• 환경영향평가
• /
• 제14권1호
• /
• pp.17-24
• /
• 2005

This study was performed to evaluate the adsorption rate of phosphate corrosion inhibitor and reaction rate constant in drinking water distribution systems. The optimum concentration of corrosion inhibitor would vary depending on the quality of water, pipe materials, and condition of metal surfaces. The current adsorption study indicated that the residual phosphate concentration of the corrosion inhibitor decreased with the time as it adsorbed on the surface of pipe material. As time went by, the residual phosphate concentration became constant. It means that the formation of the corrosion protection film on metal surfaces is completed.

• 대한기계학회논문집A
• /
• 제27권6호
• /
• pp.923-929
• /
• 2003

In this paper, an analysis of fatigue crack growth behavior from a statistical point of view has been carried out. Fatigue crack growth tests were conducted on sixteen pre-cracked compact tension (CT) specimens of the pressure vessel (SPV50) steel in controlled identical load and environmental conditions. The assessment of the statistical distribution of fatigue crack growth experimental data obtained from SPV50 steel was studied and also the correlation of the parameter C and m in the Paris-Erdogan law was discussed. The probability distribution function of fatigue crack growth life seems to follow the 3-parameter Weibull. The fatigue crack growth rate seems to follow the 3-parameter Weibull and the log-normal distribution. The coefficient of variation (COV) of fatigue crack growth life was observed to decrease as the crack grows. Fatigue crack growth rate data shows a normal distribution for both m and logC. A strong negative linear correlation exists between the coefficient C and the exponent m.

• 동력기계공학회지
• /
• 제17권4호
• /
• pp.86-93
• /
• 2013

This paper deals with the effects of driving force and material properties on statistical distribution of fatigue crack growth rate (FCGR) for the friction stir welded joints of Al 7075-T651 aluminum plate. In this work, the statistical probability distribution of fatigue crack growth rate was analyzed by using our previous constant stress intensity factor range controlled fatigue crack growth test data. As far as this study are concerned, the statistical probability distribution of fatigue crack growth rate for the friction stir welded (FSWed) joints was found to evaluate the variability of fatigue crack growth rate for base metal (BM), heat affected zone (HAZ) and weld metal (WM) specimens. The probability distribution of fatigue crack growth rate for FSWed joints was found to follow well log-normal distribution. The shape parameter of BM and HAZ was decreased with increasing the driving force, however, the shape parameter of WM was decreased and increased with increasing the driving force. The scale parameter of BM, HAZ and WM was increased with the driving force.

• 멤브레인
• /
• 제12권1호
• /
• pp.21-27
• /
• 2002

본 연구에서는 회분여과방식을 이용하여 부하율에 따라 생성되는 생물대사성분의 특성 및 분포를 관찰하였다. 실험에 사용된 기질은 단일 탄소인 phenol을 사용하였으며, 분자량 분포실험을 위하여 분자량이 각각 30K, 100K Dalton 및 $0.45{\mu}$ membrane filter를 이용하여 구하였다. 페놀농도가 120, 230 및 440 mg/L 일 때 비기질이용율(q)은 각각 0.639, 1.281, 1.744 (mgTOC/mg MLSS/day)로 나타났으며 Run C일 때 가장 높은 이용율을 나타냈다 . 내생단계에서 미생물의 사멸율($K_d$)는 각각 0.0536, 0.0661, 0.0749($day^1$)이며 생성계수 ($SMP_e$) 는 각각 0.006, 0.0058, 0.0057($day^1$)로 나타났다. 초기 유입된 기질이 기질분해에 의해 생성된 $SMP_s$로 분해되어지며, 시간경과에 따라 $SMP_{nd}$ 로 진행됨을 알수 있었다. 기질분해 완료 후 미생물의 내생단계에 접어들면서 $SMP_e$성분으로 전환되었다. 유입부하율에 따른 분자량 분포 측정결과는 운전시간이 경고함에 따라 점차 저분자 물질이 고분자의 난분해성 물질로 전환되었다.

• International Journal of Reliability and Applications
• /
• 제10권1호
• /
• pp.43-57
• /
• 2009

In this article, we study the reliability equivalence factor of a series system. The failure rates of the system components are functions of time t. we study two cases of non-constat failure rates (i) weibull distribution (ii) linear increasing failure rate distribution. There are two methods are used to improve the given system. Two types of reliability equivalence factors are discussed. Numerical examples are presented to interpret how one can utilize the obtained results.

