• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.4
• /
• pp.287-293
• /
• 2010

Purpose: This study evaluated the effect of polishing techniques on surface roughness of polymethyl methacrylate (PMMA), as well as the influence of light-cured surface glaze and subsequent brushing on surface roughness. Materials and methods: A total of 60 PMMA specimens ($10{\times}10{\times}5\;mm$) were made and then divided into 6 groups of 10 each according to the polymerization methods (under pressure or atmosphere) and the surface polishing methods (mechanical or chemical polishing) including 2 control groups. The mechanical polishing was performed with the carbide denture bur, rubber points and then pumice and lathe wheel. The chemical polishing was performed by applying a light-cured surface glaze ($Plaquit^{(R)}$; Dreve-Dentamid GmbH). Accura $2000^{(R)}$, a non-contact, non-destructive, optical 3-dimensional surface analysis system, was used to measure the surface roughness (Ra) and 3-dimensional images were acquired. The surface roughness was again measured after ultrasonic tooth brushing in order to evaluate the influence of brushing on the surface roughness. The statistical analysis was performed with Mann-Whitney test and t-test using a 95% level of confidence. Results: The chemically polished group showed a statistically lower mean surface roughness in comparison to the mechanically polished group (P = .0045) and the specimens polymerized under the atmospheric pressure presented a more significant difference (P = .0138). After brushing, all of the groups, except the mechanically polished group, presented rougher surfaces and showed no statistically significant differences between groups. Conclusion: Although the surface roughness increased after brushing, the chemical polishing technique presented an improved surface condition in comparison to the mechanical polishing technique.

• The Journal of Korean Society for Radiation Therapy
• /
• v.18 no.2
• /
• pp.81-87
• /
• 2006

Purpose: Few researches have been peformed on the dose distribution of the moving organ for radiotherapy so far. In order to simulate the organ motion caused by respiratory function, multipurpose phantom and moving device was used and dosimetric measurements for dose distribution of the moving organs were conducted in this study. The purpose of our study was to evaluate how dose distributions are changed due to respiratory motion. Materials and Methods: A multipurpose phantom and a moving device were developed for the measurement of the dose distribution of the moving organ due to respiratory function. Acryl chosen design of the phantom was considered the most obvious choice for phantom material. For construction of the phantom, we used acryl and cork with density of $1.14g/cm^3,\;0.32g/cm^3$ respectively. Acryl and cork slab in the phantom were used to simulate the normal organ and lung respectively. The moving phantom system was composed of moving device, moving control system, and acryl and cork phantom. Gafchromic film and EDR2 film were used to measure dose ditrbutions. The moving device system may be driven by two directional step motors and able to perform 2 dimensional movements (x, z axis), but only 1 dimensional movement(z axis) was used for this study. Results: Larger penumbra was shown in the cork phantom than in the acryl phantom. The dose profile and isodose curve of Gafchromic EBT film were not uniform since the film has small optical density responding to the dose. As the organ motion was increased, the blurrings in penumbra, flatness, and symmetry were increased. Most of measurements of dose distrbutions, Gafchromic EBT film has poor flatness and symmetry than EDR2 film, but both penumbra distributions were more or less comparable. Conclusion: The Gafchromic EBT film is more useful as it does not need development and more radiation dose could be exposed than EDR2 film without losing film characteristics. But as response of the optical density of Gafchromic EBT film to dose is low, beam profiles have more fluctuation at Gafchromic EBT. If the multipurpose phantom and moving device are used for treatment Q.A, and its corrections are made, treatment quality should be improved for the moving organs.

• The Transactions of the Korea Information Processing Society
• /
• v.4 no.12
• /
• pp.3159-3174
• /
• 1997

This paper reports a research to develop a methodology and a tool for understanding of very large and complex real-time software. The methodology and the tool mostly developed by the author are called the Architecture-based Real-time Software Understanding (ARSU) and the Software Re/reverse-engineering Environment (SRE) respectively. Due to size and complexity, it is commonly very hard to understand the software during reengineering process. However the research facilitates scalable re/reverse-engineering of such real-time software based on the architecture of the software in three-dimensional perspectives: structural, functional, and behavioral views. Firstly, the structural view reveals the overall architecture, specification (outline), and the algorithm (detail) views of the software, based on hierarchically organized parent-chi1d relationship. The basic building block of the architecture is a software Unit (SWU), generated by user-defined criteria. The architecture facilitates navigation of the software in top-down or bottom-up way. It captures the specification and algorithm views at different levels of abstraction. It also shows the functional and the behavioral information at these levels. Secondly, the functional view includes graphs of data/control flow, input/output, definition/use, variable/reference, etc. Each feature of the view contains different kind of functionality of the software. Thirdly, the behavioral view includes state diagrams, interleaved event lists, etc. This view shows the dynamic properties or the software at runtime. Beside these views, there are a number of other documents: capabilities, interfaces, comments, code, etc. One of the most powerful characteristics of this approach is the capability of abstracting and exploding these dimensional information in the architecture through navigation. These capabilities establish the foundation for scalable and modular understanding of the software. This approach allows engineers to extract reusable components from the software during reengineering process.

