• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2005년도 전력전자학술대회 논문집
• /
• pp.376-379
• /
• 2005

High efficiency and low cost sustain driver for plasma display panel (PDP) with current fed is proposed. Main concept of the proposed circuit is using the current source to charge and discharge panel. As a result, all power switches can achieve the zero voltage switching (ZVS) and every auxiliary switch can also do the zero current switching (ZCS). Moreover, since the inductor current can compensate the discharge current, the current stress of all power switches can be reduced considerably. Furthermore, it has features as a simpler structure, less mass, less cost, and lower electromagnetic interference than prior circuit.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 춘계학술대회 논문집
• /
• pp.207-210
• /
• 1998

Surface electrical conduction in insulator is most important factor to assess the insulation performances of outdoor insulating materials. In this paper, contamination performance of the widely used materials for outdoor insulator - porcelain, EPDM, Silicone rubber - were discussed by measuring properties of average leakage current and scintillation discharge pulses under artificial contamination conditions. The artificial contaminations used were deionized distilled water fog, 0.5wt% NaCl salt fog of light pollution and 2wt% NaCl salt fog of medium pollution. The average leakage current was appeared linearly with applied voltage at dry and clean surface condition. The magnitude of leakage current was almost same at different kinds of samples. In case of deionized distilled water fog, the characteristics of leakage current and applied voltage was most different to that in case of dry and clean condition. In case of salt fog pollution condition. The leakage current was increased above critical voltage. The scintillation discharges were also activated at the level the leakage current and scintillation discharges were increased with increasing pollution degree. The resistance to pollution properties of silicone rubber appeared excellent among them.

• 한국환경과학회지
• /
• 제24권4호
• /
• pp.371-381
• /
• 2015

In the mountain streams in Jeju Island, strong turbulence and roughness usually made it nearly impossible to utilize most of intrusive instrumentation for streamflow discharge measurements. Instead, a non-intrusive fixed electro-magnetic wave surface velocimetry (fixed EWSV: Kalesto) became alternatively popular in many representative streams to measure stream discharge seamlessly. Currently, Kalesto has shown noteworthy performance with little loss in flood discharge measurements and also has successfully provided discharge for every minute. However, Kalesto has been operated to regard its measured one-point velocity as the representative mean velocity for the given cross-section. Therefore, it could be highly possible to potentially encompass discharge measurements errors. In this study, we analyzed the difference between such Kalesto discharge measurements and other alternative concurrent discharge measurements such as Acoustic Doppler Current Profiler (ADCP) and mobile EWSV which were able to measure velocity in multi-points in the cross-section. Consequently, Kalesto discharge deviated from ADCP discharge in amount of 48% for relatively low flow, and more than 20% difference for high flow compared with mobile EWSV discharge measurements. These results indicated that the one-point velocity measured by Kalesto should be used as a cross-sectional mean velocity, rather it should be accounted for as an index-velocity in conjunction with directly measured cross-sectional mean velocity by using more reliable instrumentations. After inducing Kalesto Discharge Correction Coefficient (KDCC) that actually means relationship between index velocity and cross-sectional mean velocity, the corrected discharge from Kalesto was significantly improved. Therefore, we found that index velocity method should be applied to obtain better accuracy of discharge measurement in case of Kalesto operation.

• 전기화학회지
• /
• 제19권3호
• /
• pp.114-121
• /
• 2016

본 연구에서는 리튬이온전지의 충방전시 발생하는 발열특성을 CFD 모델링하고, 발열에 따른 충방전 특성을 해석하였다. 리튬이온전지는 직교 파우치형 구조로서 두께방향으로의 1차원계로 설정하여, 전류밀도 방정식, 열 및 물질전달 지배방정식을 도입하였다. Cut-off 전압이 3 V에서 충방전 전류밀도가 1C($17.5A/m^2$), 3C($52.5A/m^2$) 와 5C($87.5A/m^2$)에 대하여, 298K의 등온계와 충방전 전류밀도 별 발열계로 각각 설정하였다. 등온계와 발열계에서 모두 충방전 전류밀도가 높을수록 전지의 용량은 감소되는 것으로 나타났다. 등온계에 비하여 발열계에서 충방전 시간이 증가하였으며, 이는 발열에 의한 온도의 증가로 인해 전극의 평형전위가 감소하고, 리튬이온의 확산계수가 증가하기 때문인 것으로 고려된다. 또한, 리튬이온전지의 충전과 방전에 의한 열 발생 영향을 제어하기 위한 냉각효과를 분석하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 E
• /
• pp.1752-1754
• /
• 1997

