• Steel and Composite Structures
• /
• 제3권3호
• /
• pp.185-198
• /
• 2003

The concept of performance based seismic design has been gradually accepted by the earthquake engineering profession recently, in which the cost-effectiveness criterion is one of the most important principles and more attention is paid to the structural performance at the inelastic stage. Since there are many uncertainties in seismic design, reliability analysis is a major task in performance based seismic design. However, structural reliability analysis may be very costly and time consuming because the limit state function is usually a highly nonlinear implicit function with respect to the basic design variables, especially for the complex large-scale structures for dynamic and nonlinear analysis. Understanding statistical properties of the structural inelastic deformation, which is the aim of the present paper, is helpful to develop an efficient approximate approach of reliability analysis. The present paper studies the statistical properties of the maximum elastoplastic story drift of steel frames subjected to earthquake load. The randomness of earthquake load, dead load, live load, steel elastic modulus, yield strength and structural member dimensions are considered. Possible probability distributions for the maximum story are evaluated using K-S test. The results show that the choice of the probability distribution for the maximum elastoplastic story drift of steel frames is related to the mean value of the maximum elastoplastic story drift. When the mean drift is small (less than 0.3%), an extreme value type I distribution is the best choice. However, for large drifts (more than 0.35%), an extreme value type II distribution is best.

• 한국재난관리표준학회지
• /
• 제4권1호
• /
• pp.49-55
• /
• 2011

본 연구는 철근 콘크리트 구조물의 새로운 자동화 최적설계 알고리즘을 제시하였다. 기존의 주철근과 콘크리트 단면사이즈 등의 국한된 최적설계 범위를 벗어나 철근의 부착길이, 매입길이, 콘크리트 커버두께 등 세부설계사항까지 모두 고려한 실무에 적합한 효용성 높은 설계알고리즘을 제시함으로써 앞으로 실무분야에 많은 기여를 할 수 있다고 보여 진다.

• 대한조선학회논문집
• /
• 제56권3호
• /
• pp.187-199
• /
• 2019

In the case of gas carriers and oil tankers, pipes are installed on the upper deck as a moving passage to load LPG, LNG, crude oil, etc. Pipes used for loading or unloading liquid cargo in cargo holds are connected to the hull through support structures. However, many cases of hull damage have been reported where the various equipment and support structures are installed on the upper deck. It is assumed that not only the structural discontinuity where the hull and the pipe support structure meet, but also action due to the pipe loads and the hull girder bending moment are simultaneously affected. This paper deals with the design and strength evaluation of the support structure of pipes and cables installed on the upper deck of commercial ships and offshore structures. For these supporting structures, design conditions and working loads were defined. The design procedure was established through the structure analysis on the method of determining the member dimensions. A series of finite element analysis was performed on the factors to be considered in the design and the effects were discussed. The accuracy and design periods of the strength evaluation was improved and reduced by application of the automation program in the finite element analysis. It is also expected that the design reliability of the shipyard is improved.

• 국제학술발표논문집
• /
• The 7th International Conference on Construction Engineering and Project Management Summit Forum on Sustainable Construction and Management
• /
• pp.159-166
• /
• 2017

Recently, the wooden structure has been revived again as an eco-friendly structure technique. It is the counterattack of the wood material, which has become more recognized as a finishing material pushed by the concrete material in the rapid growth after the Industrial Revolution. However, it is difficult to conclude that this is a tendency of the construction market in the whole country. Perhaps this is a tendency to appear more strongly in Korea. It could be seen by comparing the characteristics of the overseas construction market with Korean's and the advanced constructed case of large-scale wooden structures in overseas. National wooden buildings show own characteristics such as construction methods, materials, and member dimensions of wood structures by country, which could be seen as a result of continuously developing their own technology. However, in Korea, despite its unique wooden structure and technology (Hanok; Korean traditional housing), it has not been developed continuously and treated it only as a living building exhibit. This is evidenced by the fact that only one percent of the building is constructed with traditional wooden building technology. Therefore, there are various efforts to modernize the traditional wooden structure technology, but it still does not reach the level of advanced wooden technology abroad. The characteristics of the Korean wooden building market were analyzed in order to suggest ways to develop the Korean wood structure technology. The characteristics of Hanok construction were analyzed through quantitative criteria to define the main development tasks for Hanok development to propose the long-term development path.

• 한국광물학회지
• /
• 제10권2호
• /
• pp.105-113
• /
• 1997

Mineral description and mineralogical characterization were made for the wellsite, a barrian zeolite, which found as diagenetic alterations in the Miocene pyroclastic rocks in Gampo area. The wellsite occurs together with clinoptilolite, smectite and apatite as euhedral crystallites (0.2~0.4mm) forming interpenetraion twinning in the vesicles of altered pmice fragments. Compared to other reported wellsites, the wellsite is rather silicic (Si/(Al+Fe): 3.12-3.16) and Ca-rich. Unit cell dimensions and chemical formular determined from XRD, EMPA and TGA data are as follows:a=9.883$\AA$, b=14.204$\AA$, c=8.677$\AA$, $\beta$-124.764$^{\circ}$, (Ba0.57K0.36)(Ca1.18Na0.04)Al3.9Si12.1O32.13.9H2O.The cation composition of the Gampo wellsite, which shows an exchange reaction in the form of Ba2++Ca2+=2(K++Na-), is deviated far from the compositional range of a phillipsite-harmotome series. Due to higher abundance of divalent cations (Ca, Ba) and si in the wellsite, cimpared to those of the phillipsite and harmotome reported in other areas, the zeolite seems to be characteristic of higher water content (18.7 wt%) and higher thermal stability. XRD, chemical and thermo-chemical results of the wellsite reflects that wellsite is rather a Ba- and Ca-rich end member of a phillipsite-harmotome-wellsite series than an intermediate phase of phillipsite-harmotome series or a barrian variety of phillipste.

