• Geomechanics and Engineering
• /
• 제31권5호
• /
• pp.519-527
• /
• 2022

Shear failure in soil is the primary cause of most geotechnical structure failures or instability. Soil water content is a significant factor affecting soil shear strength. In this study, the shear strength of samples with different water contents was tested. The shear strength, cohesion, and internal friction angle decreased with increasing water content. Based on the variation of cohesion and internal friction angle, the water content zone was divided into a high-water content zone and low-water content zone with a threshold water content of 15.05%. Cohesion and internal friction angle have a good linear relationship with water content in both zones. Environmental Scanning Electron Microscopy (ESEM) test presented that the aggregates size of the compacted loess gradually increases with increasing water content. Meanwhile, the clay in the compacted loess forms a matric that envelops around the surface of the aggregates and fills the inter-aggregates pores. A quantitative analysis of bound water and free water under different water contents using a nuclear magnetic resonance (NMR) test was carried out. The threshold water content between bound water and free water was slightly below the plastic limit, which is consistent with the results of shear strength parameters. Combined with the T2 distributions obtained by NMR, one can define a T2 relaxation time of 1.58 ms as the boundary point for bound water distribution without free water. Finally, the effects of bound water and free water on shear strength parameters were analyzed using linear regression analysis.

• Journal of Korean Ophthalmic Optics Society
• /
• 제10권3호
• /
• pp.159-164
• /
• 2005

Accommodation and convergence is combination movement which is closely connected with each other. When one of them is stimulated, both of functions occur at the same time. Specially, the convergence by the accommodation's stimulation is called as accommodative convergence. That has excess or deficiency according to refraction state of eye. This study was performed by using both of Gradient method and Heterophoria method to 41 adults who have no any ophthalmic disease. 1. As the result of investigation about the distribution of heterophoria at distance, there were orthophoria of 5 subjects, exophoria of 32 and esophoria of 4. Exoporia occupied at the hightest rate. The distribution of heterophoria at near cover a wider range more than at distance. 2. When we measured the horizontal heterophoria amount in the state of relaxation of accommodation power of lens, exophoria amount increased in case of 38 subjects. 3. The person who has $4{\sim}6{\Delta}/D$ which conform to normal AC/A ratio occupied 27 subjects(66%) in Heterophoria method and 16(39%) in Gradient method, respectively.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• 제17권4호
• /
• pp.413-421
• /
• 2004

In this paper, a structural analysis for the pressurized water reactor(PWR) spent nuclear fuel disposal canister which is deposited under the 500m deep underground is carried out to predict the creep deformation of the canister while the underground water and swelling bentonite pressure are applied on the canister. Usually the creep deformation may be caused due to the Pressure and the high heat applied to the canister even though additional external loads are not applied to the canister. These creep deformations depend on the time. In this paper, oかy the underground water and bentonite swelling Pressure are considered for the creep deformation analysis of the canister, because the heat distribution inside canister due the spent fuel is not simple and depends on time. A proper creep function is adopted for the creep analysis. The creep analysis is carried out during $10^8$ seconds. The creep analysis results show that the creep strains are very small and these strains occur usually in the lid and bottom of the canister not in the cast iron insert. A much smaller strain is found in the cast iron insert. Hence, the creep deformation doesn't affect the structural safety of the canister, and also the creep stress which shows the stress relaxation phenomenon doesn't affect the structural safety of the canister.

• Journal of Photoscience
• /
• 제5권3호
• /
• pp.105-109
• /
• 1998

By using the liquid -phase-deposition (LPD) process, which has a potetnial of preparing organic inorganic composite materials, samples doped with benzo[f]quinoline (BfQ)into silica thia films wre prepared. We observed the fluorescene and fluorescene excitation spectra of the samples, as well as the fluorescence lifetimes and time-resoluved fluorescence spectra. The comparison of thefluorescence spectra in pH-controlled buffer solutions yields the results that the dominant species of BfQ in the LPD silica films is a protonated one. The fluorescence band assigned to a hydrogen-bonded species was observed on the samples prepared from the dipping solutions of 3 and 2 M hexafluorosilicic acid. The band assignment was confirmed by the fluorescence lifetime measurement. The FT-IR M hexaflurosilicic acid. The band assignment was confirmed by the flurescence lifetime meausurement. The FT-IR data proved the existence of included water in silica films prepared from the LPD process. The appearance of the band corresponding to the hydrogen-bonded species within LPD silica phases was explained by the proesence of included water. Depending on the preparation conditions of LPD silica films, the band assigned to protonated species shows bad shifts in a wavenumber region between the peak of hydrogen-bonded and typical protonated species. This implies that there is some distribution of steric conformation of protonated species of BfQ interacting with adsorbing sites of LPD silica. The time -resolved fluorescence spectra suggest that some relaxation process is involved in the conformation of BfQ doped into the solid phase of LPD silica.

