• 대한기계학회논문집B
• /
• 제28권7호
• /
• pp.763-770
• /
• 2004

The problem of edge overcoating developed near the edge of the steel strip is studied quantitatively in the gas wiping process of continuous hot-dip galvanizing. It has been assumed that the edge overcoating occurs due to the reduced impact pressure of wiping gas on the strip edge and it is one of detrimental problems to the quality of coating products. In order to analyse the edge overcoating problem numerically, three-dimensional unsteady flows due to the gas wiping are calculated by using a commercial code, STAR-CD. Standard $\kappa$-$\varepsilon$ model is used as a turbulence model. The 1D code for calculation of coating thickness is constructed by using continuity and Navier-Stokes equations. The calculation results have shown good agreement with measurements of edge overcoating thickness, taken from galvanizing line trials. Therefore it is conformed that the major cause of edge overcoating is the reduced impact pressure of wiping gas on the strip surface.

• 한국분말재료학회지
• /
• 제21권1호
• /
• pp.21-27
• /
• 2014

In this study, diatomite based materials were investigated as a support filter for silica particle coating. The silica sol for coating was synthesized by a st$\ddot{o}$ber process. The diatomite support was dry-pressed at 10 MPa and sintered at $1200^{\circ}C$ for 1 hour. The coating sol was prepared as a mixture of EtOH and silica sol. The diatomite support was coated by a dip-coating process. Silica coated diatomite filter was sintered at $1000{\sim}1200^{\circ}C$ for 1 hour. The largest pore size was decreased with increasing concentration ratio of coating sol. The gas and water permeability of silica coated diatomite decreased with increasing of concentration ratio of the coating sol.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.233-233
• /
• 2006

[ $Y_{2}O_{2}S:Eu$ ], a red phosphor, coated with silica nanoparticles or nanocomposites composed of silica nanoparticles and polymeric materials such as PMMA and PVP was prepared via sol-gel process. Samples were prepared from four different methods coded P1, P2, P3, and P4. P1 includes a conventional sol-gel process and a dip-coating method while P2 has the same procedure with P1 except that nanocomposites containing both silica nanoparticles and polymer prepared by sol-gel process were used as coating materials. In P3 method, phosphors were dispersed in a solution containing silica precursor, i.e., TEOS and then polymerization was performed to coat onto the phosphors surface while P4 followed the same procedure with P3 except that a solution containing both TEOS and organic monomer were used in preparing coating materials. Among various coating methods examined in this study, uniform coating of phosphor could be achieved by using method P4, i.e., phosphor surface coating in a solution containing hydrophobic monomer and TEOS. Furthermore, $Y_{2}O_{2}S:Eu$ red phosphor coated with nanocomposite composed of PMMA matrix and silica nanoparticles exhibited enhanced PL intensity and long-term stability.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.1386-1388
• /
• 2009

We report on a new method of fabricating color filters based on selective wetting of color inks. The reversible formation of a hydrophobic layer provides sequential generation and protection of successive color filter patterns through a simple coating process. The transmittance and geometrical properties of the fabricated color filter were described.

• Corrosion Science and Technology
• /
• 제11권1호
• /
• pp.15-19
• /
• 2012

Both electrogalvanized and hot-dip galvanized steel sheets have been finally produced via organic-inorganic surface coating process on the zinc surface to enhance corrosion resistance and afford additional functional properties. Recently, POSCO has been developed a variety of chromate-free coated steels that are widely used in household, construction and automotive applications. New organic-inorganic hybrid coating solutions as chromate alternatives are comprised of surface modified silicate with silane coupling agent and inorganic corrosion inhibitors as an aqueous formulation. In this paper we have prepared new type of hybrid coatings and evaluated quality performances such as corrosion resistance, spot weldability, thermal tolerance, and paint adhesion property etc. The electrogalvanized steels with these coating solutions exhibit good anti-corrosion property compared to those of chromate coated steels. Detailed components composition of coating solutions and experimental results suggest that strong binding between organic-inorganic hybrid coating layer and zinc surface plays a key role in the advanced quality performances.

• 한국세라믹학회지
• /
• 제33권7호
• /
• pp.839-847
• /
• 1996

• Corrosion Science and Technology
• /
• 제9권3호
• /
• pp.105-108
• /
• 2010

The product specification of the Continuous Hot Dip Galvanizing Line (CGL) changes and varies constantly with different customers' requirements, especially in the zinc coating weight which is from 30 to 150 g/$m^2$ on each side. Since the coating weight of zinc changes often, it is very important to reduce time spent in the transfer of target values changed for low production cost and yield loss. The No.2 CGL in China Steel Corporation (CSC) has improved the control of the air knife which is designed by Siemens VAI. CSC proposed an experiment design which is an $L_9(3^4)$ orthogonal array to find the relations between zinc coating weight and the process parameters, such as the line speed, air pressure, gap of air knife and air knife position. A non-linear regression formula was derived from the experimental results and applied in the mathematical model. A new air knife feedforward control system, which is coupled with the regression formula, the air knife control system and the process computer, is implemented into the line. The practical plant operation results have been presented to show the transfer time is obviously shortened while zinc coating weight target changing and the product rejected ratio caused by zinc coating weight out of specification is significantly reduced from 0.5% to 0.15 %.

