• Journal of KSNVE
• /
• v.9 no.2
• /
• pp.317-323
• /
• 1999

Dynamic characteristics of catenary that supplies electrical power to high-speed trains are investigated. A simple catenary is composed of the contact and messenger wires connected by droppers possessing bi-directional stiffness properties. For slender, repeating structures such as catenary, both the wave propagation and vibration properties need to be understood. The influence of parameters that determine catenary dynamics are investiaged through numerical simulations involving finite element models. The effects of the tension and flexural rigidity of the contact wire is first investigated. The effects of dropper characteristics are then investigated. For linear droppers wave propagation as well as modal properties are determined. For large catenary motion, droppers can be modeled as bi-directional elements possessing low stiffness in compression and high stiffness in tension. For this case, impulse response is computed and compared with the cases of linear droppers. It is found that the catenary dynamics are primarily determined by contact wire tension and dropper properties, with large responses observed in 5∼40 Hz frequency range. In particular, the dropper stiffness and spacing are found to have dominant influence on the response frequency and the wave transmission characteristics.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.5
• /
• pp.519-526
• /
• 2021

In this paper, an array antenna for LOS datalink for mounting UAV(Unmanned Aerial Vehicle) of low-probability of intercept is presented. For low RCS, radome was designed by conformal form, and other components were inserted into the UAV. The antenna of the transmitter and receiver are each composed of 12×12 array antennas, and include a beam steering function by controlling the phase of the unit element for the Uni-directional pattern and the Bi-directional pattern. As a result of the measurement of the manufactured antenna, it was confirmed that all the required specifications were met, and the installing possibility of the UAV platform on low-probability of intercept in the future was confirmed.

• Earthquakes and Structures
• /
• v.19 no.6
• /
• pp.427-444
• /
• 2020

The performance of an isolated horizontally curved continuous bridge with High Damping Rubber (HDR) Bearings has been investigated under seismic loading conditions. The effectiveness of response controls of the bridge by HDR bearings for various aspects viz. variation in ground motion characteristics, multi-directional effect, level of earthquake shaking, varying incidence angle, have been determined. Three recorded ground motions, representative of historical earthquakes along with near-field, far-field and forward directivity effects, have been considered in the study. The efficacy of the bearings with bidirectional effect considering interaction behavior of bearing and pier has also been investigated. Modeling and analysis of the bridge have been done by finite element approach. Sensitivity studies of the bridge response with respect to design parameters of the bearings for the considered ground motions have been performed. The importance of the nonlinearity of HDR bearings along with crucial design parameters has been identified. It has been observed that the HDR bearings performed well in different variations of ground motions, especially for controlling torsional moment. However, the deck displacement has been found to be increased significantly in case of Turkey ground motions, considering forward directivity effect, which needs to be paid more attention from designer point of view.

• Steel and Composite Structures
• /
• v.47 no.5
• /
• pp.569-585
• /
• 2023

This paper proposes an efficient approach for the structural topology optimization of bi-directional functionally graded structures by incorporating popular radial basis functions (RBFs) into an implicit level set (ILS) method. Compared to traditional element density-based methods, a level set (LS) description of material boundaries produces a smoother boundary description of the design. The paper develops RBF implicit modeling with multiquadric (MQ) splines, thin-plate spline (TPS), exponential spline (ES), and Gaussians (GS) to define the ILS function with high accuracy and smoothness. The optimization problem is formulated by considering RBF-based nodal densities as design variables and minimizing the compliance objective function. A LS-RBF optimization method is proposed to transform a Hamilton-Jacobi partial differential equation (PDE) into a system of coupled non-linear ordinary differential equations (ODEs) over the entire design domain using a collocation formulation of the method of lines design variables. The paper presents detailed mathematical expressions for BiDFG beams topology optimization with two different material models: continuum functionally graded (CFG) and mechanical functionally graded (MFG). Several numerical examples are presented to verify the method's efficiency, reliability, and success in accuracy, convergence speed, and insensitivity to initial designs in the topology optimization of two-dimensional (2D) structures. Overall, the paper presents a novel and efficient approach to topology optimization that can handle bi-directional functionally graded structures with complex geometries.

• Geomechanics and Engineering
• /
• v.35 no.4
• /
• pp.367-383
• /
• 2023

The present paper examines the natural frequency responses of the bi-directional (n_x-n_y, n_y-n_z and n_z-n_x) and multidirectional (n_x-n_y-n_z) functionally graded (FG) plate and curved structures with and without porosity. The even and uneven kind of porosity pattern are considered to observe the influence of porosity type and porosity index. The numerical findings have been obtained using a higher order shear deformation theory (HSDT) based isometric finite element (FE) approach generated in a MATLAB platform. According to the convergence and validation investigation, the proposed HSDT based FE model is adequate to predict free vibrational responses of multidirectional porous FG plates and curved structures. Further a parametric analysis is carried out by taking various design parameters into account. The free vibrational behavior of bidirectional (2D) and multidirectional (3D) perfect-imperfect FGM structure is examined against various power law index, support conditions, aspect, and thickness ratio, and for the curvature of curved structures. The results indicate that the maximum non-dimensional fundamental frequency (NFF) value is observed in perfect FGM plates and curved structures compared to porous FGM plates and curved structures and it is maximum for FGM plates and curved structures with uneven kind of porosity than even porosity.

