• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2929-2934
• /
• 2007

Prediction methods for cavitation noise are presented. At first, direct numerical simulation of cavitating flow noise has been performed, and acoustic analogy equation based on the cavitation noise modeling is derived. For the direct numerical simulation, a density based homogenous equilibrium model is employed to simulate cavitating two-phase flow and the governing equations are solved with high-order numerical schemes to resolve cavitation noise. The compressible Navier-Stokes equations for mixture fluids are discretized with a sixth-order central compact scheme, and the steep gradient of flow variables and supersonic regions are treated with the selective spatial filtering technique. The direct simulation of cavitating flow noise is performed for a 2D circular cylinder at cavitation number 0.7 and 1. The far-field noise is also predicted with the derived analogy equation. Noise spectrum predicted with the equation is well compared with the result of direct numerical simulation and also agree well with the theory.

• 한국방송∙미디어공학회:학술대회논문집
• /
• 한국방송공학회 2002년도 정기총회 및 학술대회
• /
• pp.9-14
• /
• 2002

Direct-conversion receiver(DCR) architecture has superior advantages in size, cost, and power over superheterodyne receiver architectures. However, the use of direct-conversion receiver architecture has been limited due to the direct-current offset noise. The ac coupling, which is used to overcome the direct-current offset noise, causes an inter-symbol interference(ISI), whose effects can be effectively mitigated using an equalizer. In this paper, the performance of a direct-conversion receiver with ac coupling in the presence of direct-current offset is analyzed via computer simulation. The simulation result shows that by using decision feedback equalizer with LMS(Least Mean Square) algorithm, signal-to-noise ratio loss of the direct-conversion receiver compared to the idea receiver can be reduced to less than 1㏈ for corner frequencies as large as 10% of the symbol rate.

• Journal of Biosystems Engineering
• /
• 제31권4호
• /
• pp.323-333
• /
• 2006

Introduction of a direct engine-PTO driveline to agricultural tractors has reduced production cost and increased transmission efficiency of the PTO driveline. However, this type of PTO driveline has caused a severe rattle noise in the PTO gearbox under idle conditions. This study was conducted to investigate the causes of the rattle noise and the effects of driveline parameters on it. A mathematical model was developed for a direct engine-PTO driveline. The model was proved experimentally to be accurate enough to simulate the dynamic characteristics of the PTO driveline motions. The simulation study showed that the rattle noise was caused by collisions between the driving and driven gears in the PTO gearbox due to velocity variation of the gears, which was induced by torque fluctuations from the engine. It was also found that the rattle noise decreased with the drag torque and mass moment of inertia of the engine flywheel. Smaller mass moment of inertia of the driven gears and backlash also reduced the rattle noise. However, increasing the drag torque and mass moment of the engine flywheel or decreasing the backlash and mass moment of inertia of the driven gears were limited practically by their detrimental effects on transmission efficiency, gear strength and smooth meshing of the gears.

• 대한전자공학회논문지
• /
• 제21권6호
• /
• pp.105-114
• /
• 1984

본 논문에서는 direct sequence(DS) 방식을 이용한 spread spectrum system에 사용할 수 있는 빠른 초기 동기 방법을 제안하였다. 수식적인 모델을 세우고 해석을 한 후 computer simulation을 거쳐 제안된 system의 성능을 분석하여 sliding correlator에 비해 우수함을 입증하였다. 입력 신호의 signal-to-noise ratio(SNR)가 -18dB에서 초기 동기 시간이 45ms 소요되었다. 이 방법의 hardsware 구현과 실험 결과도 설명하였다.

• Journal of Biosystems Engineering
• /
• 제32권3호
• /
• pp.137-144
• /
• 2007

An anti-backlash gear was developed to reduce the rattle noise generated from the gearbox of a direct-engine PTO driveline of agricultural tractors under idling. A pair of gears using the anti-backlash gear as driven part was modeled and verified. Using the verified model, a computer simulation was conducted to investigate the effects of design parameters of the anti-backlash gear on the reduction of rattle noise. The optimum values of the design parameters were also determined by the computer simulation. The optimized anti-backlash gear was then manufactured and installed on the experimental PTO driveline for the performance test. Measurement of rattle noise was made to evaluate its performance before and after the driven gear of the PTO gearbox was replaced by the optimized anti-backlash gear. Results of the study were as follows: The optimum values of the design parameters, spring constant and deformation, may be determined by a relationship: $$k{\ge}\frac{4364.7}{150{\delta}-23.564}$$ The optimized anti-backlash gear reduced the rattle noise maximally by 16.9 dBA. This concluded that it would be most effective to use the optimized anti-backlash gear to eliminate the rattle noise in the PTO driveline.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.2060-2065
• /
• 2003

Aeolian tone generation from a two dimensional circular cylinder is numerically investigated via direct numerical simulation and hydrodynamic-acoustic splitting method. All governing equation are spatially discretized with the sixth-order compact scheme and fourth-order Runge-Kutta method to avoid excessive numerical dissipations and dispersions of acoustic quantities. Comparisons of two results show that the previous splitting method can not accurately predict the aeroacoustic noise of wall bounded shear flow. In this study, a perturbation viscous term and a new energy equation have been developed. This modified splitting method accurately predicts aeroacoustic noise from wall-bounded shear flow. The present results agree very well with the direct numerical simulation solution.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 추계종합학술대회 논문집(2)
• /
• pp.309-312
• /
• 2000

In this paper, The Influence of chromatic fiber dispersion on the transmission distance of MMW(millimeter-wave) link is analyzed and discussed. It is shown that dispersion significantly limits the transmission distance in intensity modulated direct detection and heterodyne links operating in the above 20㎓ frequency region by inducing a carrier to noise penalty on the transmitted signal. We analyze and discuss the influence of dispersion induced CNR(Carrier to Noise Ratio) penalty for direct detection and heterodyne method from simulation.

• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2005년도 하계학술대회
• /
• pp.443-447
• /
• 2005

In this paper, a low noise amplifier(LNA) in a receiver of a Low Noise Block Down Converter (LNB) for direct broadcasting service(DBS) is implemented using GaAs HEMT. The 2-stage LNA is designed for the bandwidth of 11.7GHz - 12.2GHz. The result of a simulation of the LNA using Advanced Design System(ADS) shows that the noise figure is less than 1.4dB, the gain is greater than 23dB and the flatness is 1dB in the bandwidth of 11.7 to 12.2GHz.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.439-444
• /
• 2001

We provide methods to simulate noise propagation for an outdoor environment. Forward tracing method traces sound vectors from sources to receivers while geometry based computation finds all possible sound propagation between sources and receivers geometrically. We discuss defects in relying on a forward tracing method, and suggest a geometry based method. Geometry based method considers all possible direct and indirect(propagation via limited number of reflections) sound propagation saving computational time compared to forward sound tracing. Our simulation results are visualized using VRML(Virtual Reality Modeling Language).

• Journal of Communications and Networks
• /
• 제14권5호
• /
• pp.540-545
• /
• 2012

In this paper, the lagged cross-correlation of two probability density functions constructed by kernel density estimation is proposed, and by maximizing the proposed function, adaptive filtering algorithms for supervised and unsupervised training are also introduced. From the results of simulation for blind equalization applications in multipath channels with impulsive and slowly varying direct current (DC) bias noise, it is observed that Gaussian kernel of the proposed algorithm cuts out the large errors due to impulsive noise, and the output affected by the DC bias noise can be effectively controlled by the lag ${\tau}$ intrinsically embedded in the proposed function.