• Korean Journal of Clinical Pharmacy
• /
• v.18 no.1
• /
• pp.1-5
• /
• 2008

The goal of this research was to find out the effect of dispensing error prevention program on the incidence of the error in a university hospital pharmacy in Daegu. Dispensing error in this research was defined as the error identified during double-checking process, so it does not mean that the wrong dispensing was administered to patient. Drug name error was the most frequently found error, accounting for about one third of all dispensing errors, and was followed by counting error, strength error, dosage form error, and others. Similar drug name was identified as the most frequent reason for the error, taking up about two thirds of all drug name errors. In this research, six months of dispensing error prevention program resulted in statistically significant reduction of dispensing error by 42 percent. Therefore, it is recommended that hospital pharmacy implement such prevention program regularly to reduce the incidence of the error. Finally, it appears that drug approval authority should closely check the similar drug names and have power to command pharmaceutical company to change the name if pertinent.

• Journal of Korean Society of Water and Wastewater
• /
• v.25 no.1
• /
• pp.15-21
• /
• 2011

Arsenic is one of the most abundant contaminant found in waste mine tailings, because of it's carcinogenic property, the countries like United states of America and Europe have made stringent regulations which govern the concentration of arsenic in drinking water. The current study focuses on different treatment methods for removal of arsenic from waste water. Treatment method the high strength arsenic waste water is treated with Fe(III)-ettringite by co-precipitation method. Number of experiments were carried out to decide the optimal dosage of Fe(III)-ettringite to treat arsenic waste water. The Fe(III)-ettringite was synthesized by taking appropriate equivalent ratios of calcium oxide and ferric chloride in proportion to the arsenic. The best removal efficiencies of 94% were observed at a As/(Ca: Fe) ratio of 1:3. The maximum removal of arsenic was observed in pH range of 12. But as the pH increases the arsenic removal efficiency decreases as portlandite is formed in the pH above 12. The analysis of surface of precipitate conform the needle like structure of ettringite. This treatment technique has promising features such as, the chemicals required in the treatment as well as the sludge generated can be reduced. The operating pH range is in alkaline region which is advantageous over traditional treatment process which has lower pH. Also the co-precipitation not only helps in removal of arsenic but also heavy metals.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.29 no.3
• /
• pp.34-42
• /
• 1997

This study was carried out to investigate the proper cooking conditions of soda-anthraquinone and alkaline sulfite-anthraquinone pulping of rice-straw, and get basic data f9r the use of rice-straw chemical pulp through the test of characteristics and physical properties of pulps made in the various cooking conditions From the experimental results , we can conclude as follows. In the soda-anthraquinone pulping of rice-straw, the optimum cooking conditions were 60 min. at $150^{\circ}C$ in the amount of caustic soda of 20% with the addition of anthraquinone(0.05%). And total yield, Kappa No. and brightness of pulp made in the condition above mentioned were 41.9%, 7.7 and 51.1 respectively. In the alkaline sulfite-anthraquinone pulping of rice-straw, the proper mixing ratio of cooking chemical(caustic soda : sodium sulfite) was 50:50. And the optimum cooking conditions were 60 min. at $150^{\circ}C$ in the amount of cooking chemical of 20% with the addition of anthraquinone(0.05%). At that time, the total yield, Kappa No, and brightness of pulp were 50.1%, 9.1 and 40.2 respectively. As a result, the alkaline sulfite-anthraquinone pulping was superior to the soda-anthraquinone pulping in the aspect of yield, but inferior in the viewpoints of Kappa No. and brightness. For the comparison of qualities of pulps made in the various cooking methods and conditions, the physical properties of four sorts of pulps were tested. As a result, soda-anthraquinone pulps were superior to alkaline sulfite-anthraquinone pulps in the various strengths excluding tear strength and brightness. On the other hand, pulps made in the condition of addition of cooking chemical of 20% were superior to pulps in the dosage of 15% in the aspects of all the strengths and brightness.

• The Journal of Korean Obstetrics and Gynecology
• /
• v.35 no.4
• /
• pp.161-173
• /
• 2022

Objectives: This study was conducted to evaluate the effectiveness of acupuncture in patients with primary menstrual difficulties taking NSAIDs. Methods: 30 women with primary menstrual difficulties with NSAIDs were assigned to treatment groups (n=15) and control groups (n=15). On their first visit, both groups were provided with a menstrual diary and were required to record the intensity of pain and the dosage of painkillers during each menstrual cycle. The treatment group received two acupuncture treatments per cycle during two cycles, and the control group did not receive acupuncture. Pain strength during menstruation was evaluated using Visual Analogue Scale (VAS), and the total number of painkillers taken during menstruation and the average number of painkillers taken during a single dose was measured. Results: The treatment group had significant pain relief compared to the pre-test group and significant differences from the control group. In addition, there was a significant difference between the treatment group and the control group in the frequency of taking painkillers during the menstrual period and the dose in the test group was significantly lower than before treatment. Conclusions: This clinical trial showed that this acupuncture can help alleviate primary menstruation and reduce the use of nonsteroidal anti-inflammatory drugs.