• Composites Research
• /
• v.15 no.2
• /
• pp.1-10
• /
• 2002

The strength of glass/epoxy fabric joints under pin-loading is estimated based on the characteristics length method and experiment. To investigate the effect of finite element idealization for the contact between pin and laminate, three modeling cases are analyzed; assuming the cosine load distribution around the contact area, constraining the radial displacement at the hole boundary, and using the contact element. To study the effect of failure criteria, Tsai-Wu and Yamada-Sun methods are applied on the characteristic curve. The results of the nonlinear analysis using the contact element showed good agrements with experimental data in both laminates made of uni-directional prepreg tapes and fabrics. In terms of failure criteria, Tsai-Wu method showed better agreement with experimental results than the one by Yamada-Sun laminate.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.466-471
• /
• 2008

Structural vibration and noise are hot issues in underwater vehicles such as submarines for their survivability. Therefore, active vibration and noise control of submarine, which can be modeled as hull structure, have been conducted by the use of piezoelectric materials. Traditional piezoelectric materials are too brittle and not suitable to curved geometry such as hull structures. Therefore, advanced anisotropic piezoceramic actuator named as Macro-Fiber Composite (MFC), which can provide great flexibility, large induced strain and directional actuating force is adopted for this research. In this study, dynamic model of the smart hull structure is established and active vibration control performance of the smart hull structure is evaluated using optimally placed MFC. Actuating performance of MFC is evaluated by finite element analysis and dynamic modeling of the smart hull structure is derived by finite element method considering underwater condition. In order to suppress the vibration of hull structure, Linear-Quadratic-Gaussian (LQG) algorithm is adopted. After then active vibration control performance of the proposed smart hull structure is evaluated with computer simulation and experimental investigation in underwater. Structural vibration of the hull structure is decreased effectively by applying proper control voltages to the MFC actuators.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.22 no.3
• /
• pp.199-209
• /
• 2009

This paper deals with the three-dimensional finite element analysis of failure behavior of UHPFRC I-beam under monotonic load. Different from the constitutive law of normal and high strength concrete, an elastic-plastic fracture model that considers the tensile strain hardening is proposed to describe the material properties of UHPFRC. A multi-directional fixed crack criterion with tensile strain hardening is defined in the tensile region, and Drucker-Prager criterion with an associated flow rule is adopted in the compressive region. The influence of span, prestressing force and section on the behavior of UHPFRC I-beam are investigated. The comparison of the numerical results with the test results indicates a good agreement.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.2
• /
• pp.138-145
• /
• 2009

Structural vibration and noise are hot issues in underwater vehicles such as submarines for their survivability. Therefore, active vibration and noise control of submarine, which can be modeled as hull structure, have been conducted by the use of piezoelectric materials. Traditional piezoelectric materials are too brittle and not suitable to curved geometry such as hull structures. Therefore, advanced anisotropic piezocomposite actuator named as Macro-Fiber Composite(MFC), which can provide great flexibility, large induced strain and directional actuating force is adopted for this research. In this study, dynamic model of the smart hull structure is established and active vibration control performance of the smart hull structure is evaluated using optimally placed MFC. Actuating performance of MFC is evaluated by finite element analysis and dynamic modeling of the smart hull structure is derived by finite element method considering underwater condition. In order to suppress the vibration of hull structure, Linear Quadratic Gaussian(LQG) algorithm is adopted. After then active vibration control performance of the proposed smart hull structure is evaluated with computer simulation and experimental investigation in underwater. Structural vibration of the hull structure is decreased effectively by applying proper control voltages to the MFC actuators.

• Journal of Advanced Navigation Technology
• /
• v.19 no.1
• /
• pp.60-65
• /
• 2015

In the present study, compact $0^{th}$ order resonant antenna for 2.4 GHz ISM frequency band is newly proposed. In case of wireless communication systems such as wi-fi, bluetooth and Zigbee, antennas with omni-directional radiation pattern are necessary because of the demands for uniformly received electric field strength without variation for direction. It is well-known that $0^{th}$ order resonant antennas are not only advantageous for miniaturization but also have advantage of maintaining omni-directional radiation pattern. The proposed antenna is composed of two-element array in which the size of unit element should be smaller than ${\lambda}/4$ correspondent to the resonant length of typical monopole antennas The proposed antenna which is placed at middle and upper side of PCB with $50{\times}50mm^2$ size is designed and fabricated within limited space of $8{\times}5mm^2$. The measured impedance bandwidth ($S_{11}{\leq}-10dB$) is about 100 MHz (2.4~2.5 GHz) which corresponds to quite wide bandwidth in comparison with the antenna size, and also the measured peak gain over the passband is more than 3 dBi which is thought to be slightly wider than the other $0^{th}$ order resonant antenna.