer life cycle when compared to other secondary batteries. In particular, a high demand for lithium batteries is expected for electric cars. In the case of the lithium batteries used in electric cars, driving distance must be calculated accurately and discharging should not be done below a level that makes it impossible to crank. Therefore, accurate information on the state-of-charge (SOC) becomes an essential element for reliable driving. In this paper, a novel method for estimating the SOC of lithium polymer batteries using AC impedance is proposed. In the proposed method, the parameters are extracted by fitting the measured impedance spectrum on an equivalent impedance model and the variation in the parameter values at each SOC is used to estimate the SOC. Also to shorten the long length of time required for the measurement of the impedance spectrum, a novel method is proposed that can extract the equivalent impedance model parameters of lithium polymer batteries with the impedance measured at only two specific frequencies. Experiments are conducted on lithium polymer batteries, with similar capacities, made by different manufacturers to prove the validity of the proposed method.

• Journal of Electrical Engineering and Technology
• /
• 제8권6호
• /
• pp.1431-1438
• /
• 2013

A pack-level battery hardware-in-the-loop simulation (B-HILS) platform is implemented. It consists of dynamic vehicle models using PSAT and multiple control interfaces including real-time 3D driving and GPS mode. In real-time 3D driving mode, user can drive a virtual vehicle using actual drive equipment such as steering wheel and accelerator to generate the cycle profile of the battery. In GPS mode, actual road traffic and terrain effects can be simulated using GPS data while the trajectory is displayed on Google map. In the latter part of the paper, several performance tests of an actual lithium-polymer battery pack are carried out utilizing the developed system. All experiments are conducted as parts of actual development process of a commercial battery pack adopting 2nd generation Prius as a target vehicle model. Through the experiments, the low temperature performance and fuel efficiency of the battery are quantitatively investigated in comparison with the original nickel-metal hydride (NiMH) pack of the Prius.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권4호
• /
• pp.399-403
• /
• 2013

지하자원 채굴을 위한 갱도나 협소하고 위험한 공간에서 사람을 대신하여 채굴작업을 수행하는 로봇의 수요가 증가되고 있다. 본 연구에서는 원격 제어형 로봇 및 작업기구를 개발하여 석탄광산에서 원활한 채굴작업을 수행가능한지를 시험 갱도에서 확인하였다. 시험한 결과 개발된 로봇은 주행속도 1.0 km/h, 등판가능 경사도 $10^{\circ}$ 정도임을 확인하였다. 협소한 공간에서 분쇄기의 타격회수 500bpm, 타격력 $30kg_f-m$을 유지해야만 터널에서의 채굴작업이 가능하고, 최대 3시간까지 작업을 수행하기 위해서는 터널 내부의 환경조건을 분석하여 로봇을 충분히 냉각시키는 냉각시스템이 필요함을 알 수 있었다.

• 한국생산제조학회지
• /
• 제24권5호
• /
• pp.541-547
• /
• 2015

In this study, the performance of a low-floor midsize bus under development is predicted through simulations. To predict the vehicle's acceleration, maximum speed, and uphill driving performance, a forward simulator which calculates the vehicle power is developed. Also we verify the forward simulator by comparing simulations and test result for benchmarking vehicle. To predict the fuel consumption, we use a backward simulator for a specified road cycle. However, to predict the fuel consumption using the backward simulation the engine fuel-consumption map is needed. The engine fuel-consumption map extracting data from a similar sized diesel engine is used by re-scaling the maximum torque. As a result, we simulate the vehicle's forward performance with a new engine. Further, we simulated the backward performance to optimize the fuel efficiency and gearshift timing.