• Computers and Concrete
• /
• v.6 no.4
• /
• pp.319-341
• /
• 2009

A new formulation based on lumped plasticity and inelastic hinges is presented in this paper for nonlinear analysis of Reinforced Concrete (RC) frame structures. Inelastic hinge behaviour is described using the principles of Continuum Damage Mechanics (CDM). Member formulation contains provisions to model stiffness degradation due to cracking of concrete and yielding of reinforcing steel. Depending on its nature, cracking is classified as concentrated or distributed. Concentrated cracking is accounted through a damage variable and its growth is defined based on strain energy principles. Presence of distributed flexural cracks in a member is taken care of by modelling it as non-prismatic. Plasticity theory supported by effective stress concept of CDM is applied to describe the post-yield response. Nonlinear quasi-static analysis is carried out on a RC column and a wide two-storey RC frame to verify the formulation. The column is subjected to constant axial load and monotonic lateral load while the frame is subjected to only lateral load. Computed results are compared with those due to experiments or other numerical methods to validate the performance of the formulation and also to highlight the contribution of distributed cracking on global response.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.5
• /
• pp.448-457
• /
• 2013

This paper proposes a control method under stand-alone operating mode for distributed-module type photovoltaic power conditioners. In conventional schemes, there are some problems of a controller saturation in the DC-link (or load) voltage controller when overly-heavy load, light load, and the generated PV power reduction occurs, as well as when a transition occurs from an overly-loaded to normal conditions. To overcome these problems, the proposed controller method switches the main control target from DC-link voltage to the maximum power point, which is closer to the stable operating point when it returns to normal operating conditions. For the analysis, a state-plane trajectory was given and the circuit analysis by PSIM simulation was done. For the verification, a prototype hardware with 110[W] and 50[W] dual photovoltaic modules has been implemented. From the results, it can be seen that PV power tracking is successfully done with the proposed method even under a stand-alone operation mode.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.7
• /
• pp.1193-1203
• /
• 2016

This paper proposes a droop control scheme to compensate the unbalanced line-to-line voltage of unbalanced 3-phase load which is coupled with two inverter-based distributed generations through unequal impedance lines. Unbalanced line-to-line load voltages occur due to using single-phase loads, which brings about bad effects on the coupled inverters and the distributed generations. In order to compensate the unbalanced line-to-line voltages, a positive sequence voltage control was used for sharing the active and reactive power and a negative sequence control was used for reducing the negative sequence voltage. The feasibility of the proposed scheme was first verified by computer simulations, and then experiments with a hardware set-up built in the lab. The experimental results were compared with the simulation results to confirm the feasibility of the proposed scheme.

• Structural Engineering and Mechanics
• /
• v.82 no.3
• /
• pp.401-416
• /
• 2022

The aim of this study is to examine the frictionless double receding contact problem for two functionally graded (FG) layers pressed with a uniformly distributed load and resting on a homogeneous half plane (HP) using analytical and numerical methods. The FG layers are made of a non-homogeneous material with an isotropic stress-strain law with exponentially varying properties. It is assumed that the contact at the FG layers and FG layer-HP interface is frictionless. The body force of the FG layers and homogeneous HP are ignored in the study. Firstly, an analytical solution for the contact problem has been realized using the theory of elasticity and the Fourier integral transform techniques. Then, the problem modeled and two-dimensional analysis was carried out by using the ANSYS package program based on FEM. Numerical results for contact lengths and contact pressures between FG layers and FG layer-HP were provided for various dimensionless quantities including material inhomogeneity, distributed load width, the shear module ratio, and the heights of the FG layers for both methods. The results obtained using FEM were compared with the results found using the analytical formulation. It was found that the results obtained from analytical formulation were in perfect agreement with the FEM study.

• Journal of the Korea Society of Computer and Information
• /
• v.14 no.8
• /
• pp.89-96
• /
• 2009

In the future energy environment, a power information system will meet the real-time capability to process the emergency events, unexpected blackouts or over-load, and the high performance to provide the consumer service events such as remote meter reading. In addition to, it must have facility which is able to process a large information occurred on system effectively. In this paper, we developed a distributed power information system based on event with metadata processing technique which was both load balancing and decreased hot spot using XML that was efficient for information exchange. In order to experiment, we made a reduced future power system with controling power device using wireless communications and we could do experiments through it.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.3
• /
• pp.513-521
• /
• 2017

