• 한국작물학회지
• /
• 제36권1호
• /
• pp.70-73
• /
• 1991

벼의 기공 분포 밀도에 미치는 규소의 영향을 구명코자 동계 온냉조절온실에서 규소 농도를 달리하여 수경재배한 벼 제 7 엽기의 엽신 부위별 기공수 및 기공세포 크기를 관찰한 결과 규소 농도 증가로 밀양2003 엽신중 기공수가 줄어들고 엽의 전 표면적에 대한 기공수$\times$기공세포 크기로 나타낸 기공세포의 분포 밀도가 낮게 되어 양면 표피의 cuticle-silica 2중층의 존재 이외에도 수분경제면에서 유리한 특성을 갖게 될 것으로 간주되었다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2001년도 춘계종합학술대회
• /
• pp.418-422
• /
• 2001

This paper presents a developed squired cage induction motor for axial flow fan. The developed squirrel cage induction noter for axial flow fan is exchanged the position, rotor and stater. In this method a fan blade is attached to outside rotor. So we can protect the motor from rain and reduce noise, and there is no need to have bending duct to locate the fan motor. Carried out experimental test with this induction motor, and the results were as follows. Starting torque was 21kgㆍcm@120V, maximum efficiency was 0.84@120V. The characteristics of tests were the same as double squirrel-cage type IM.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 춘계 학술논문 발표대회
• /
• pp.279-280
• /
• 2018

The waterproofing material can be roughly divided into a coating material and a sheet waterproofing material. In the case of coating waterproofing materials, sheet waterproofing materials, which are easy to use in terms of workability and quality control, have been recently used because of their incomplete use of coating thickness, long curing time and poor blending due to in situ blending. However, in the case of the sheet waterproofing material, since the sheet overlapping portion is inevitably generated, various defects (breakage due to the behavior) are frequently observed. Therefore, it is imperative to establish fundamental measures to minimize this.

• 한국안전학회지
• /
• 제10권2호
• /
• pp.39-45
• /
• 1995

Three-dimensional flow measurements were conducted between the rotors of the CRP To understand mean flow phenomena of the CRP's, the results of the three-dimensional measurements were shown. Interaction noise of the CRP, which increases the overall ,level of sound pressure In the new propulsion system, is documented by using the double conditional sampling technique. The rear rotor will increase the axial flow between the rotors of a CRP depending upon the relative locations between the forward and the rear rotor blades. The decay and spreading of the forward wakes and the upstream propagation of the rear blade disturbances are shown along with the interaction of the flow disturbances by the two rotors of blades.

• 대한기계학회논문집B
• /
• 제23권6호
• /
• pp.761-768
• /
• 1999

This paper is studied to find the optimum condition of double-inlet Sirocco fan installed in an indoor PAC for low noise operation by the Taguchi method. The goal of this study is to obtain the best combination of each control factor which results in a desired flowrate of Sirocco fan with minimum variability. In this study, the parameter design of the Taguchi method is adopted for robust design by the dynamic characteristic analysis using orthogonal arrays and S/N ratios. The flowrate measurements are conducted by using a multiple-nozzle-type fan tester according to the orthogonal array L9($3^4$). The results of this study can be summarized as follows ; (i) The optimum condition of control factor is a set of where A is an inner to outer diameter ratio($D_1/D_2$), B is a width to outer diameter ratio($L/D_2$), C is a blade attachment angle(${\theta}$) and D is a number of blade(Z), (ii) The flowrate under the optimum condition satisfies the equation $y=0.0384{\cdot}M$ where M is a signal factor, namely number of revolution. The flowrate performance improves about 7.3% more largely as compared with the current condition, which results in about 35RPM reduction of number of revolution for the target flowrate $18.5m^3/min$, and (iii) The sensitivity analysis shows that the major factors in contribution to flowrate performance are A, B, and D ; the percentage contributions of each control factor are 44.01%(Z), 26.77%($D_1/D_2$) and 20.42%($L/D_2$).

• 태양에너지
• /
• 제10권1호
• /
• pp.47-56
• /
• 1990

수직축 다리우스 풍력 터어빈의 공기역학적 특성을 해석코자 날개요소이론과 운동량 이론에 근거하는 이중다류관모델을 정립하여 모델풍동실험과 병행하여 비교분석하였다. 이중 다류관 모델은 아직 수정 보완의 여지는 있으나 터어빈을 통과하는 유동의 변화가 심하지 않은 날개끝속도비나 회전면적비가 작은 경우에는 비교적 정확히 터어빈의 공기역학적 특성을 예측함을 알 수 있었고, 모형풍동실험을 통해 정확한 터어빈 회전수제어로서 각 특성변수들에 대한 영향을 살피었다. 본 연구의 결과로서는 다리우스 터어빈의 설계 및 운전특성 예측에의 응용이 기대될 수 있다.