• Proceedings of KOSOMES biannual meeting
• /
• 해양환경안전학회 2005년도 추계학술대회지
• /
• pp.153-158
• /
• 2005

The turbulent shear flaw around a surface-mounted vertical wall was investigated using the two-frame PIV(CACTUS 3.1) system. From this study, it is revealed that at least 500 instantaneous velocity field data are required for ensemble average to get reliable turbulence statistics, but only 200 field data are sufficient for the time-averaged mean velocity information The flow has an unsteady recirculation region post vertical wall with bottom gap, followed by a slow relaxation to the fiat-plate boundary layer flow. The time-averaged reattachment length estimated from the streamline distribution is about x/H=3H. The large eddy structure in the separated shear layer seems to have signification influence on the development of the separated shear layer and the reattachment process.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.155.2-155.2
• /
• 2013

Strain-relaxed SiGe layer on Si substrate has numerous potential applications for electronic and opto- electronic devices. SiGe layer must have a high degree of strain relaxation and a low dislocation density. Conventionally, strain-relaxed SiGe on Si has been manufactured using compositionally graded buffers, in which very thick SiGe buffers of several micrometers are grown on a Si substrate with Ge composition increasing from the Si substrate to the surface. In this study, a new plasma process, i.e., the combination of PIII&D and HiPIMS, was adopted to implant Ge ions into Si wafer for direct formation of SiGe layer on Si substrate. Due to the high peak power density applied the Ge sputtering target during HiPIMS operation, a large fraction of sputtered Ge atoms is ionized. If the negative high voltage pulse applied to the sample stage in PIII&D system is synchronized with the pulsed Ge plasma, the ion implantation of Ge ions can be successfully accomplished. The PIII&D system for Ge ion implantation on Si (100) substrate was equipped with 3'-magnetron sputtering guns with Ge and Si target, which were operated with a HiPIMS pulsed-DC power supply. The sample stage with Si substrate was pulse-biased using a separate hard-tube pulser. During the implantation operation, HiPIMS pulse and substrate's negative bias pulse were synchronized at the same frequency of 50 Hz. The pulse voltage applied to the Ge sputtering target was -1200 V and the pulse width was 80 usec. While operating the Ge sputtering gun in HiPIMS mode, a pulse bias of -50 kV was applied to the Si substrate. The pulse width was 50 usec with a 30 usec delay time with respect to the HiPIMS pulse. Ge ion implantation process was performed for 30 min. to achieve approximately 20 % of Ge concentration in Si substrate. Right after Ge ion implantation, ~50 nm thick Si capping layer was deposited to prevent oxidation during subsequent RTA process at $1000^{\circ}C$ in N2 environment. The Ge-implanted Si samples were analyzed using Auger electron spectroscopy, High-resolution X-ray diffractometer, Raman spectroscopy, and Transmission electron microscopy to investigate the depth distribution, the degree of strain relaxation, and the crystalline structure, respectively. The analysis results showed that a strain-relaxed SiGe layer of ~100 nm thickness could be effectively formed on Si substrate by direct Ge ion implantation using the newly-developed PIII&D process for non-gaseous elements.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제30권6호
• /
• pp.497-503
• /
• 2004

One of the most difficult problems to damage in dentistry is an odontogenic infection. These infections may range from low-grade, well-localized infections that require only minimal treatment to a severe, life-threatenig fascial space infection. Although the overwhelming majority of odontogenic infections are easily managed by minor surgical procedures and supportive medical therapy that includes antibiotic administration, the practitioner must constantly bear in mind that these infections may become severe in a very short time. We made an investigation was targeting on 78 male and 47 female patients (125 patients in total) who had been hospitalized because of the fascial space abscess on the oral and maxillofacial area and gained a complete recovery in Daegu Catholic University Hospital, Oral & Maxillofacial Surgery from January 1999 to December 2003. By tracing their charts, we could grasp the characteristics such as age, gender, the time of breakout and specific areas of the attacks, making a conclusive study of the statistical analysis and finally, we could reach conclusions. Now, we report the conclusion from the investigation with the literature. The proportion of males and females was approximately 3 to 2, and in age group, patients under 10 years old marked the highest, 22.4%. The patients between the age of 10 and 40 were only 14.4%, yet those who were between 40 and 80 marked 53.6% in contrast. In the monthly distribution, the order was Dec.(13.6%)-Sep.(12%)-Jan.(10.4%) and in seasonal distribution, it was winter(30.4%)-fall(28%)- summer(24.4%)- spring(19.2%). Considering the medical history, D.M. was the highest which was 30.3%, hypertension marked 24.4%, and the patients with both D.M. and hypertension were 9.0%. The major cause of infection of oral and maxillofacial areas was odontogenic infection, which marked about 96%, and especially the cases related to dental caries occurred most frequently, which was 51.2%. In the number of relaxed fascial space, single fascial space was 81.6%, and in the degree of relaxation of fascial space, the buccal space abscess marked 40.8%, following submandibular space abscess, which was 30.4%.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제26권4호
• /
• pp.604-613
• /
• 2002

