• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.12
• /
• pp.1549-1556
• /
• 2004

We have deigned, fabricated and compared four different types of static chaos microfluid mixers, including the mixers using straight channel flow, microblock-induced alternating whirl flow, microchannel-induced lamination flow, and combined alternating whirl-lamination flow. Among them, the alternating whirl-lamination (AWL-type) mixer, composed of 3-D rotationally arranged microblocks and dividing microchannels fabricated by conventional planar lithography process, is effective to reduce the mixing length over wide flow rate ranges. We characterize the performance of the fabricated mixers, through the flow visualization technique using phenolphthalein solution. We verify that the AWL-type microfluid mixer shows the shortest fluid mixing length of 2.8mm∼5.8mm for the flow rate range of Re=0.26∼26 with the pressure drop lower than 5kPa. Compared to the previous mixers, requiring the mixing lengths of 7∼17mm, the AWL-type microfluid mixer results in the 60% reduction of the mixing lengths. Due to the reduced mixing lengths within reasonable pressure drop ranges, the present micromixers have potentials for use in the miniaturized Micro-Total-Analysis-Systems($\mu$TAS).

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.5 s.236
• /
• pp.545-553
• /
• 2005

In the present study, The characteristics of developing steady laminar flows of a straight duct connected to a $180^{\circ}$ curved duct were examined In the entrance region through experimental measurement. Flow characteristics such as shear stress distributions, pressure distributions and friction coefficient experimentally in a square cross-sectional straight duct by using the PIV system. For the PIV measurement by particles produced from mosquito coils particles. The experimental data were obtained at 9 points dividing the test sections by 400mm. Experimental results can be summarized as follows. Critical Reynolds number, $Re_{cr}$ which indicates transition from laminar steady flow to transition steady flow was 2,150. Shear stress per unit length on the wall was stronger than that in the fully developed flow region. This was attributed to the fact that shear stress and pressure loss in the curvature of a duct were increased. Pressure distributions were gradually decreased irrespective of Reynolds number In the whole test section. This trends were in a good agreement with the reference results. Pipe friction coefficient in the steady state flow region was calculate from method of least squares. The co-relationship between fiction coefficient and Reynolds number was established as follow; ${\lambda}=56/Re$.

• Journal of Korean Neurosurgical Society
• /
• v.67 no.2
• /
• pp.158-165
• /
• 2024

Objective : Superficial temporal artery (STA)-middle cerebral artery (MCA) anastomosis is conducted for flow augmentation. In this study, we measured the STA cut flow of a Korean population and evaluated the relationship between STA cut flow and long-term patency of the bypass. Methods : A retrospective study was conducted. Intraoperative measurement of STA flow was conducted using a microvascular flow meter on patients who underwent STA-MCA. After cutting the distal end, the STA flow rate was measured with no resistance and recorded. After finishing anastomosis, STA flow was measured and recorded. The cut flow index was calculated by dividing post anastomosis flow by cut flow in intracranial atherosclerotic stenosis patients. Results : The median STA cut flow was 35.0 mL/min and the post anastomosis flow was 24.0 mL/min. The cut flow of STA decreased with aging (p=0.027) and increased with diameter (p=0.004). The cut flow showed no correlation with history of hypertension or diabetes mellitus (p=0.713 and p=0.786), but did correlate a positively with history of hyperlipidemia (p=0.004). There were no statistical differences in cut flow, STA diameter, and post anastomosis flow between the frontal and parietal branches (p=0.081, p=0.853, and p=0.990, respectively). Conclusion : The median STA cut flow of a Korean population was 35 mL/min. Upon reviewing previous articles, it appears that there are differences in the STA cut flow between Western and Asian patients.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.9
• /
• pp.1058-1065
• /
• 2004

In the present study, characteristics of steady state laminar flows of a straight duct connected to a 180$^{\circ}$ curved duct were examined in the entrance region through experimental and numerical analyses. For the analysis, the governing equations of laminar flows in the Cartesian coordinate system were applied. Flow characteristics such as velocity profiles, and secondary flows were investigated numerically and experimentally in a square cross-sectional straight duct by the PIV system and a CFD code(STAR CD). For the PIV measurement, working fluid produced from mosquito coils smoke. The experimental data were obtained at 9 points dividing the test sections by 400 mm. Experimental and numerical results can be summarized as follows. Critical Reynolds number, Recr which indicates transition from laminar steady flow to transition steady flow was 2,150. As Reynolds number, Re, was increased, dimensionless velocity profiles at the outer wall were increased due to the effect of the centrifugal force and the secondary flows. The intensity of a secondary flow became stronger at the inner wall rather than the outer wall regardless of Reynolds number.

