• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.62 no.1
• /
• pp.36-44
• /
• 2013

This paper is written for the development and application of boiler fuel control algorithm and distributed control system of coal-fired power plant by the steps of design, coding, simulation test, site installation and site commissioning test. Fuel control algorithm has the upper algorithm and it is boiler master control algorithm that controls the fuel, feed water, air by generation output demand. Generation output demand by power load influences fuel control. Because fuel can not be supplied fast to the furnace of boiler, fuel control algorithm was designed adequately to control the steam temperature and to prevent the explosion of boiler. This control algorithms were coded to the control programs of distributed control systems which were developed domestically for the first time. Simulator for coal-fired power plant was used in the test step. After all of distributed control systems were connected to the simulator, the tests of the actual power plant were performed successfully. The reliability was obtained enough to be installed at the actual power plant and all of distributed control systems had been installed at power plant and all signals were connected mutually. Tests for reliability and safety of plant operation were completed successfully and power plant is being operated commercially. It is expected that the project result will contribute to the safe operation of domestic new and retrofit power plants, the self-reliance of coal-fired power plant control technique and overseas business for power plant.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1982-1985
• /
• 2003

Future cellular networks will mainly be driven by, high quality channels, high band with utilization, low power consumption and efficient network management. For a given channel allocation, the capacity and quality of communication of cellular radio systems using CDMA(Code Division Multiple Access) can be increased by using a transmitter power control scheme to combat the near-far problem. Centralized power control schemes or distributed ones to maximize the minimum signal-to-interference in each user of CDMA wireless network have been investigated. This paper has proposed a distributed power control algorithm, which employs an adaptive search scheme, in order to solve quickly the linear systems of equations for power update in CDMA cellular radio systems. The simulation results show that the proposed scheme has faster convergence rate than the typical bang-bang type of distributed power control algorithm, which has been much used as a reference algorithm in IS-95A and W-CDMA communication network.

• Journal of Communications and Networks
• /
• v.5 no.3
• /
• pp.197-201
• /
• 2003

We study in this paper both distributed power control and removal algorithms for multimedia CDMA wireless networks. In our study, users can have different data rates as well as different quality of service (QoS) requirements. We derive a necessary and sufficient condition for the fully distributed power control (FDPC) algorithm to find a feasible power set. We also prove that, if the maximal power level is used at the start, then the distributed constrained power control (DCPC) algorithm is equivalent to the FDPC algorithm. For the connection removal algorithm, we prove that the non-reinitialized removal algorithm finds a feasible power set faster and employs smaller power levels than the reinitialized one does. Performances of some connection removal criteria are also studied. Our simulation results reveal that the smallest normalized CIR (SNC) and largest CIR requirement (LCR) criteria result in smaller outage probability than the smallest CIR (SC) criterion in a multimedia environment.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.62 no.3
• /
• pp.117-126
• /
• 2013

This paper is written for the development and application of boiler furnace pressure control algorithm and distributed control system of coal-fired power plant by the steps of design, coding, simulation test, site installation and site commissioning test. The control algorithms were designed in the shape of cascade control for two parts of furnace pressure control and induced draft fan pitch blade by standard function blocks. This control algorithms were coded to the control programs of distributed control systems. The simulator for coal-fired power plant was used in the test step and automatic control, sequence control and emergency stop tests were performed successfully like the tests of the actual power plant. The reliability was obtained enough to be installed at the actual power plant and all of distributed control systems had been installed at power plant and all signals were connected mutually. Tests for reliability and safety of plant operation were completed successfully and power plant is being operated commercially. It is expected that the project result will contribute to the safe operation of domestic new and retrofit power plants, the self-reliance of coal-fired power plant control technique and overseas business for power plant.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.95_96
• /
• 2009

In this paper, a new algorithm of Integrated Volt/Var Control (IVVC) is proposed using Volt/Var control for the Distribution Automation System (DAS) based on the modeling of the distributed load and the distributed current. In the proposed, the load flow based on the modeling of the distributed load with Distributed Generation and the distributed current are estimated from constants of four terminals using the measurement of the current and power factor from a Feeder Remote Terminal Unit (FRTU). For Integrated Volt/Var Control (IVVC), the gradient method is applied to find optimal solution for tap and capacity control of OLTC (On-Load Tap Changers), SVR (Step Voltage Regulator), and SC (Shunt Condenser). What is more Volt/Var control method is proposed using moving the tie switch as well as IVVC algorithm using power utility control. In the case studies, the estimation and simulation network have been testified in Matlab Simulink.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.5
• /
• pp.345-351
• /
• 2018

