• 수산해양기술연구
• /
• 제50권3호
• /
• pp.284-291
• /
• 2014

Finely-striate buccinum Buccinum striatissimum, a species of whelks, is caught mainly by pot in the eastern coastal waters of Korea. In order to determine the size selectivity of pot for the species, comparative fishing experiments were conducted near Yeongil Bay from June to September in 2003 using the dome-shaped pots with different five mesh sizes (17.1, 24.8, 35.3, 39.8, and 48.3 mm). The parameters of logistic equation were estimated by the SELECT (Share Each Length's Catch Total) method based on a multinomial distribution. The model with the estimated split parameter was found to fit the catch data best. The master selection curve was estimated to be s (R)=exp (13.044R-16.438)/[1 + exp (13.044R-16.438)], where R is the ratio of shell height to mesh size. The relative shell height of 50% retention was 1.260, and the selection range was 0.168. Enlargement in mesh size of the pot allows more small-sized whelks to escape.

• 한국소음진동공학회논문집
• /
• 제16권7호
• /
• pp.729-738
• /
• 2006

Knowledge of acoustic transmission loss of acoustic window material has a great importance for the sonar performance in ship. The purpose of this study was to investigate the measurement and analysis method for the acoustic transmission loss of the acoustic window materials for sonar dome. The measurement and analysis were carried out in water with GRP material. Transmission losses were calculated based on integrated direct and transmitted signals. The experimental setup enabled to vary the angle of incidence. Thus the transmission loss data could be expressed as the function of frequency and angle of rotation. In this paper, diffraction effect of incident angle, size of specimen with test material, transmission analysis method and multiple waves as incident acoustic signal were discussed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.1183-1189
• /
• 2006

Knowledge of acoustic transmission loss of acoustic window material has a great Importance for the sonar performance in ship. The purpose of This study was to investigate the measurement and analysis method for me acoustic transmission loss of the acoustic window materials for sonar dome. The measurement and analysis were carried out in water with GRP material. Transmission losses were calculated based on integrated direct and transmitted signals. The experimental setup enabled to vary the angle of incidence. Thus the transmission loss data could be expressed as the function of frequency and angle of rotation. In this paper, diffraction effect of incident angle, size of specimen with test material, transmission analysis method and multiple waves as incident acoustic signal wet-e discussed

• Journal of Welding and Joining
• /
• 제31권6호
• /
• pp.27-31
• /
• 2013

Magnesium alloy is used on parts of aircraft and electronic equipment because of the highest specific strength among the common metal materials. Recently, studies about appling magnesium alloy sheet to automotive bodies are on the increase rapidly. For application to automotive bodies, researches about characteristics of resistance spot welding of magnesium alloy sheet are essential. Magnesium alloy has low boiling point, so getting sound bead shape is difficult when appling varies welding processes. Resistance spot welding is also particular about setting optimum welding conditions because of spatter generation, pores and cracks occurrence in nugget. And life of electrodes is very short because of alloying with copper that main material of electrodes. This requires frequent dressing and replacement of electrodes and decrease in productivity of resistance spot welding on magnesium alloy. Therefore in this study, for effective analysis of changes in tensile shear load and nugget size during electrode life test, evaluate detail characteristics of resistance spot welding on magnesium alloy sheet using dome type electrode.

• Journal of Korean Neurosurgical Society
• /
• 제60권5호
• /
• pp.504-510
• /
• 2017

Objective : To investigate the morphological and hemodynamic parameters associated with middle cerebral artery (MCA) bifurcation aneurysm rupture. Methods : A retrospective study of 67 consecutive patients was carried out based on 3D digital subtraction angiography data. Morphological and hemodynamic parameters including aneurysm size parameters (dome width, height, and perpendicular height), longest dimension from the aneurysm neck to the dome tip, neck width, aneurysm area, aspect ratio, Longest dimension from the aneurysm neck to the dome tip (Dmax) to dome width, and height-width, Bottleneck factor, as well as wall shear stress (WSS), low WSS area (LSA), percentage of LSA (LSA%) and energy loss (EL) were estimated. Parameters between ruptured and un-ruptured groups were analyzed. Receiver operating characteristics were generated to check prediction performance of all significant variables. Results : Sixty-seven patients with MCA bifurcation aneurysm were included (31 unruptured, 36 ruptured). Dmax (p=0.008) was greater in ruptured group than that in un-ruptured group. D/W (p<0.001) and the percentage of the low WSS area ($0.09{\pm}0.13$ vs. $0.01{\pm}0.03$, p<0.001) were also greater in the ruptured group. Moreover, the EL in ruptured group was higher than that in unruptured group ($6.39{\pm}5.04$ vs. $1.53{\pm}0.86$, p<0.001). Multivariate regression analysis suggested D/W and EL were significant predictors of rupture of MCA bifurcation aneurysms. Correlation analyses revealed the D/W value was positively associated with the EL (R=0.442, p<0.01). Conclusion : D/W and EL might be the most two favorable factors to predict rupture risk of MCA bifurcation aneurysms.