• Journal of Mechanical Science and Technology
• /
• 제15권12호
• /
• pp.1860-1868
• /
• 2001

An experimental investigation was carried out to clarify unsteady flow fields with rotating stall cell, especially behavior of stall cell, in a high specific-speed diagonal flow fan. As its specific-speed is vary high for a diagonal flow fan, its pressure-flow rate curve tends to indicate unstable characteristics caused by rotating stall similar to axial flow fan. Although for an axial flow fan many researchers have investigated such the flow field, for a diagonal flow fan tittle study has been done. In this study, velocity fields at rotor Inlet in a high specific-speed diagonal flow fan were measured by use of a single slant hot-wire probe. These data were processed by using the "Double Phase-Locked Averaging"(DPLA) technique, i. e. phases of both the rotor blade and the stall cell were taken into account. The behaviors of stall cell at rotor inlet were visualized for the meridional, tangential and radial velocity.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.136-142
• /
• 2008

The influence of different grids on numerical prediction of subsonic compressor performance and stall was investigated. Two types of grids were examined, structured H type grid and structured O-H type grid. Evaluations were conducted by comparing the numerical results with experimental results obtained from a low-speed single-stage rig test for a new concept compressor, called diffuser passage compressor, aiming at improving tip clearance sensitivity. At low mass flow operating conditions, the numerical calculation with O-H type grid showed that the lowest mass flow operating point for which the calculation was able to converge was almost the same as the lowest steady mass flow obtained from the rig test. On the other hand, the numerical calculation with structured H type grid diverged at higher mass flow operating point. It was found that this difference was attributed to the effect of double-valuedness of H type grid that existed at leading edge on the boundary layer development on the blade surface.

• International Journal of Fluid Machinery and Systems
• /
• 제4권3호
• /
• pp.334-340
• /
• 2011

Turbo-pumps have weak points, such as the pumping operation is unstable on the positive slope of the head curve and/or the cavitation occurs at the low suction head. To improve simultaneously both weak points, the first author invented the unique pumping unit composed of the tandem impellers and the peculiar motor with the double rotational armatures. The front and the rear impellers are driven by the inner and the outer armatures of the motor, respectively. Both impeller speeds are automatically and smartly adjusted in response to the pumping discharge, while the rotational torques between both impellers/armatures are counter-balanced. Such speeds contribute to suppress successfully not only the unstable operation at the low discharge but also the cavitation at the high discharge, as verified with the axial flow type pumping unit in the previous paper. Continuously, this paper investigates experimentally the effects of the tandem impeller profiles on the pump performances and the rotational speeds against the discharge, using the impellers whose loads are low and/or high at the normal discharge. The worthy remarks are that (a) the unstable operation is suppressed as expected and the shut off power is scarcely large in the smart control, (b) the blade profile contributes to determine the discharge giving the maximum/minimum rotational speed where the reverse flow may incipiently appears at the front impeller inlet, (c) the tandem impeller profiles scarcely affect the rotational speeds, while the loads of the front and the rear impellers are same, but (d) the impeller with the low load must run faster and the impeller with the high load must run slower at the same discharge to take the same rotational torque, and (e) the reverse flow at the inlet and the swirling velocity component at the outlet of the front impeller with the high load require making the rotational speed of the rear impeller with low load fairly faster at the lower discharge.

• 한국식품과학회지
• /
• 제18권5호
• /
• pp.351-356
• /
• 1986

단(單)원통형 및 원통형 드럼건조기를 이용하여 잘게 저민 생선으로부터 플레이크를 성공적으로 만들 수 있었다. 생선의 높은 지방함량으로 인해 저민 생선이 드럼에 잘 들러붙지 않는 문제점은 타피오카가루의 형태로 2.5%의 전분을 저민 생선에 첨가함으로서 건조양상에는 영향을 미치지 않으면서 해결될 수 있었다. 제품의 수분함량을 일정한 수준으로 유지할 경우 건고형분(乾固形分)의 생산속도는 드럼간의 간격을 최소로 줄였을때 최고에 도달하였다. 건고형분(乾固形分)의 생산속도는 드럼의 회전속도가 증가할수록 선형적으로 증가하였고 제품의 품질이 손상되지 않는 범위에서 스팀의 압력이 높을수록 증가하였다. 총괄 열전달계수는 드럼의 회전수가 증가함에 따라 증가한 반면에 드럼간의 간격이 커짐에 따라 증가하지는 않았다. $MR\;=\;A\;\exp(\;-k{\theta})$로 표시되는 가장 보편적인 건조 모델식이 드럼건조에도 적용될 수 있었다.