A distributed control method is proposed to improve the power sharing performance of bidirectional distributed generators and the voltage regulation performance of a DC bus in a DC microgrid. Voltage sensitivity analysis based on power flow analysis is conducted to analyze the structural characteristics of a DC microgrid. A distributed control method using a voltage sensitivity matrix is proposed on the basis of this analysis. The proposed method uses information received through the communication system and performs the droop gain variation method and voltage shift method without additional PI controllers. This approach achieves improved power sharing and voltage regulation performance without output transient states. The proposed method is implemented through a laboratory-scaled experimental system consisting of two bidirectional distributed generators, namely, a load and a non-dispatchable distributed generator in a four-bus ring-type model. The experimental results show improved power sharing accuracy and voltage regulation performance.

• Journal of Information Processing Systems
• /
• v.18 no.6
• /
• pp.784-793
• /
• 2022

Grid-connected distributed power generation has been widely used in green energy generation. However, due to the distributed characteristics, distributed power generation is difficult to be dynamically allocated and monitored in the electrical control process. In order to solve this problem, this research combined the Internet of Things (IoT) with the automatic control system of electrical engineering to improve the control strategy of the power grid inverter according to the characteristics of the IoT system. In the research, a connection system of the power grid inverter and the IoT controller were designed, and the application effect was tested by simulation experiments. The results showed that the power grid inverter had strong tracking control ability for current and power control. Meanwhile, the electrical control system of the IoT could independently and dynamically control the three-phase current and power. The given value was reached within 50 ms after the step signal was input, which could protect the power grid from being affected by the current. The overall system could realize effective control, dynamic control and protective control.

• Journal of Electrical Engineering and Technology
• /
• v.3 no.2
• /
• pp.143-151
• /
• 2008

This paper presents the operation of Fuel Cell Distributed Generation(FCDG) systems in distribution systems. Hence, modeling, controller design, and simulation study of a Solid Oxide Fuel Cell(SOFC) distributed generation(DG) system are investigated. The physical model of the fuel cell stack and dynamic models of power conditioning units are described. Then, suitable control architecture based on fuzzy logic and the neural network for the overall system is presented in order to activate power control and power quality improvement. A MATLAB/Simulink simulation model is developed for the SOFC DG system by combining the individual component models and the controllers designed for the power conditioning units. Simulation results are given to show the overall system performance including active power control and voltage regulation capability of the distribution system.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.6
• /
• pp.1261-1268
• /
• 2013

This study proposes a voltage and reactive coordinative control strategy with distributed generator (DG) in a distribution power system. The aim is to determine the optimum dispatch schedules for an on-load tap changer (OLTC), distributed generator settings and all shunt capacitor switching on the load and DG generation profile in a day. The proposed method minimizes the real power losses and improves the voltage profile using squared deviations of bus voltages. The results indicate that the proposed method reduces the real losses and voltage fluctuations and improve receiving power factor. This paper proposes coordinated voltage and reactive power control methods that adjust optimal control values of capacitor banks, OLTC, and the AVR of DGs by using a voltage sensitivity factor (VSF) and dynamic programming (DP) with branch-and-bound (B&B) method. To avoid the computational burden, we try to limit the possible states to 24 stages by using a flexible searching space at each stage. Finally, we will show the effectiveness of the proposed method by using operational cost of real power losses and voltage deviation factor as evaluation index for a whole day in a power system with distributed generators.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2121-2125
• /
• 2003

This paper proposes a fast distributed constrained power control (FDCPC) with non-stationary relaxation factor to next power update in CDMA cellular power control system. We review unconstrained control algorithms, the distributed power control (DPC), unconstrained second order power control (USOPC) and DPC with stationary relaxation factor (DPCSRF). Under the unconstrained condition, the convergence analysis shows theoretically that the convergence rate of DPC is the fastest one. However, under the constrained control algorithms, DCPC is not the fastest one any more because of transmission power constraint. To improve the convergence speed, the DCPC with non-stationary relaxation factor (FDCPC) are proposed. Under the constrained condition, the convergence rate of FDCPC outperforms that of DCPC and CSOPC.