• Corrosion Science and Technology
• /
• 제11권1호
• /
• pp.1-8
• /
• 2012

The development of martensitic grades which can be processed in continuous galvanizing lines requires the reduction of the oxides formed on the steel during the hot dip process. This reduction mechanism was investigated in detail by means of High Resolution Transmission Electron Microscopy (HR-TEM) of cross-sectional samples. Annealing of a martensitic steel in a 10% $H_2+N_2$ atmosphere with the dew point of $-35^{\circ}C$ resulted in the formation of a thin $_{C-X}MnO.SiO_{2}$ (x>1) oxide film and amorphous $_{a-X}MnO.SiO_{2}$ oxide particles on the surface. During the hot dip galvanizing in Zn-0.13%Al, the thin $_{C-X}MnO.SiO_{2}$ (x>1) oxide film was reduced by the Al. The $_{a-X}MnO.SiO_{2}$ (x<0.9) and $a-SiO_{2}$ oxides however remained embedded in the Zn coating close to the steel/coating interface. No $Fe_{2}Al_{5-X}Zn_{X}$ inhibition layer formation was observed. During hot dip galvanizing in Zn-0.20%Al, the $_{C-X}MnO.SiO_{2}$ (x>1) oxide film was also reduced and the amorphous $_{a-X}MnO.SiO_{2}$ and $a-SiO_{2}$ particles were embedded in the $Fe_{2}Al_{5-X}Zn_{X}$ inhibition layer formed at the steel/coating interface during hot dipping. The results clearly show that Al in the liquid Zn bath can reduce the crystalline $_{C-X}MnO.SiO_{2}$ (x>1) oxides but not the amorphous $_{a-X}MnO.SiO_{2}$ (x<0.9) and $a-SiO_{2}$ oxides. These oxides remain embedded in the Zn layer or in the inhibition layer, making it possible to apply a Zn or Zn-alloy coating on martensitic steel by hot dipping. The hot dipping process was also found to deteriorate the mechanical properties, independently of the Zn bath composition.

• Korean Chemical Engineering Research
• /
• 제57권4호
• /
• pp.525-530
• /
• 2019

고체산화물 연료전지의 성능과 안정성은 전극의 기공률, 기공 분포와 전해질의 치밀도, 두께에 따라 결정 된다. 연료극의 기공률과 기공 분포는 활성면적와 연료 흐름에 영향을 주고, 전해질의 치밀한 미세구조와 두께는 단위전지의 Ohmic 저항에 영향을 준다. 하지만 이를 위해 값 비싼 공정 장비를 이용하거나 여러 단계의 제작 공정이 추가 될 경우 단위전지 제작비가 증가하므로 상업화를 목표로 하는 연구에는 적합하지 않다. 본 연구에서는 위와 같은 문제점들을 해결하기 위하여 상용 소재 기반의 NiO-YSZ 연료극을 선정 후 간단한 혼합 방법 및 일축가압 성형법과 담금코팅(dip coating) 공정을 사용하여 저비용 고효율의 세라믹 공정 기반의 고성능 단위전지를 제작하였다. 연료극의 기공률은 기공형성제로서 사용되는 카본 블랙(CB, carbon black)의 첨가량(10~20 wt%)과 최종 소결온도($1350{\sim}1450^{\circ}C$)를 변경하며 제어하였고, YSZ 전해질의 두께와 미세구조는 담금코팅 슬러리의 고상 분말량(YSZ, 1~5 vol%)을 제어하여 치밀한 박막의 전해질을 구현하고자 하였다. 그 결과 Ni-YSZ 연료극에서 최적의 값으로 잘 알려진 40%의 기공률은 카본 블랙을 15 wt% 첨가하고최종소결온도를 $1350^{\circ}C$로설정함으로써얻을수있었다. 담금코팅을통한 YSZ 두께는 $2{\sim}28{\mu}m$까지 제어가 가능하였고, 3 vol%의 고상분말량에서 치밀한 전해질 미세구조가 형성되었다. 최종적으로 40%의 기공률을 갖는 Ni-YSZ 연료극, $20{\mu}m$ 두께의 치밀한 YSZ전해질, LSM-YSZ 공기극으로 구성된 단위전지는 $800^{\circ}C$에서 $1.426Wcm^{-2}$의 우수한 성능을 얻을 수 있었다.

• 한국세라믹학회지
• /
• 제33권11호
• /
• pp.1195-1202
• /
• 1996

To prepare the dielectric thin films of (Pb1-xSrx)TiO3 (x=0.1, 0.2, 0.3, 0.35, 0.5) by the sol-gel process titanium (IV) isopropoxide (Ti[OCH(CH3)2]4) and Pb Sr, acetate were used therefore the thin films were fabricated by dip-coating method. Stability of the sol decreased with addition of Sr content thin films could be fabricated up to 35mol% Over this range precipitation of sol occured thin films couldn't be obtained. Transmittance of thin films at visible range decreased with the increase of heat-treatment temperature but exhibited transmit-tance above 60% in all case. Moreover transmittance of thin films at visible range slightly increased with of addition of Sr,. When thin film containing 30 mol% srontium was heated at 600℃ the best perovskite phase was obtained. The dielectric constant (ε) was 280 and dielectric loss factor (tan δ) was 0.021 and curie tempera-ture (Tc) decreased with the increase of addition of Sr.