• 한국추진공학회지
• /
• 제23권4호
• /
• pp.21-27
• /
• 2019

연소가스에 의한 내압 조건에서 필라멘트 와인딩 공법으로 제작되는 복합재 연소관은 돔에서 구조적으로 취약해진다. 본 논문에서는 압력분포비(PDR) 변화에 따른 복합재 돔의 파열압력을 비교하기 위해 유한 요소 해석을 수행하였다. 돔 내/외면 응력, 금속 보스 체적을 산출함으로써, 정량적으로 복합재 연소관의 성능을 비교하였다. 그 결과, PDR 2.5-3.0에서 파손 모드의 임계점이 존재함을 확인하였다. PDR 2.5-3.5 설계는 연소관 파열압력의 변동 없이 금속 보스 무게 감량이 가능하며, 돔 형상 및 오프닝 크기에 대해 설계 기준값이 변경되므로 해석 및 시험을 통한 규명이 필요하다.

• 수산해양기술연구
• /
• 제49권4호
• /
• pp.368-376
• /
• 2013

Fishing experiments were carried out in the adjacent sea of Yeongil Bay, the eastern cost of Korea from 2003 to 2004 using the dome-shaped pots with different five mesh sizes (17.1, 24.8, 35.3, 39.8, and 48.3mm) in order to determine the size selectivity of pots for the whelk, Buccinum opisthoplectum. The catch species were composed of Buccinum opisthoplectum (45.4%), Buccinum striatissimum (30.1%), Pandalopsis japonica (9.3%), Chionoecetes opilio (8.9%), and so on. The shell height (l) of Buccinum opisthoplectum caught in the experimental fishing pots was measured. The SELECT (Share Each Length's Catch Total) analysis method was applied with fishing data to obtain master selection curve. The model with the estimated split parameter was found to fit the catch data best. The master selection curve was estimated to be s (R)〓exp (7.833R-10.871)/[1 + exp (7.833R-10.871], where R is the ratio of shell height to mesh size. The relative shell length for 50% retention was 1.388, and the selection range was 0.281. It means that the pots of larger mesh size allow more whelks of small size to escape.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 1997년도 제15회 KOSCO SYMPOSIUM 논문집
• /
• pp.135-151
• /
• 1997

The preliminary design and performance test for determining dimensions of gas turbine combustor were investigated. The combustor design program was developed and applied to design our combustor. and detailed design for determining of swirler. dome and liner holes were performed experimentally. The swirler. which govern the combustion characteristics of combustor, was determined $40^{\circ}$ as swirl angle at first performance test. After second performance test the swirler was re-determined by 24 mm i.d.. 34 mm o.d., and swirl angle of $45^{\circ}$. The geometry of liner holes were determined by considering the flame stability and recirculation zone size. It was found that flame can be more easily stabilized by adjusting the swirier dimensions rather than liner holes. The geometry of swirler and liner holes were re-determined by final performance test with dilution holes. Also. the performance of combustor was evaluated by analysis of exhaust gases.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2003년도 가을 학술발표회 논문집
• /
• pp.340-347
• /
• 2003

The aim of regularization of a structural configuration is to obtain a structure that consists of elements with identical or nearly identical length. And it is also possible to modify the configuration in a manner that the size of the elements vary in accordance with a specified pattern. For practical purpose, geodesic dome is cut off at a suitable place in order to make it fit on horizontal. Inevitably this pattern effects a change of element lengths. The purpose of this study is to verify a method for regularization of structural configuration by genetic algorithms and modify the element lengths of the dome. As a result of regularization of domes with various rise-span ratio, modified configurations have more regular element lengths and are more economical than initial configurations.

• 대한기계학회논문집A
• /
• 제37권1호
• /
• pp.31-37
• /
• 2013

본 연구의 목적은 최적화 해석 기법을 이용하여 복합재 압력용기의 스커트 치수를 도출하는 것이다. 복합재 압력용기 스커트 최적화 해석은 부분문제 근사법을 사용하였으며, APDL(ANSYS Parametric Design Language)을 이용하여 해석의 모든 과정을 일괄처리하였다. 설계변수로는 압력용기 스커트 부위의 두께와 길이를 선정하였으며, 내압에 의해 발생하는 변위와 무게를 각각 목적함수로 하여 최적화 해석을 통해 최적의 스커트 치수를 도출하였다. 그 결과 복합재 압력용기의 스커트 무게를 최대 4.38% 절감할 수 있었다.