The Kaufman type ion beam source with focusing lens was prepared to measure $\gamma$-coefficient of MgO thin film. Initial discharge of the system was started with the discharge voltage of 25V, the cathode filament current of 5.5A at the constant magnetic field of 150G. The system shows the maximum ion current density of $120{\mu}A/cm^2$, energy dispersion of 200eV and beam divergence of $30^{\circ}$ under the condition of Ar gas pressure $2.5{\times}10^{-4}Torr$, the beam voltage of 500V, the discharge voltage of 90V, the accelerator voltage of -200V and the cathode filament current of 6.1A. When the focusing lens was installed onto the ion beam source, the spreadness diameter of ion beam was about 10mm.

• 전력전자학회논문지
• /
• 제10권2호
• /
• pp.203-210
• /
• 2005

IMT2000과 같은 휴대용 무선통신 시스템을 위한 혼성마이크로 동력원에 대한 연구를 수행하였다. 혼성마이크로 동력원은 태양전지, 슈퍼커패시터, 리튬이온 전지로 이루어져 있다. 주기적인 펄스성 부하에 대응하기 위하여, 슈퍼 커패시터가 리튬이온 전지와 병렬로 연결되어 펄스전류를 흡수한다. 태양전지는 배터리에 전류를 공금하며, 최대전력점에서 동작하도록 제어된다. 펄스성 부하에도 적용될 수 있는 최대전력점 추적기법이 소개되며, 실험을 통해서 완벽한 추적성능을 입증하였다. 혼성마이크로 동력원들 간의 매칭을 위한 제어기 설계 기법이 제시되며, 실험을 통해 성능을 입증하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 방전 플라즈마 유기절연재료 초전도 자성체연구회
• /
• pp.120-124
• /
• 2004

The protection performance and energy absorption capability are important for both MOAs for distribution lines and MOAs for high voltage systems, therefore the manufacturing technique of ZnO varistor elements with high ability against surge impacts is great important for high voltage systems. But until now ZnO varistors for low voltage class have been developed in Korea, ZnO varistors with the rate discharge current of 5, 10kA class for high voltage systems depend on an import from advanced countries, such as Japan or U.S.A, which have developed its in the late 1980s. So in the aspect of taking independent technique the development of ZnO varistors with the rate discharge current of 5, 10kA class for high voltage systems is important. In this research project ZnO varistor elements with diameters of 35mm and 70mm for the rate discharge current of 5, 10kA class for high voltage systems are manufactured, then various chemical composition and processing variables affected the electrical and the physical characteristics of these ZnO varistors are investigated.

• 한국위성정보통신학회논문지
• /
• 제7권2호
• /
• pp.18-24
• /
• 2012

본 논문에서는 ESD 방지를 위한 최적 방법론에 목표하여 확장된 드레인을 갖는 EDNMOS 소자의 더블 스냅백 현상 및 백그라운 도핑 농도 (BDC)의 영향을 조사하였다. 고전류 영역에서 낮은 BDC를 가진 EDNMOS 소자는 강한 스냅백으로 인해 취약한 ESD 성능과 높은 래치업 위험을 가지게 되나, 높은 BDC를 가진 EDNMOS 소자는 스냅백을 효과적으로 방지할 수 있음을 알 수 있었다. 따라서 BDC 제어로 안정적인 ESD 방지 성능과 래치업 면역을 구현할 수 있음을 밝혔다.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제53권3호
• /
• pp.166-172
• /
• 2004

Arc Fault Current is an electric discharge which is occurred in two opposite electrode. In this Paper, arc current control algorithm is designed for the interruption of arc fault current which is occurred in the low voltage network. This arc Is one of the main causes of electric fire. Arc fault in electrical network has the characteristics of low current, high impedance and high frequency. Conventional control algorithm does not have the arc current interrupt function. Hence, Control algorithm of arc current is designed for the interruption of arc fault current which has the modified arc characteristics.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1290-1292
• /
• 1995

A cylindrical-post magnetron sputtering system was designed for pipe inner coating. The discharge condition was depended on the gas pressure, magnetic field and pipe diameter. At given discharge current, discharge voltage increased a little with pipe diameter. The electron temperature and floating potential increased with magnetic field. The impact ion energy on the pipe increased with bias voltage. The TiN thin-film of $2{\mu}m$ thickness was formed by cylindrical-post magnetron sputtering system under the conditions of the pressure of 5mTorr, the applied voltage of 700V, the discharge current of 500mA, the magnetic field of 300G, and the bias voltage of -100V.