• Journal of Ginseng Research
• /
• v.48 no.3
• /
• pp.323-332
• /
• 2024

Background: Studies have reported that the combination of two or more therapeutic compounds at certain ratios has more noticeable pharmaceutical properties than single compounds and requires reduced dosage of each agent. Red ginseng and velvet antler have been extensively used in boosting immunity and physical strength and preventing diseases. Thus, this study was conducted to elucidate the skin-protective potentials of red ginseng extract (RGE) and velvet antler extract (VAE) alone or in combination on ultraviolet (UVB)-irradiated human keratinocytes and SKH-1 hairless mice. Methods: HaCaT cells were preincubated with RGE/VAE alone or in combination for 2 h before UVB (30 mJ/cm²) irradiation. SKH-1 mice were orally given RGE/VAE alone or in combination for 15 days before exposure to single dose of UVB (600 mJ/cm²). Treated cells and treated skin tissues were collected and subjected to subsequent experiments. Results: RGE/VAE pretreatment alone or in combination significantly prevented UVB-induced cell death, apoptosis, reactive oxygen species production, and DNA damage in keratinocytes and SKH-1 mouse skins by downregulating mitogen-activated protein kinases/activator protein 1/nuclear factor kappa B and caspase signaling pathways. These extracts also strengthened the antioxidant defense systems and skin barriers in UVB-irradiated HaCaT cells and SKH-1 mouse skins. Furthermore, RGE/VAE co-administration appeared to be more effective in preventing UVB-caused skin injury than these extracts used alone. Conclusion: Overall, these findings suggest that the consumption of RGE/VAE, especially in combination, offers a protective ability against UVB-caused skin injury by preventing inflammation and apoptosis and enhancing antioxidant capacity.

• Korean Journal of Agricultural Science
• /
• v.16 no.2
• /
• pp.212-224
• /
• 1989

This paper reports results of an investigation to determine properties of superplasticizered fly ash concrete. The mixture proportions of fly ash were 0, 10, 20 and 30%, by weight of cement, and superplasticizer was added as a percentage of fly ash, 0, 0.6, 12 and 1.8%. To investigate the effective use of the superplasticized fly ash concrete, the basic data were analyzed. The results obtained were summarized as follows : 1. The unit water content was decreased by 1%, 6% and increased by 2% to the ratio of addition of fly ash 10%, 20%, 30%, respectively, but in case of the superplasticized fly ash concrete, it was decreased by 3~16%, 4~14% and 10~17%, at 0.6, 12, and 1.8% dosage of superplasticizer, respectively. 2. In the properties of the fresh fly ash concrete, the slump loss was reduced with the ratio of replacement of fly ash increased, and with times went by. When using superplasticizer in fly ash substituting concrete, the fludity in the concrete was not decreased. 3. The compressive strength of fly ash concrete at early ages was lower than that of ordinary concrete. At the later age of 28 days, the compressive strength with 20% addition of fly ash was increased than that of ordinary concrete. In cased of 10%, 30% addition of fly ash, the compressive strength were reduced. From this, it was proved that the optimum amount of fly ash appears to be about 20%. The compressive strength at all ages of superplasticized fly ash concrete was significantly higher than that of fly ash concrete, with increasing fly ash content. 4. In case of the tensile strength, the effects of the increasing strength with the ages were similar to those of the compressive strtength, and at the later ages was seen a decreasing tendency of strengths. 5. The correlation between compressive and tensile strength of superplasticized fly ash concrete was highly significant. The multiple regression equations of compressive and tensile strength were obtained on a function of the mixture proportion of fly ash and the addition of superplasticizer. The relation between compressive and tensile strength is higher than for ordinary concrete. The strength ratio is 7~11, and it is higher than that of ordinary concrete, 8~10. 6. Bulk density was decreased by 1~3% compared with ordinary concrete with the mixture proportion of fly ash increased, 10~30%, and decreased by 1~2% with the superplasticizer added 0.6~1.8%.