• Korean Journal of Weed Science
• /
• v.15 no.1
• /
• pp.85-98
• /
• 1995

Six malformin B's produced by Aspergillus niger van Tiegh. were separated by HPLC. Their structures determined by the methods of amino acid analyses, mass spectrometry, and two-dimensional NMR were revealed as cyclic pentapeptides structurally related to malformin $A_1$. Both the NMR and MS/MS data suggest that the respective structures of separated malformin B's were as follows; cyclo-D-Cys-D-Cys-L-Val-D-Leu-L-allo-Ile for $B_{1a}$, cyclo-D-Cys-D-Cys-L-Val-D-Leu-L-Leu for $B_{1b}$, cyclo-D-Cys-D-Cys-L-Val-D-Val-L-Leu for $B_2$, cyclo-D-Cys-D-Cys-L-Val-D-Ile-L-Leu for $B_3$, cyclo-D-Cys-D-Cys-L-Val-D-Ile-L-Ile for $B_4$, and cyclo-D-Cys-D-Cys-L-Val-D-Val-L-Ile for $B_5$. Among the malformin B's, the structure of $B_{1b}$ was the same as that of malformin $A_3$ or C. All the malformin B's showed physiological activities in the two assay systems using corn(Zea mays L.) roots and mung bean(Phaseolus aureus Roxb.) hypercotyl segments. The malformin B's with molecular weight 529 were more effective for inducing corn root curvature than those with molecular weight 515. The difference in molecular weight of malformin B's, i.e., the retention time on HPLC, results in the polarity change of the whole malformin molecule which affects the revealation of the malformin activities. In addition, the disulfide form of the malformin B's gives the rigidity of the molecule, whereas the combination of the fourth and the fifth amino acid residues provides the optimal three-dimensional configuration to the malformin receptor of plants. Presumably, these two factors are appeared to be essential for the greatest physiological activity of malformin B's. malformin $B_{1a}$ caused the corn root curvature by 90% at a concentration of $0.25{\mu}M$. However, such differential activities with molecular weight of 529 or 515 of malformin B's were not found in the mung bean hypercotyl segment test. Maximum stimulation of mung bean hypercotyl growth was observed at $0.1{\mu}M$ concentration of malformin B's. The growth of the segments treated with $B_5$ was 154% greater than that of the control.

• The korean journal of orthodontics
• /
• v.34 no.5 s.106
• /
• pp.417-428
• /
• 2004

The purpose of this study was to evaluate the stress distributions at the periodontal ligament (PDL) and displacements of the maxillary first molar when mesially directed force was applied under various molar angulations and rotations. A three dimensional finite element model of the maxiilary first molar and its periodontal ligament was made Upright position, mesially angulated position by $20^{\circ}$ and distally angulated position of the same degree were simulated to investigate the effect of molar angulation. An anteriorly directed force of 200g countertipping moment of 1,800gm-mm (9:1 moment/force ratio) and counterrotation moment of 1,000gm-mm (5:1 moment/force ratio) were applied in each situation. To evaluate the effect of molar rotation on the stress distribution, mesial-in rotation by $20^{\circ}$ and the same amount of distal-in rotation were simulated. The same force and moments were applied in each situation. The results were as follows: In all situations, there was no significant difference in mesially directed tooth displacement Also, any differences in stress distributions could not be found, in other words. there were no different mesial movements. Stress distributions and tooth displacement of the $20^{\circ}$ mesially angulated situation were very similar with those of the $20^{\circ}$ distal-in rotated situation. The same phenomenon was obserned between the $20^{\circ}$ distally angulated situation and $20^{\circ}$ mesial-in rotated situation. When the tooth was mesially angulated, or distal-in rotated, mesially directed force made the tooth rotate in the coronal plane. with its roots moving buccally, and its crown moving lingually. When the tooth was distally angulated, or mesial-in rotated, mesially directed force made the tooth rotate in the coronal plane, with its roots moving lingually and its crown moving buccally. When force is applied to au angulated or rotated molar, the orthodontist should understand that additional torque control is needed to prevent unwanted tooth rotation in the coronal plane.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.15 no.1
• /
• pp.13-20
• /
• 1985

