• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.2
• /
• pp.135-142
• /
• 2015

The Anti-Rolling Tank(ART) has an advantage over the other roll stabilizing devices, when ship is staying and working at one site of sea. An important design point of ART is the tank tuning, that is, matching the tank natural period to the ship's roll natural period. Since the load condition and consequently the roll natural period of ship is to be changed widely, the natural period of ART also has to be changed widely. In case of the existing U-tube type ART with a single layer duct, the tank natural period can be changed in a relatively narrow range. This paper suggests a new U-tube type ART system using a double layer duct to enable wide change of ART natural period. Through the roll experiments performed in regular beam waves for a box-type model ship, it is shown that the double layer duct ART has about two times wider period range and a better reducing effect of roll magnitude than the single layer duct ART.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.9
• /
• pp.1493-1496
• /
• 2016

This paper proposes a system for reducing the standby power consumption in using the consumer electronic devices such as a television, a home theater, a set-top box, or a DVD player. The system is consisted of a flyback converter, monitoring circuits, a relay and a micro-processor. The proposed system can reduce the standby power consumption by disconnecting the AC input and the consumer devices can be turned on with a remote control. The proposed standby power system consumes the low power to receive the infrared signal from the remote controller. Furthermore, a electronic double layer capacitor is used to store the energy with high efficiency. The proposed power system can operate the 플라이백 converter to charge the electronic double layer capacitor and connect the AC input to the consumer electronic devices. The proposed power circuit can reduce the standby power consumption in AV devices without increasing the cost. The prototype is implemented to verify the system with the commercialized products.

• Solar Energy
• /
• v.6 no.2
• /
• pp.15-21
• /
• 1986

In this study, an experimental double diffusive thermohaline system heated from below was constructed and the phenomena of each layer developed in the system were observed. The experiment was performed with the initial salt concentration gradient of $-436.2kg/m^4$ and the net heat flux of approximately $176w/m^2$. An electroconductivity-temperature probe was made and used for the measurements of salt concentration. As the result of this study, it was found that the salt concentration decreased in the bottom mixed layer and increased in the top mixed layer during the experiment while the salt concentration gradient in the diffusive layer unchanged. It was also found that the interfacial boundary layers were due largely to variations in salt concentration rather than temperature.

• Advances in materials Research
• /
• v.12 no.3
• /
• pp.193-210
• /
• 2023

This paper aims to analyze the dynamic response of a double nanobeam system with a medium viscoelastic layer under a moving load. The governing equations are based on the Eringen nonlocal theory. A thin viscoelastic layer has coupled two nanobeams together. An exact solution is derived for each nanobeam, and the dynamic deflection is achieved. The effect of parameters such as nonlocal parameter, velocity of moving load, spring coefficient and the viscoelastic layer damping ratio was studied. The results showed that the effect of the nonlocal parameter is significantly important and the classical theories are not suitable for nano and microstructures.

• Journal of Internet of Things and Convergence
• /
• v.9 no.3
• /
• pp.61-67
• /
• 2023

In order to optimize the pulse electroforming copper process, a double hidden layer BP (Back Propagation) neural network is constructed. Through sample training, the mapping relationship between electroforming copper process conditions and target properties is accurately established, and the prediction of microhardness and tensile strength of the electroforming layer in the pulse electroforming copper process is realized. The predicted results are verified by electrodeposition copper test in copper pyrophosphate solution system with pulse power supply. The results show that the microhardness and tensile strength of copper layer predicted by "3-4-3-2" structure double hidden layer neural network are very close to the experimental values, and the relative error is less than 2.32%. In the parameter range, the microhardness of copper layer is between 100.3~205.6MPa and the tensile strength is between 112~485MPa.When the microhardness and tensile strength are optimal,the corresponding process conditions are as follows: current density is 2A-dm-2, pulse frequency is 2KHz and pulse duty cycle is 10%.

• Earthquakes and Structures
• /
• v.9 no.4
• /
• pp.767-788
• /
• 2015

A steel shear wall with double-tapered links and in-plane reference was developed for assisting the assessment of the structural condition of a building after an earthquake while maintaining the original role of the wall as a passive damper device. The double-tapered link subjected to in-plane shear deformation is designed to deform torsionally after the onset of local buckling and works as an indicator of the maximum shear deformation sustained by the shear wall during an earthquake. This paper first examines the effectiveness of double-tapered links in the assessment of the structural condition under various types of loading. A design procedure using a baseline incremental two-cycle loading protocol is verified numerically and experimentally. Meanwhile, in-plane reference links are introduced to double-tapered links and greatly enhance objectivity in the inspection of notable torsional deformation with the naked eye. Finally, a double-layer system, which consists of a layer with double-tapered links and a layer with rectangular links made of low-yield-point steel, is tested to demonstrate the feasibility of realizing both structural condition assessment and enhanced energy dissipation.

• Fashion & Textile Research Journal
• /
• v.11 no.2
• /
• pp.359-362
• /
• 2009

This study investigates the behavior of water vapor permeability of a layered system to find out a comfortable combination of a layered system for outdoor activities and examines the water vapor permeability of various types of outdoor clothing fabrics. The layered system includes the base layer such as sportswool and polyester/cotton fabrics, the middle layer such as single and double sided fleece fabrics, and the shell layer such as polyurethane-coated, PTFE-laminated and microfiber fabrics in this experiment. Results show that the layered system was applied, it was working together as a whole having some influence on each other layer, though every layer offered varying degree of water vapor permeability. Water vapor permeability of layered system exactly followed the same trend as the shell layer, which is all vapor permeable water repellent fabrics as a single layer. The rate of water vapor transfer through a layered system is mainly related to the type of vapor permeable water repellent fabrics used for the shell layer.

• Structural Engineering and Mechanics
• /
• v.8 no.4
• /
• pp.383-399
• /
• 1999

In some space truss applications, particularly those with large spans, the choice of a triple-layer system might prove more cast effective than the more commonly used double-layer solution. However, there are currently no clear guidelines as to which system would be more competitive for intermediate span lengths. In this paper, comparisons in terms of the weight, stiffness and number of joints and members are made between the two system types and presented in order to simplify the choice process for the designer. The comparisons are carried out using an approximate analysis technique that is explained in this paper, and checked to be reasonably accurate and suitable for the preliminary design of space trusses.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.15 no.4
• /
• pp.380-387
• /
• 1986

In this study, the models for a double-diffusive thermohaline system heated from below were developed and the governing equations were established taking account of the density variation with time. The six order Runge-Kutta method was used for the solution of the simultaneous governing differential equations and the temperature and salt concentration distributions and height of each layer within the system were predicted. As the result of this study, it was found that the predicted values with the convective layer growing proportionality constant of 0.18 showed a good agreement with available experimental data. It was also found that the effect of density change with time on the temperature profile in the bottom convective layer could not be negligible.

• Korean Journal of Optics and Photonics
• /
• v.18 no.6
• /
• pp.421-425
• /
• 2007

A new 3D rear projection display system using double-layer polarization-selective screen systems, one stacked in front of the other, has been developed. The front and rear screens are made of scattering polarizer films, and they either diffuse-scatter or transmit the incident light depending on the polarization state of the light. The near and for images are projected onto the front and rear screens, respectively, using light waves with mutually orthogonal polarization states. The new display system produces clear high-resolution images, which are visible over a wide range of viewing angle. It was found that the impression of depth is pronounced and eyestrain is only comparable to that by 2D display systems.