Generation characteristics of electrospray droplets for highly viscous liquid have been investigated by measuring size distributions of droplets emitted from the Taylor cone using glycerol solutions with various conductivities. Because of very small volatility of glycerol, droplet sizes can be measured by an aerodynamic size spectrometer (TSI Aerosizer DSP) with negligible evaporation of droplets. For highly conducting and viscous liquid, the sizes of the droplets electrosprayed from the Taylor cone are found to be relatively insensitive to applied voltages and the electrosprays assisted by the corona discharge call produce monodisperse droplets as long as the corona intensity is not too high. Near the minimum flow rate where a liquid cone is stable, the spray tends to consist of a one -peak monodisperse distribution of drop lets. However, at high flow rates, the spray bifurcates into bimodal distributions, which are consistent with the result of the previous study for less viscous liquids than our liquids. For liquid flow rates (Q) below 1 nl/s, the measured droplet diameters by the aerosizer are in the range of 0.30 to 1.2 ${\mu}{\textrm}{m}$ for the glycerol solutions. The diameters of monodisperse droplets scale approximately with $r^*=Q_$\tau$(Q$\tau$){^1/3}$ where $r^*$ is a characteristic length and $\tau$is the electrical relaxation time of the fluid. However, when compared with several represe ntative scaling laws, the droplet diameters are two to six factors greater than those predicted by the scaling laws. This may be closely related to the combined effect of the much higher viscosity and the electrical charge on the jet breakup of glycerol so solution.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제23권12호
• /
• pp.936-941
• /
• 2010

In this study, we have investigated the effects of Mn dopant on the bulk trap levels and grain boundary characteristics of $Bi_2O_3$-based ZnO (ZB) varistor using admittance spectroscopy and dielectric functions (such as $Z^*,\;Y^*,\;M^*,\;\varepsilon^*$, and $tan\delta$). Admittance spectra and dielectric functions show two bulk traps of $Zn_i^{..}$ (0.20 eV) and $V^{\bullet}_o$ (0.29~0.33 eV) in ZnO-$Bi_2O_3-Mn_3O_4$ (ZBM). The barrier of grain boundaries in ZBM could be electrochemically single type. However, its thermal stability was slightly disturbed by ambient oxygen because the apparent activation energy of grain boundaries was changed from 0.79 eV at lower temperature to 1.08 eV at higher temperature. The grain boundary capacitance $C_{gb}$ was decreased slightly with temperature as 1.3~1.8 nF but resistance $R_{gb}$ decreased exponentially. The relaxation time distribution can result from the heterogeneity of the barriers constituting the varistor. It is revealed that Mn dopant in ZB reduced the heterogeneity of the barrier in grain boundaries and stabilized the barrier against the ambient temperature.

• Journal of the Korean Society for Marine Environment & Energy
• /
• 제15권4호
• /
• pp.273-280
• /
• 2012

The numerical simulation using the Lattice Boltzmann Method in the field of computational fluid dynamics becomes wider in the engineering applications because of its simplicity of update rules compared to the conventional Navier-Stokes solvers. Here, a two-dimensional D2Q9 LB model is numerically tested with a few new computational treatment on the free surface. The single relaxation time is applied under the gravitational field where applied only in the higher density fluid because of its big density difference. At the free surface, the reconstruction techniques in combination with boundary conditions is adopted in order to get some distribution function coming into the fluid site from the air one, and surface tension, early stable test for the gravitional field is considered in it. With the implementation of the gravitational profile, conserving the overall mass and grid dependency are observed during the calculations and freesurface advance track is well captured with an experiment.