• Journal of Welding and Joining
• /
• 제34권5호
• /
• pp.33-40
• /
• 2016

The microstructures and the creep rupture properties of dissimilar welds between the Ni-based superalloy Inconel 740H and the non-stabilized austenitic stainless steel TP316H have been characterized. The welds were produced by shielded metal arc (SMA) welding process with the AWS A5.11 Class ENiCrFe-3 filler metal, commonly known as Inconel 182 superalloy. Postweld heat treatment at $760^{\circ}C$ for 4 hours was conducted to form ${\gamma}^{\prime}$ strengthener in Inconel 740H. The austenitic weld metal produced by Inconel 182 had a dendritic microstructure, and grew epitaxially from the both sides of Inconel 740H and TP316H base metals. Since both Inconel 740H and TP316H did not undergo any solid-state transformation during welding process, there were no heat-affected-zone (HAZ) sub-regions and the coarsoned grains near the weld interface were limited to a narrow region. The hardness of Inconel 182 weld metal was ~220 Hv. The gradual hardness decrease was detected at HAZ of TP316H, and the TP316H base metal displayed the lowest hardness value (~180 Hv) whilst the Inconel 740H showed the highest hardness value (~400 Hv). Fracture after creep occurred at the center of weld metal, regardless of creep condition. It was found that during creep the cracks initiated and propagated along interdendritic regions and grain boundaries at which Laves particles enriched in Nb, Si and Cr were present. The appropriate design of weld metal was discussed to suppress the creep-induced cracking of the present dissimilar weld.

• 대한기계학회논문집A
• /
• 제36권8호
• /
• pp.929-934
• /
• 2012

본 연구에서는 레이저 TWB로 용접된 이종재료의 동적 특성에 대한 해석이 수행되었다. 해석프로그램은 Hyper works 10.0으로 Solver는 LS-DYNA v.971, 모델링 요소는 2D-Shell, 요소 수는 35,641개, 노드 수는 36,561개이다. 충격속도는 10 km/h이다. 상 하부의 용접선 높이에 따르는 영향을 연구하기 위하여, 하부의 길이를 300 mm와 400 mm로 하였다. 얻어진 결론은 다음과 같다. 길이 300 mm인 하부 재료 SPFC980의 변형은 가장 작고, 충돌 흡수 에너지는 가장 크다. 하부 냉연강 기준으로 TWB의 위치가 짧을수록 성능이 우수하게 나타났다. 즉, 상대적으로 상부 고강도강인 SABC1470 재료가 차지하는 비율에 따라 성능이 좌우되었다. 하부 재료 SPFH590은 큰 변형이 나타났고, 충돌성능은 SPFC980보다 현저히 떨어졌다. 따라서 충돌 성능 해석 결과에서 하부 재료 SPFC980인 길이 300 mm가 가장 우수한 것으로 나타났다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2008년도 춘계학술발표대회 개요집
• /
• pp.2-2
• /
• 2008

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2005년도 춘계학술발표회
• /
• pp.871-872
• /
• 2005

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.152-154
• /
• 2005

Austenitic stainless steel has good weldability but is sensitive to hot cracking such as solidification crack and liquation crack. In this study, the specimens of dissimilar metals made between austenitic stainless steel and Al-brass were welded by GTAW process using four different filler metals. Cracks were detected in the heat-affected zone of the stainless steel when welded with CuAl, CuSn and NiCu filler metals, but no cracks were detected a Ni filler metal was used. The cracks propagated along the grain boundary in the heat affected zone near the fusion line to base metal of 316L stainless steel. The cracks were located inside the weld bead with very fine hairline crack. All cracks initiated at the fusion line and moved forward in the base metal. From energy dispersion spectroscopy (EDS), Cu peak was detected only in the crack-opening area.

