• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.1
• /
• pp.19-26
• /
• 2016

In this study, a bidirectional DC-DC converter for idle stop and go (ISG) is developed to reduce fuel consumption. A three-phase non-isolated half-bridge converter is selected through a design method by considering efficiency and volume. According to the state of charge of the batteries at both the low-voltage and high-voltage sides, buck mode, which charges a low-voltage battery from the generated motor energy, and boost mode, which provides power to the motor from the low- and high-voltage battery sides, are required in the ISG system. Hence, an autonomous and seamless bidirectional control method using a variable current limiter is proposed for mode change. A 1.8 kW engineering sample of the proposed converter has been built and tested to verify the validity of the proposed concept. The maximum efficiencies, including gate driver and control circuit losses, are 96.4% in charging mode and 96.1% in discharging mode.

• Proceedings of the KIPE Conference
• /
• 2011.11a
• /
• pp.157-158
• /
• 2011

This paper deals with the minimization of switching loss of a dual full-bridge bidirectional DC-DC converter for supercapacitor. In case of charging mode the switching loss can be minimized with proper switching pattern, and the switching loss in discharging mode can be minimized with soft switching. Simulation results show that the switching loss is reduced considerably.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.6
• /
• pp.467-473
• /
• 2001

BMS(Battery Management System) in EV system(Electric Vehicle) senses voltage, temperature and the charging or discharging current of batteries. The main roles of BMS are to estimate SOC(State OF Charge) of batteries and optimally monitor them according to the operation state of EV system which is motoring mode or charging mode. In this paper, we propose the proper algorithm about BMS's roles and operation which is suitable to EV system and illustrate validity and effectiveness through the experiments which were performed in the condition of Vehicle road test and charging test.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.292-292
• /
• 2010

Bimodal Tram is driven by both engine and Lithium Polymer battery pack which consists with 168 cells of LPB(80Ah, 650Vdc). LPB pack is very frequently charged and discharged in driving. Temperature inside of LPB pack makes an great effect on both charging and discharging capacity which seem to be related with LPB internal resistance. LPB internal resistance is increasing or little decreasing with the decreased temperature under 10 - $20^{\circ}C$ and the increased temperature over $30^{\circ}C$ which is similar to the temperature characteristics of single LPB cell. This paper has analyzed the driving characteristics of LPB pack for bimodal tram is running with either battery mode or hybrid mode.

• Journal of Power Electronics
• /
• v.12 no.3
• /
• pp.487-494
• /
• 2012

A new low cost high power density photovoltaic power conditioning system (PV PCS) with an energy storage system is proposed in this paper. Its high power density and cost effectiveness can be achieved through the unification of the maximum power point tracker and the battery charger/discharger. Despite the reduced power stage, the proposed system can achieve the same performance in terms of maximum power point tracking and battery charging/discharging as the conventional system. When a utility power failure happens, the proposed system cannot perform maximum power point tracking at the UPS mode. However, the predetermined battery voltage near the maximum power point of the PV array can effectively generate a reasonable PV power even at the UPS mode. Therefore, it features a simpler structure, less mass, lower cost, and fewer devices. Finally, to confirm the operation, validity, and features of the proposed system, a theoretical analysis and experimental results from a single phase AC 220Vrms/1.5kW prototype are presented.

• Journal of ILASS-Korea
• /
• v.12 no.3
• /
• pp.138-145
• /
• 2007

In the present work, the breakup mechanism of highly viscous epoxy paints discharged from a fan spray nozzle was examined experimentally. The paints tested were non-Newtonian fluids, composed of epoxy resin, solid particles and other additives. The paint spray discharged from the nozzle was visualized and recorded using a digital camera with back illumination. Due to presence of the solid particles, perforation of liquid sheet was observed in most cases, even at low-Reynolds number conditions (Re < 15,000) where the aerodynamic-wave breakup mode is used to be dominant for pure liquids. However, with the increase of the particle concentration, the sheet became longer and the thickness at breakup became thinner to some extent. This is because, with higher concentration of solid particles, the stabilizing effect by the viscosity increase predominates over the destabilizing effect by perforation.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.672-676
• /
• 2009

Polymide is widely used alignment material of recent commercial LCD panel structure. Generally, polyimide alignment material is classified soluble polyimide type and polyamic acid type with their main bond structure of solution state. specially, compared to polyamic acid alignment layer, soluble polyimide type alignment layer have excellent reliability during long term LCD driving cause of their high imidazation ratio(%), high voltage holding ratio(%) and low ion density. The other side, this type alignment materials has significant DC image stickicng side effect for using in-plane switching mode lcd structure cause of their slow DC discharging property. we applied inorganic salt to usual soluble polyimide type alignment layer and found out this technique had good DC image sticking property without any loss of reliability property in inplane switching LCD cell structure. This approach leads excellent DC image sticking property with maintaining high reliability property this approach confirmed improves an image sticking and a reliability simultaneously from the horizontality aligned LCD mode whose relatively bad image sticking property.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.11 no.6
• /
• pp.815-823
• /
• 1999

A dynamic simulation program may be used for the development of effective control algorithms for the ice storage cooling system. Simplified effective dynamic models for an ice-on-coil type storage tank, a screw chiller, a water-to-air heat exchanger, three way valves, pipes, pumps, temperature sensors, and controllers were developed. And a dynamic simulation program for the ice storage cooling system was developed by using these dynamic models. Control algorithms for the full storage system were also selected and analyzed in order to show the effectiveness of these models. From the simulation results, it may be concluded that the simulation program developed in this study can be effectively used for the development of improved control algorithms for the ice storage cooling system.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1257-1259
• /
• 2004

This paper deals with the operation of a flywheel energy storage UPS. The operating principle of the UPS is analysed in each mode including charging, voltage compensation, discharging, and voltage unbalance compensation. The usefulness of the operation is proved through simulations.

• Journal of Power Electronics
• /
• v.10 no.2
• /
• pp.181-186
• /
• 2010

This paper presents a new method for the estimation of State of Charge (SOC) for NiMH batteries. Among the conventional methods to estimate SOC, Coulomb Counting is widely used, but this method is not precise due to error integration. Another method that has been proposed to estimate SOC is by using a measurement of the Open Circuit Voltage (OCV). This method is found to be a precise one for SOC estimation. In NiMH batteries, the hysteresis characteristic of OCV is very strong compared to other type of batteries. Another characteristic of NiMH battery to be considered is that the OCV of a NiMH battery under discharging mode is lower than it is under charging mode. In this paper, the OCV is modeled by a simple method based on a hyperbolic function which well known as Takacs’s model. The OCV model is then used for SOC estimation. Although the model is simple, the error is within 10%.