The author obtained the oblique lateral trans cranial radiograms from 376 patients (114 of male, and 262 of female) with temporomandibular joint arthrosis. After tracing each film, the author analyzed the dimensional changes of the condylar heads with pain, clicking, mouth opening limitation, and masticatory difficulty respectively, which were the chief complaints of the TMJ arthrosis and compared these data with control group. The results were as follows; 1. There was a great predilection for occurrence of the TMJ arthrosis in female (262 cases) over male (114 cases). But there was no significant difference in ratio between the sexes on each symptom. In male, 60 patients (52.6%) had pain, 28 patients (24.6%) had clicking, 21 patients (18.4%) had mouth opening limitation, and 5 patients (4.4%) had masticatory difficulty. In female, 148 parients (56.5%) had pain, 57 patients (21.8%) had clicking, 47 patients (17.9%) had mouth opening limitation, and 10 patients (3.8%) had masticatory difficulty. 2. Examined controlled group, the author analyzed the dimension of W-W', 0-H, 0-A, 0-B on the right side first, and left side second. In male, the dimension of W-W' was 14.52㎜, 14.13㎜; 0-H was 13.92㎜, 13. 71㎜' 0-A was 8.91㎜, 9.0㎜ and 0-B was 8.67㎜, 8.78㎜. In female, W-W' was 13.77㎜, 13.51㎜; 0-H was 13.42㎜, 13.35㎜; 0-A was 8.92㎜, 9.01㎜; and 0-B was 8.59㎜, 8.80㎜. 3. W-W' and 0-H of the experimental group were distinctly lesser than the controlled group. Male with mouth opening limitation show the least (12.70㎜, 13.00㎜) on W-W', but both sexes with pain show the least on 0-H. There was no significant difference between experimental group with Clicking and controlled group on 0-H, 0-A, and 0-B. And also there was no difference on 0-B in patients with every symptom except masticatory difficulty. The dimensional changes of the condylar heads with those symptoms were as follows; a) In male patients, complaing of pain, W-W' of the right and left was 13.80㎜, 12.80㎜; 0-H was 13.10㎜, 12.90㎜; 0-A was 8.69㎜, 8.18㎜; 0-B was 8.33㎜, 8.42㎜. In female, W-W' was 13.01㎜, 12.90㎜; 0-H was 12.48㎜, 12.80㎜; 0-A was 8.60㎜, 8.49㎜; 0-B was 8.48㎜, 8.50㎜. b) In male patients with clicking, W-W' was 13.70㎜, 13.10㎜; 0-H was 13.90㎜, 13.10㎜; 0-A was 8.81㎜, 8.16㎜ 0-B was 8.34㎜, 8.25㎜. In female, W-W' was 13.10㎜, 13.50㎜; 0-H was 13.30㎜, 12.91㎜; 0-A was 8.95㎜, 8.49㎜; 0-B was 8.23㎜, 8.70㎜. c) In male patients with mouth opening limitation, W-W' was 12.70㎜, 13.00㎜; 0-H was 13.40㎜, 13.40㎜; 0-A was 8.37㎜, 8.48㎜; 0-B was 8.33㎜, 8.62㎜. In female, W-W' was 13.00㎜, 12.50㎜ 0-H was 12.90㎜, 13.10㎜; 0-A was 8.49㎜, 8.09㎜; 0-B was 8.77㎜, 8.01㎜. d) In male patients with masticatory difficulty, W-W' was 13.30㎜, 13.20㎜; 0-H was 13.40㎜, 12.60㎜; 0-A was 8.26㎜, 8.32㎜; 0-B was 7.80㎜, 8.20㎜. In female, W-W' was 12.30㎜, 12.00㎜; 0-H was 13.10㎜, 13.20㎜; 0-A was 8.68㎜, 7.95㎜; 0-B was 7.46㎜, 7.87㎜.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.25 no.2
• /
• pp.117-131
• /
• 2007

Representation of building internal space is an active research area as the need for more geometrically accurate and visually realistic increases. 3 dimensional representation is common ground of research for disciplines such as computer graphics, architectural design and engineering and Geographic Information System (GIS). In many cases CAD plans are the starting point of reconstruction of 3D building models. The main objectives of building reconstruction in GIS applications are visualization and spatial analysis. Hence, CAD plans need to be preprocessed and edited to adapt to the data models of GIS SW and then georeferenced to enable spatial analysis. This study automated the preprocessing of CAD data using AutoCAD VBA (Visual Basic Application), and the processed data was topologically restructured for further analysis in GIS environment. Accuracy of georeferencing CAD data was also examined by comparing the results of coordinate transformation by using digital maps and GPS measurements as the sources of ground control points. The reconstructed buildings were then applied to visualization and network modeling.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.2
• /
• pp.185-189
• /
• 2010