• Earthquakes and Structures
• /
• 제23권1호
• /
• pp.13-21
• /
• 2022

Masonry constructions exhibit uncertain behaviors under dynamic effects such as seismic action. Complex issues arise in the idealization of structural systems of buildings having different material types and mechanical properties. In this study, the structural behavior of a vaulted masonry building constructed using full clay brick and lime-based mortar and sitting on consecutive arches was investigated by experimental and numerical approaches. The dimensions of the structure built in the laboratory were 391 × 196 cm, and its height was 234 cm. An incremental repetitive loading was applied to the prototype construction model. Along the gradually increasing loading pattern, the load-displacement curves of the masonry structure were obtained with the assistance of eight linear displacement transducers. In addition, crack formation areas, and relevant causes of its formation were determined. The experimental model was idealized using the finite element method, and numerical analyses were performed for the area considered as linear being under similar loading effect. From the linear analyses, the displacement values and stress distribution of the numerical model were obtained. In addition, the effects of tie members, frequently being used in the supports of curved load-bearing elements, on the structural behavior were examined. Consequently, the experimental and numerical analysis results were comparatively evaluated.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2001년도 봄 학술발표회 논문집
• /
• pp.102-109
• /
• 2001

In order to take account of the statistical properties of probability variables used in the structural analysis, the conventional approach using the safety factor based on past experience usually estimated the safety of a structure. The real structures could only be analyzed with the error in estimation of loads, material characters and the dimensions of the members. But the errors should be considered systematically in the structural analysis. Structural safety could not precisely be appraised by the traditional structural design concept. Recently, new approach based on the probability concept has been applied to the assessment of structural safety using the reliability concept. Thus, the computer program by the Probabilistic FEM is developed by incorporating the probabilistic concept into the conventional FEM method. This paper estimated for the reliability of a plane stress structure by Advanced First-Order Second Moment method using von Mises, Tresca and Mohr-Coulomb failure criterions. The reliability index and failure probability of attained by the Monte Carlo Simulation method with the von Mises criterion were same as PFEM, but the Monte Carlo Simulation were very time-consuming. The variance of member thickness and load could influence the reliability and failure probability most sensitively among the design variables from the results of the parameter analysis. And proper failure criterion must be used to design safely.

• Steel and Composite Structures
• /
• 제1권2호
• /
• pp.171-185
• /
• 2001

The design of tall buildings has recently provided many challenges to structural engineers. One such challenge is to minimise the cross-sectional dimensions of columns to ensure greater floor space in a building is attainable. This has both an economic and aesthetics benefit in buildings, which require structural engineering solutions. The use of high strength steel in tall buildings has the ability to achieve these benefits as the material provides a higher strength to cross-section ratio. However as the strength of the steel is increased the buckling characteristics become more dominant with slenderness limits for both local and global buckling becoming more significant. To arrest the problems associated with buckling of high strength steel, concrete filling and encasement can be utilised as it has the affect of changing the buckling mode, which increases the strength and stiffness of the member. This paper describes an experimental program undertaken for both encased and concrete filled composite columns, which were designed to be stocky in nature and thus fail by strength alone. The columns were designed to consider the strength in axial compression and were fabricated from high strength steel plate. In addition to the encased and concrete filled columns, unencased columns and hollow columns were also fabricated and tested to act as calibration specimens. A model for the axial strength was suggested and this is shown to compare well with the test results. Finally aspects of further research are addressed in this paper which include considering the effects of slender columns which may fail by global instabilities.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2010년도 춘계 학술대회 제22권1호
• /
• pp.13-14
• /
• 2010

본 연구는 휨연결재와 횡방향 프레스트레스력으로 보강된 PSC(Prestressed Concrete) 분절 거더의 정적 거동 성능을 검증하는데 목적이 있다. 동일 제원과 재료를 적용하며 일체거더와 횡방향으로 보강되지 않은 분절거더와 3개의 횡방향으로 보강된 분절거더를 사용하여 중앙 경간의 처짐과 중앙 경간 및 연결부에서의 변형률을 측정하였다. 실험결과를 바탕으로 거더의 정적 휨성능을 평가 검증 하고 기존의 연속 거더와 횡구속이 안된 분절 거더의 성능을 비교 분석하였다.

• 한국강구조학회 논문집
• /
• 제17권4호통권77호
• /
• pp.385-394
• /
• 2005

본 논문은 유전자알고리즘과 퍼지이론에 근거한 개선된 퍼지-유전자알고리즘에 의한 이산화 최적설계 프로그램을 개발하였다. 본 연구의 최적설계는 평면 및 입체 강구조물의 단면, 형상 최적설계가 동시에 수행된다. 본 연구에서 목적함수는 강구조물의 중량이고, 제약조건식은 설계 및 좌굴강도, 변위 및 부재단면의 두께에 대한 설계제한식이다. 설계변수는 철골부재 단면의 치수와 절점좌표이다. 그리고 본 연구의 개선된 퍼지-유전자 알고리즘에 의한 이산화 최적설계 프로그램의 적용을 위해 설계 예를 들었다.