• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.8
• /
• pp.90-97
• /
• 2014

This paper presents a compensation method of unbalanced phase currents in interleaved bi-directional converters. Phase currents in interleaved bi-directional converter are apt to be unbalanced due to circuit parameter error and switch operation difference. This problem causes the switch element failure and the reduced efficiency of the converter. Therefore, it is necessary that a certain balance control algorithm is provided in interleaved bi-directional converter system. In this paper, a balance control algorithm based on the circular chain control method is proposed. Further, in order to reduce the number of phase current sensors, this paper shows a simple method in which phase currents can be extracted indirectly through a DC-link current sensor in both charging and discharging modes. The validity and the effectiveness of the proposed phase currents balance control algorithm are illustrated through the simulation results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.6
• /
• pp.539-547
• /
• 1992

Considering the field of high frequency or broad-band signal filtering with high speed, we pro-pose optical fiber filters which consist of directional couplers and optical fiber delay elements. Fiber delay line signal processor Is operated with Incoherent optical carrier because of Its simplicity. Due to the characteristics of the directional coupler which Is basic element of optical fiber filter a new design method which Is different from that of usual digital filter is required. By considering the characteristics of directional coupler and in order to make good use of the optical signal energy, we have given the design formulae and the conditions of optical fiber filters for the direct and the lattice form.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.4
• /
• pp.280-285
• /
• 2000

The conventional ultrasonic linear motors developed so far utilize a standing wave and are of a pi-type or a hybrid transducer type structure. Traveling wave type bi-direction linear motors have not been developed yet. This paper describes design of a new bi-directional ultrasonic linear motor working by means of a traveling wave. With the finite element method we design and verify validity of the new structure. And we determine its optimal structure size of design variables material and boundary conditions for proper generation of the traveling wave.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.2213-2215
• /
• 2000

In this paper we implemented a novel re-entrant mode microstrip directional coupler for realizing the high directivity characteristic using finite element (FE) analysis. In microstrip configuration, the high directivity can be reached by matching the even- and odd-mode effective phase velocities. Through the values of capacitance obtained from 2-dimensional finite element(FE) analysis, the phase velocities for each mode and the design parameter were extracted for the proposed coupled-line configuration. Based on the extracted design parameter with phase matching condition we designed and fabricated 30dB directional coupler at 850MHz. Experimental results show good performance with excellent isolation.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1993.04a
• /
• pp.151-157
• /
• 1993

In this paper a useful method on evaluating the joint stiffness of bolted memeber was introduced using optimization technique on the basis of Finite Element Method. A finite element model having one directional gap element at bo undary area was introduced to compensate the prying force in jointed members which might caused by geometrical configuration of members. Results showed a good aggrement with classical method in certain range and will be available to definine the design margine of pre-load design.

• Journal of the Korea Concrete Institute
• /
• v.19 no.5
• /
• pp.655-664
• /
• 2007

The inherent characteristic of concrete tensile cracks, directional nonlocal crack damage, causes so-called rotating tensile crack damage and softening of compressive strength. In the present study, a plasticity model was developed to describe the behavior of reinforced concrete planar members In tension-compression. To describe the effect of directional nonlocal crack damage, the concept of microplane model was combined with the plasticity model. Unlike existing models, in the proposed model, softening of compressive strength as well as the tensile crack damage were defined by the directional nonlocal crack damage. Once a tensile cracking occurs, the microplanes of concrete are affected by the nonlocal crack damage. In the microplanes, microscopic tension and compression failure surfaces are calculated. By integrating the microscopic failure surfaces, the macroscopic failure surface is calculated. The proposed model was implemented to finite element analysis, and it was verified by comparisons with the results of existing shear panel tests.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.4
• /
• pp.386-392
• /
• 2002

This paper presents a basic characteristics of 4-element circular array dipole antennas for 4-sector beam steering. The coupled integral equations for the unknown current distributions on dipole elements are derived and solved by applying Galerkin's method of moments. The parasitic elements have been used to increase the directional gain and the beam is steered electronically either by sswitching between the parasitic elements or switching the position of the active element. The parasitic elements are switched short-circuited or open-circuited as required to steer a directional beam. In order to verify the theoretical analysis, the radiation pattern was compared with experiments.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.10
• /
• pp.1097-1106
• /
• 2009

In this paper, the cross monopole antenna with branch element is presented and its radiation characteristics are investigated. To confirm the broadband characteristics of the proposed antenna, the experimental antenna is designed, fabricated, and its radiation characteristics are measured in PCS, WCDMA, WiBro and S-DMB band(1.750~2.655 GHz). It is shown that the designed antenna has the non-directional pattern in the horizontal plane, the directional pattern in the vertical plane, VSWR less than 1.5 and gain over 1.9 dBi in 1.72~2.82 GHz. From these results, the presented antenna is conformed as a broadband antenna which can be used for PCS, WCDMA, WiBro and S-DMB band.

• Transactions of Materials Processing
• /
• v.11 no.3
• /
• pp.231-237
• /
• 2002

The manufacturing of a metal bellows consists of the four main forming processes; deep-drawing, ironing, tube bulging and folding. Among these, the bulging and folding processes are critically important because the quality of metal bellows is greatly influenced by the forming conditions of these processes. In the present study, the finite element analysis technique is applied to the bulging and folding processes. The springback analysis is also called out. From the analysis results, it has been revealed that around the crown point the stress state is in one-directional tension and one-directional bending mode. Meanwhile, around the inner point of metal bellows it is in two-directional bending mode. It has also revealed that the thickness of metal bellows around the crown point is nearly uniform.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.4
• /
• pp.174-182
• /
• 2003

Recently, medical imaging has taken interest on CAD based solution for anatomical part fabrication or finite element analysis of human body. In principle, contours representing object boundary are obtained through image processing techniques. Surface models are then approximated by a skinning method. For this, various methods should be applied to medical images and contours. The major bottleneck of the reconstruction is to remove shape inconsistency between contours and to generate the branching surface. In order to solve these problems, bi-directional smoothing and the composite contour generation method are proposed. Bi-directional smoothing has advantage of removing the shape inconsistency between contours and minimizing shrinkage effect with a large number of iterations. The composite contour by the proposed method ensures smooth transition in branching region.