• 한국해양공학회지
• /
• 제11권3호
• /
• pp.76-88
• /
• 1997

Constant .DELTA.K fatigue crack growth rate experiments were performed by applying an intermediate single and multiple overload for structural steel, SM45C. The purpose of the present study is to investigate the influence of multiple overloads at various stress intensity factor ranges and the effect of statistical variability of crack retardation behavior. The normalized delayed load cycle, delayed crack length and the minimum crack growth rate are increased with increasing baseline stress intensity factor range when the overload ratio and the number of overload application were constant. The crack retardation under low baseline stress intensity factor range increases by increasing the number of overload application, but the minimum crack growth rate decreases by increasing the number of overload application. A strong linear correlation exists between the minimum crack growth rate and the number of overload applications. And, it was observed that the variability in the crack growth retardation behavior are presented, the probability distribution functions of delayed load cycle, delayed crack length and crack growth life are 2-parameter Weibull. The coefficient of variation of delayed load cycle and delayed crack length for the number of 10 overload applications data are 14.8 and 9.2%, respectively.

• 한국항공우주학회지
• /
• 제35권8호
• /
• pp.706-713
• /
• 2007

코안다 효과를 유발시키기 위해 환상 슬릿과 팽창률이 일정하지 않은 축소 노즐로부터 분사되는 제트의 구조와 환상의 슬릿과 팽창률이 일정한 노즐로부터 분사되는 제트의 구조를 비교 연구하였다. 실험에 있어서 노즐 입구와 출구 직경을 각각 40mm, 20mm로 하였고, 노즐 출구 평균 속도를 90m/s로 하였다. 3축 이송 장치와 스캐닝 밸브 시스템을 이용하여 제트 축 및 반경 방향 압력을 측정하고, 측정된 정압 및 전압으로부터 구한 속도 분포를 비교 검토하였다. 안정성과 수속성이 우수한 제트를 얻기 위해서는 팽창률이 일정하지 않은 노즐보다 팽창률이 일정한 축소 노즐과 환상의 슬릿을 통해 코안다 효과를 이용하여 분사하는 것이 효과적임을 밝혔다. 또한 팽창에 따른 압력 강하도 팽창률이 일정한 노즐의 경우가 상대적으로 더 작게 됨을 알았다.

• 한국자동차공학회논문집
• /
• 제10권4호
• /
• pp.69-76
• /
• 2002

The aim of this study is to provide fundamental informations that make it possible to use a cool stream and a hot stream simultaneously. We changed the pressure of compressed air that flows into a tube, the inner diameter of orifice that a cold stream exits, and the mass flow rate ratio. And in each case, we measured the temperature of a cold stream and a hot stream in each exit of a tube. Also we measured the axial and the radial temperature distribution in internal spare of a tube. From the study, fellowing conclusive remarks 7an be made. First, As the number of nozzles increase, separation point move into the hot exit. Second, When we use guide vane type nozzle, the axial temperature distribution constant over the 0.75 of air mass flow rate radio. Third, When we use Spiral type nozzle, axial and radial temperature distribution in the inner space is higher than another nozzle. Fourth, Axial and radial temperature distribution in the inner space vortex-tube is determined by separation point. And separation point is moved by changing of air mass flow rate ratio. At last, A heating apparatus is possible far vortex-tube to use.

• 한국안전학회지
• /
• 제9권4호
• /
• pp.17-28
• /
• 1994

Chip breaking is important in lathe work for maintaining good surface of the products and safety of operator. The purpose of this study is to investigate the performance of chip breaking and chip shape resulted from the carbide inserts with grooved type and obstruction type chip breaker. Experiments have been performed under the following cutting conditions, (1) constant cutting speed with variable depth of cut and feed rate, (2) constant depth of cut with variable cutting speed and feed rate. Also, the flying distance of chip and it's distribution have been investigated. As a results, good performance of chip breaking can be obtained for small radius of curvature and land width of grooved type chip breaker. And the thickness of chip increase with the increase of feed rate and decrease of cutting speed, and the chip breaking becomes easier with the increase of chip thickness due to the large deformation rate. Obstraction type chip breaker shows better performance of surface roughness than the grooved type. The flying distance of the chips over 90% are less than 1 meter, and the distance decreases as the feed rate decreases.

• 한국자동차공학회논문집
• /
• 제12권3호
• /
• pp.10-18
• /
• 2004

It is well known that the stratified charge combustion has many kind of advantages to combustion characteristics, such as higher thermal efficiency and less CO, NOx levels than conventional homogeneous mixture combustion. Although this combustion can be caused low fuel consumption, it is produced the high unburned hydrocarbon and soot levels because of different equivalence ratio in the combustion chamber. Moreover it has a lot of possibility of low output and misfire if the mixture gas would not be in existence around the spark plug. In this paper, fundamental studies for stratified combustion were carried out using a constant volume combustion chamber. The effect of locally mixture gas distribution according to control the direct injection and premixed injection in the chamber were examined experimentally. In addition, the effects of turbulence on stratified charge combustion process were observed by schlieren photography.