• Korean Journal of Environmental Agriculture
• /
• v.24 no.1
• /
• pp.6-11
• /
• 2005

A prototype surface flow constructed wetland was built in the upstream area of reclaimed tidal lands to improve the water quality of Lake Sihwa by treating severely polluted stream water. In this study, a tracer test using rhodamine-WT was performed to investigate the flow characteristics and to quantify the observed hydraulic residence time (HRT) for a high-lying cell in the Banwol wetland of the Sihwa constructed wetland. The tracer test indicated that even if flow was mainly observed in the open water area of the Banwol wetland, water flowed continuously in the vegetative area and there was no dead zone. The calculated HRT (51.3 hrs), calculated by dividing the wetland volume by the wetland inflow, exceeded the observed HRT (38.7 hrs), since the short-circuiting of flux resulting from irregular topography and vegetation was not reflected in the calculated HRT. The exit tracer concentration curves were reproduced well by both the plug flow with dispersion and tanks-in-series models, indicating that the performance of the Banwol wetland can be estimated accurately using these models.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.281-286
• /
• 2004

The vacuum cleaner motor runs on very high speed for the suction power. Specially, the motive power is provided by the impeller being rotate on very high speed. And centrifugal fan consists of the impeller, the diffuser, and the circular casing. Due to the high rotating speed or the impeller and small gap distance between the impeller and diffuser, the centrifugal fan makes very high noise level at BPF and harmonic frequencies. In order to calculate the sound pressure of centrifugal fan, the unsteady flow data is needed. And Noise cause is dividing to fluid noise by exhaust flow of fan and vibration noise by rotational vibration of vacuum cleaner fan motor. Until now, measuring method has been used to measure vibration by the accelerometer; this method has been not measured for the vibration in some parts of brush and commutator because of motor construction and 3-D vibrating mode. This paper was purposed on the accurate analysis, using laser vibration analyzer,. By using this measured data of noise cause against the difficult part in old times, we would like to use for the design of silent fan motor.

• Journal of the Korea Furniture Society
• /
• v.26 no.2
• /
• pp.112-121
• /
• 2015

Concept based Design-Art is a flow formed while focusing on works not dividing boundaries with concept on top in a transition to content-centered communication methods from medium-centered communication methods so far dividing design genres. This movement begins in a try to create upper-level concepts before works and products come into being in pure art and design respectively. This thesis draws out the definition of Concept based Design-Art through its researches, diagnoses directionality of Concept based Design-Art by analyzing Concept based Design-Artists' works and considers their social duties and roles. Outcome of this study will help working authors, designers, and Design-Artists grasp the changing phases of design and art, establish their own directionality, and predict how the Concept based Design-Art market will change in the years ahead. Besides, it will be a good reference by which for them to build their own 'concept,' consider their relationship to the society and check where they are.

• 한국전산유체공학회:학술대회논문집
• /
• 2000.05a
• /
• pp.127-139
• /
• 2000

Transient aerodynamic response of an airfoil to a rapidly deploying spoiler is numerically investigated using a two-dimensional turbulent compressible Navier-Stokes flow model. The spoiler moving relative to a stationary airfoil is treated by an overset grid bounded by a 'dynamic domain-dividing line' the concept of which is developed first..in this paper. The fluid-dynamic mechanism of the adverse lift due to the rapidly deploying spoiler is analyzed. Also the effect of spoiler deploying rate on the initial behavior of the aerodynamic response is expounded, which is of interest in view of active control technology and controller design for the spoiler. The results of present computation about the stationary as well as moving spoilers are relatively in good agreement with the existing experimental data.

• 한국방재학회:학술대회논문집
• /
• 2010.02a
• /
• pp.96.2-96.2
• /
• 2010

본류부에서 지류부로 유입되는 흐름의 내측 벽면에는 토사나 오염물의 퇴적물침전이 발생하게 된다. 이는 개수로 분류흐름의 특성으로 인하여 이차류 흐름이 나타나는 분리구역이 발생하기 때문이다. 수치모의를 실행하여 Hsu 등(2002)과 Ramamurthy 등 (2007)의 분류흐름 수로의 결과값과 수치모의를 통한 결과를 비교하여 신뢰성이 높음을 알 수 있었다. 본 연구에서는, 분류흐름에서 발생하는 분리구역을 줄이기 위해 분류가 시작되는 본류의 수로의 크기 조절을 통하여 분리구역의 크기를 줄였다. 또한 변형으론 인한 분리구역을 줄이기 위해 본류와 지류가 만나는 모서리 지점을 곡선과 대각선으로 연결하여 유수흐름을 완만하게 만든 지형들을 제안하였다.

• Journal of Distribution Research
• /
• v.8 no.1
• /
• pp.69-89
• /
• 2003

This study aims to find out the relationship between purchase intention of fashion products and affecting factors. Measurement was not on the general Web environment but on the individual websites. It was modeled that the likeness of shopping malls affects purchase intention. Flow, which Csikszentmihalyi(1990) introduced as the state of optimal experience, was to affect purchase intention through the likeness of shopping malls. In addition, characteristics of fashion products were to affect purchase intention. A structural equation modeling was used for estimation. The result shows that the likeness of shopping malls affect purchase intention more than characteristics of fashion products. The difference from other studies is that the sign of Skills on Flow is negative. The effect of Flow on purchase intention is the largest and the next is the characteristics of the shopping malls. These results imply that internet shopping malls have to increase the likeness of shopping malls in addition to interests of the products. In addition, fashion consciousness was tested as a moderator by dividing the subjects into two groups of high and low fashion consciousness. The result shows that fashion consciousness works as a moderator for the variables affecting purchase intention.