• Economic and Environmental Geology
• /
• v.46 no.6
• /
• pp.535-544
• /
• 2013

Influence of sulfate on the early hydration in the solidification treatment of abandoned mine tailings was characterized. Solidified specimens using hydrated lime as a binder were prepared with various amounts of added $Na_2SO_4$ and different curing days. Unconfined compressive strength measurement, heavy metal leaching test, XRD analysis were performed after 7-, 14- and 28-days curing. According to curing days strength of solidified specimens using only distilled water increased but those with addition of $Na_2SO_4$ decreased. External cracks of specimens developed definitely with increasing $Na_2SO_4$ concentration and curing days. Concentrations of Cu, Cd, Zn, and As in the leached solutions from solidified specimens decreased significantly but Pb was leached readily in cases of hydrated lime dosage more than 10 wt%. Gypsum and $MgSO_4$ were identified in the cracked solidified specimens by XRD analysis, and pillar-shaped crystals of SEM image were identified as gypsum in reference with EDS analysis. Crystallization of sulfate in the process of lime-tailing solidification caused cracking, which should be supplemented for solidification treatment of highly sulfur-contained tailing.

• Journal of the Korea Concrete Institute
• /
• v.18 no.1 s.91
• /
• pp.21-28
• /
• 2006

This paper presents both experimental and analytical studies for the development of an ECC(Engineered Cementitious Composites) using ground granulated blast furnace slag(slag). This material has been focused on achieving moderately high composite strength while maintaining high ductility, represented by strain-hardening behavior in uniaxial tension. In the material development, micromechanics was adopted to properly select optimized range of the composition based on steady-state cracking theory and experimental studies on matrix, and interfacial properties. A single fiber pullout test and a wedge splitting test were employed to measure the bond properties of the fiber in a matrix and the fracture toughness of mortar matrix. The addition of the slag resulted in slight increases in the frictional bond strength and the fracture toughness. Subsequent direct tensile tests demonstrate that the fiber reinforced mortar exhibited high ductile uniaxial tension behavior with a maximum strain capacity of 3.6%. Both ductility and tensile strength(~5.3 MPa) of the composite produced with slag were measured to be significantly higher than those of the composite without slag. The slag particles contribute to improving matrix strength and fiber dispersion, which is incorporated with enhanced workability attributed to the oxidized grain surface. This result suggests that, within the limited slag dosage employed in the present study, the contribution of slag particles to the workability overwhelms the side-effect of decreased potential of saturated multiple cracking.

• Journal of the Korea Concrete Institute
• /
• v.25 no.3
• /
• pp.339-345
• /
• 2013

This study is to derive from the required performances and the optimum mix proportion of the roof concrete placed in the in-ground LNG storage tank with a capacity of 200000 $m^3$, and propose the actual data for site concrete work. The concrete placing work without sliding and segregation in the fresh concrete condition is very important because the slope of domed roof is varied in the large range by its curvature. Also the control of hydration heat and the strength development at test ages are classified with massive section about 1.4 m thick and considered to the pre-stressing work and removal of air support after concrete placing work. Considering above condition, slump range is selected $100{\pm}25$ mm under the slope $20^{\circ}$ and $150{\pm}25$ mm over the slope $20^{\circ}$ s until 60 minutes of elapsed time. Also, the roof concrete is satisfied with compressive strength range including design strength at 91 days (30 MPa), pre-stressing work at 7 days (10 MPa), air support removal work at 21 days (14 MPa). Replacement ratio of limestone powder is determined by confined water ratio test and main design factors include water-cement ratio (W/C), sand-aggregate ratio and dosage of admixture. As test results, the optimum mix proportion of the roof concrete used low heat cement is as followings. 1) Replacement ratio of limestone powder 25% by confined water ratio test 2) Water-cement ratio 57.8% 3) Sand-aggregate ratio 42.0%. Also, test results for the adiabatic temperature rising test is satisfied with its criteria and shown the lower value compared to preceding storage tank (TK-13, 14). These required performances and the optimum mix proportion is to apply the actual construction work.

• Journal of the Korea Concrete Institute
• /
• v.16 no.2 s.80
• /
• pp.241-248
• /
• 2004

The rheological properties of cement paste system mixed with mineral admixtures (MAs) used to increase the strength and improve durability and fluidity of concrete were investigated. And cement paste systems were designed as one-, two- and three-ingredients blended paste systems. The rheological properties of paste systems were assessed by Rotovisco RT 20 rheometer (Hakke inc.) having a cylindrical serrated spindle. The rheological properties of one-ingredient paste systems were improved with increasing the dosage of superplasticizer. For two-ingredients paste systems, as increasing the replacement ratio of blast furnace slag (BFS) and fly ash (FA), the yield stress and plastic viscosity were decreased compared with non-replacement. In the ordinary portland cement (OPC)-silica fume (SF) paste systems, in accordance with an increase in the replacement ratio of SF, the yield stress and plastic viscosity were increased steeply. For three-ingredients paste systems, both OPC-BFS-SF and OPC-FA-SF paste systems, the rheological properties were improved compared with the only replacement of SF. In the case of both two-and three-ingredients paste systems, the rheological properties using BFS were improved more than FA.