This study considered the feasibility of controlling the air concentration by oscillating flow in fuel cell channels. The fuel cell stack performance is largely influenced by the air concentration. If the air concentration is lower than 2.5 times the stoichiometric of the inlet air, the fuel cell stack performance seriously deteriorates because of air starvation. In this respect, optimizing the air concentration is crucially important to maximizing the fuel cell stack performance. In this work, the effects of oscillating actuation were studied to control the concentration. Studies have shown that there are two non-dimensional key parameters related to the frequency and oscillating amplitude. This paper presents how those parameters affect the performance of the stack.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.3
• /
• pp.353-359
• /
• 2012

The identification of effective root zone would clarify dynamics of plant available water and soil water balance. Using the relationship between soil properties and electrical resistivity (ER) the purpose of this research is to identify soil zone affected by a plant root activity using electrical resistivity tomography (ERT) technique. Four plastic containers were prepared for two different soil textures (clay and sandy loam) and one container for each texture was selected for planting four corn seedlings (Zea mays L.) and the others were prepared for the blank. For ERT monitoring, we prepared 0.8 m plastic sticks with 17 electrodes installed with 5 cm space. The Ministing (AGI Inc., Texas) instrument for electrical resistivity measurement and semi-auto converter of electrode arrangement were set up for dipole-dipole array. During 2 months of the corns growing, ERT monitoring was made 3 to 4 days after the irrigation practice. Despite of the same amount water supplied into soils, two textures showed very different apparent resistivity values due to different clay content. The apparent electrical resistivity is consistently lower in clay loam comparing to sandy loam soil implying that plant root does not significantly alter the overall trend of resistivity. When plant root system, however, is active both soils with plants showed 2-7 times higher electrical resistivity and higher coefficient variation than soils without plant, implying the effect of root system on the resistivity, in which may caused by. This result suggests plant root activities regulating the soil water dynamics mainly control the variation of electrical resistivity over soil textural difference. Therefore the identification of water uptake zone would highly be correlated to plant root activities, thus ERT will be feasible approach to identify spatial characteristics of a plant root activity.

• Korean Journal of Applied Biomechanics
• /
• v.21 no.4
• /
• pp.437-447
• /
• 2011

In this study, the lower limbs joints were analyzed for features based on the biomechanical characteristics of landing techniques according to height and landing on the ground type (flats and downhill). In order to achieve the objectives of the study, changes were analyzed in detail contents such as the height and form of the first landing on the ground at different angles of joints, torso and legs, torso and legs of the difference in the range of angular motion of the joint, the maximum angular difference between joints, the lower limbs joints difference between the maximum moment and the difference between COM changes. The subjects in this study do not last six months did not experience joint injuries 10 males in 20 aged were tested. Experimental tools to analyze were the recording and video equipment. Samsung's SCH-650A model camera was used six units, and the 2 GRF-based AMTI were used BP400800 model. 6-unit-camera synchronized with LED (photo cell) and Line Lock system were used. the output from the camera and the ground reaction force based on the data to synchronize A/D Syc. box was used. To calculate the coordinates of three-dimensional space, $1m{\times}3m{\times}2m$ (X, Y, Z axis) to the size of the control points attached to the framework of 36 markers were used, and 29 where the body was taken by attaching a marker to the surface. Two kinds of land condition, 40cm and 60cm in height, and ground conditions in the form of two kinds of flat and downhill slopes ($10^{\circ}$) of the landing operation was performed and each subject's 3 mean two-way RM ANOVA in SPSS 18.0 was used and this time, all the significant level was set at a=.05. Consequently, analyzing the landing technique as land form and land on the ground, the changes of external environmental factors, and the lower limbs joints' function in the evaluation were significantly different from the slopes. Landing of the slop plane were more load on the joints than landing of plane. Especially, knee extensor moment compared to the two kinds of landing, slopes plane were approximately two times higher than flat plane, and it was statistical significance. Most of all not so much range of motion and angular velocity of the shock to reduce stress was important. In the further research, front landing as well as various direction of motion of kinetic, kinetic factors and EMG variables on lower limbs joints of the study in terms of injury-prevention-approach is going to be needed.