• International Journal of Korean Welding Society
• /
• 제3권2호
• /
• pp.46-52
• /
• 2003

The refinement of microstructure and phase transformation near the interface of pure copper/carbon steel dissimilar metals joints with various friction welding parameters have been studied in this paper. The microstructure of copper and carbon steel joints were changed to be a finer grain compared to those of the base metals due to the frictional heat and plastic deformation. The microstructure of copper side experienced wide range of deformed region from the weld interface and divided into very fine equaxied grains and elongated grains. Especially, the microstructures near the interface on carbon steel were transformed from ferrite and pearlite dual structure to fine ferrite, grain boundary pearlite and martensite due to the welding thermal cycle and rapid cooling rate after welding. These microstructures were varied with each friction welding parameters. The recrystallization on copper side is reason for softening in copper side and martensite transformation could explain the remarkable hardening region in carbon steel side.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.331-336
• /
• 2004

Dissimilar friction welding were produced using 10mm and 11mm diameter solid bar in Inconel ally(IN X-750) to Stainless steel(STS316L) to investigate their mechanical properties. The main friction welding parameters were selected to endure good quality welds on the basis of visual examination, tensile tests, Virkers hardness surveys of the bond of area and HAZ and macro-structure investigations. The specimens were tested as welded, not heat-treated. The tensile strength of the friction welded steel bars was increased up to $95\%$ of the STS316L base metal under the condition of all heating time. Optimal welding conditions were n=2,000(rpm), $P_1=220(MPa),\;P_2=260(MPa),\;t_1=4(s),\;t_2=4(s)$ when the total upset length is 7(mm).

• 한국해양공학회지
• /
• 제13권3호통권33호
• /
• pp.83-91
• /
• 1999

Taking a view of joining by welding the IN713C to SCM440 and SCM415 steel in production of turbochargers, the frictin welding process may be utilized as a new approach for joining them of other conventional welding processes. It is because the friction welding has more technical and technical and economic advantages than the other welding processes. As this welding process has the characteristics such as curtaliment of production time and materials and cost reduction, etc.. So, this paper deals with determining the preper friction welding condition and analyzing various mechanical properties of friction welded joints of the super heat resisting steel to alloy stee(IN713C to SCM440 and SCM415). And the in-process real-time weld quality evaluation technique by acoustic emission during friction welding of IN713C to SCM440 and SCM415 steels with higher confidence and relibility has been much required even though it might be the first trial approach for developing it. Then, this first study aimed to develop the optimization of dissimilar friction welding of heat resisting steels (INC713 to SCM440, SCM415) for turbine, considering on strength and toughness.

• 한국생산제조학회지
• /
• 제21권3호
• /
• pp.433-438
• /
• 2012

We have studied on welding dissimilar materials of Carbon steel SCP1-S by using laser beam. In this research we have performed some experiments to know the possibility of welding dissimilar materials using laser beam and magnetic fields by adjusting the power output of 35W laser. Other conditions of the experiments were as follows : the welding speed was varied in the range 10 m/min nitrogen gas was used as shield gas, the flow value of shield gas was ranged 10 L/min. In order to ascertain of the welded surface, we have done the tensile strength testing, the hardness testing and the microscope observation. As a result, we have found that tensile strength was the highest at the condition of the welding speed of 10mm/s, the flow value of 10 L/min, the gap of two materials 0, and the use of nitrogen gas. Above testings have also showed that the tensile strength was generally satisfactory since the penetration of welding was almost complete due to the thinness of the materials. In addition, the formation of the welded area was excellent when it had the highest tensile strength.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권1호
• /
• pp.68-74
• /
• 2011

본 논문은 LNG 선박의 이중연료엔진의 이중벽 가스파이프의 재료인 STS 304와 STS 316L에 대하여 GTAW에 의해 용접된 동종 및 이종 용접부의 기계적 특성과 용접성을 평가하였다. STS 304 동종 용접부의 경우, STS 316L 동종 용접부에 비해 모재 대비 현저하게 기계적 특성이 감소하는 경향을 나타냈다. 미세조직 관찰 결과, STS 304 동종 용접부가 STS 316L 동종 용접부에 비해 침상 페라이트가 많이 형성되어 상대적으로 높은 경도를 나타냈다.