Robust optimal operation of a microgrid is required since the increase of the penetration level of renewable generators in the microgrid raises uncertainty due to their intermittent power output. In this paper, an application of probabilistic optimization method to economical operation of a microgrid is studied. To simplify the treatment of the uncertainties of renewable generations and load, the new 'band of virtual equivalent load variation' is introduced considering their uncertainties. A simplified robust optimization methodology to generate the scenarios within the band of virtual equivalent load variation and to obtain the optimal solution for the worst scenario is presented based on Monte Carlo method. The microgrid to be studied here is composed of distributed generation system(DGs), battery systems and loads. The distributed generation systems include combined heat and power(CHP) and small generators such as diesel generators and the renewable energy generators such as photovoltaic(PV) systems and wind power systems. The modeling of the objective function for considering interruption cost by the penalty function is presented. Through the case study for a microgrid with uncertainties, the validity of proposed robust optimization methodology is evaluated.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.3
• /
• pp.83-91
• /
• 2021

A crawler crane, which consists of a lattice boom, a driving system, and a movable vehicle, is widely used on construction sites. The crawler crane often traverses rough terrain at these sites; as a result, an overload limiter needs to be installed on the crane to prevent it from overturning and breaking. In this paper, we studied the distributed load change in relation to boom length and the angle of rotation of the roller that comes in direct contact with the grounded track shoe. First, we developed a 3D model of a crawler crane and meshed it for finite elements. Then, we performed finite element analysis to derive the load on the roller. Finally, we graphed and examined the roller distributed load data of the case according to boom length and rotation angle. By detecting the load on the roller of the crawler crane, we can predict the potential for the crane to overturn before it happens.

• Steel and Composite Structures
• /
• v.41 no.5
• /
• pp.637-648
• /
• 2021

Nowadays, one of the practical, fast and easy ways to strengthen steel elements is the use of Carbon Fiber Reinforced Polymer (CFRP). Most previous research in the CFRP strengthening of steel members has carried out on straight steel members. The main difference between horizontal curved beams and straight beams under vertical load is the presence of torsional moment in the horizontal curved beams. In the other words, the horizontal curved beams are analyzed and designed for simultaneous internal forces included bending moment, torsional moment, and shear force. The horizontal curved steel beams are usually used in buildings, bridges, trusses, and others. This study explored the effect of the CFRP strengthening on the behavior of the horizontal curved square hollow section (SHS) steel beams. Four specimens were analyzed, one non-strengthened curved steel beam as a control column and three horizontal curved steel beams strengthened using CFRP sheets (under concentrated load and uniform distributed load). To analyze the horizontal curved steel beams, three dimensional (3D) modeling and nonlinear static analysis methods using ANSYS software were applied. The results indicated that application of CFRP sheets in some specific locations of the horizontal curved steel beams could increase the ultimate capacity of these beams, significantly. Also, the results indicated when the horizontal curved steel beams were under distributed load, the increase rate in the ultimate capacity was more than in the case when these beams were under concentrated load.

• KIISE Transactions on Computing Practices
• /
• v.22 no.2
• /
• pp.101-106
• /
• 2016

A femtocell network has been attracting attention as a promising solution for providing high data rate transmission over the conventional cellular network in an indoor environment. In this paper, we propose a distributed power control algorithm considering both indoor coverage and data load balancing in the femtocell network. As data traffic varies by time and location according to user distribution, each femto base station suffers from an unbalanced data load, which may degrade network performance. To distribute the data load, the base stations are required to adjust their transmission power dynamically. Since there are a number of base stations in practice, we propose a distributed power control algorithm. In addition, we propose the simple algorithm to detect the faulty base station and to recover coverage. We also explain how to insert a new base station into a deployed network. We present the simulation results to evaluate the proposed algorithms.

• Journal of the Korea Society of Computer and Information
• /
• v.16 no.8
• /
• pp.11-18
• /
• 2011

The increasing of web users load to the excessive transmission traffic and system overload problems. To solve these problems, cluster systems are studied. In conventional cluster systems, when the request size is large owing to such types as multimedia and CGI, the particular server load and response time tend to increase even if the overall loads are distributed evenly. In this paper, we consider the methodology of efficient resource usage, specially distributed web cluster system. We develope an algorithm that distributes the load on the web cluster system to use the system resources, such as system memory equally. The response time is chosen as a performance measure on the various clustering models. And based on the concurrent user to the web cluster system, the response time is also examined as the number of users increases. Simulation experience with this algorithm shows that the response time and average throughput seems to have a good results compare to those with the other algorithm.