• Microbiology and Biotechnology Letters
• /
• v.23 no.6
• /
• pp.755-762
• /
• 1995

A phenolic resin industrial wastewater containing about 41,000 mg/l of phenol and 2,800 mg/l of formaldehyde was biologically treated by a mixed culture GE2 immobilized on ceramic beads. This study was carried out with three experimental groups : Control-only added the sludge of papermill wastewater ; GE2 treatment-added GE2 to Control ; Ceramic treatment-applied ceramic carrier to GE2 treatment. When the original wastewater was diluted 80 times with aerated tap-water, influent COD$_{Mn}$ WaS 1,140 mg/l and that of the effluent was in the range of 22-35 mg/l, which was not much different among the experimental groups. However, at 20-times dilution, influent COD$_{Mn}$ was 4,800 mg/l and the effluent COD$_{Mn}$ of Control, GE2 treatment and Ceramic treatment was 179, 128 and 94 mg/l, respectively. COD$_{Mn}$, removal efficiency by Ceramic treatment was the highest, at 98.0%. At this time, the effluent phenol concentration of Control, GE2 treatment and Ceramic treatment was 10.71, 7.93 and 5.60, respectively. As the dilution times decreased, the removal efficiency of COD$_{Mn}$ and phenol did not change much, but COD$_{Mn}$ and phenol concentration of the effluent increased. Consequently, it is likely that the phenolic industrial wastewater containing phenol and formaldehyde can be biologically treated using a GE2 and ceramic carrier and that at 40-times dilution, the effluent completely meets the effluent standards for industrial wastewater treatment plant.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.8 no.4
• /
• pp.233-239
• /
• 2003

For the quantitative analysis of an unknown sample a calibration curve should be obtained, as analytical instruments give relative, rather than absolute measurements. Therefore, researchers should make standard samples with various known concentrations, measure each standard and the unknown sample, and then determine the concentration of the unknown by comparing the measured value to those of the standards. These procedures are tedious and time-consuming. Therefore, we developed a polymer based microfluidic device from polydimethylsiloxane, which integrates serial dilution and capillary electrophoresis functions in a single device. The integrated microchip can provide a one-step analytical tool, and thus replace the complex experimental procedures. Two plastic syringes, one containing a buffer solution and the other a standard solution, were connected to two inlet holes on a microchip, and pushed by a hydrodynamic force. The standard sample is serially diluted to various concentrations through the microfluidic networks. The diluted samples are sequentially introduced through microchannels by electro-osmotic force, and their laser-induced fluorescence signals measured by capillary electrophoresis. We demonstrate the integrated microchip performance by measuring the fluorescence signals of fluorescein at various concentrations. The calibration curve obtained from the electropherograms showed the expected linearity.

• Korean Journal of Food Science and Technology
• /
• v.29 no.5
• /
• pp.895-900
• /
• 1997

Cyclodextrin (CD), which is one of food additives, was applied to Takju in oder to suppress the production of a stinking odor which its brewing and storage. CD was added to Takju in two different manners: one right after its brewing dilution stage, the other during its second mashing stage. After equal intervals of time, each sample was tested for fermentation process, storage capability, and sensory characteristics. The amount of CD ranged from 0.1 to 0.3% (w/w). The effect of CD on alcohol concentration, pH, total acidity and sugar content of Takju was shown to be more greatly influenced in the second sample rather than the first. The qualities of Takju were not affected by the addition of CD in the first sample. The sensory evaluation showed that the sample of the brewing dilution stage proved to be more attractive in the level of acceptability. However, when CD was over-added to Takju, the degree of acceptability declined due to the fact that the over-addition of CD suppresses its unique taste and flavor.

• Journal of Microbiology and Biotechnology
• /
• v.9 no.6
• /
• pp.716-721
• /
• 1999

It has been known that continuous cultivation of hairy root is difficult to maintain for a long period of time compared to the microbial and callus cultures. Chemostat cultivation was successfully carried out in order to economically produce a plant-based colorant, betacyanin, from red beet hairy root for more than 85 days in a 14-1 fermentor. The result from the chemostat cultivation was compared to those of the batch and fed-batch cultivations of red beet hairy roots. It was shown that hairy root reached its steady state within 50 days of the cultivation, and then maintained for about 25-30 days in a wide range of dilution rates. Total betacyanin production from the continuous process was also calculated to be 2.65g at 0.28(l/d) of dilution rate, compared to 0.196g from fed-batch cultivation. It was found that betacyanin production was a partially growth related process, yielding 0.376 mg/g-fresh wt. cell and $1.89{\times}10^{-5}$ mg/g-fresh wt. cell/d, with 0.92 of correlation factor in a partial growth-product model. It was also shown that the cell growth required was relatively large for maintenance amount of energy at a low dilution rate. The growth of hairy root was inhibited by high light intensity in following a photo-inhibition model. The growth parameters were estimated to be 0.3(l/d), $10.56kcal/\textrm{m}^2/h$,{\;}and{\;}35.81kcal/\textrm{m}^2/h$ for the maximum specific growth rate, half saturation light intensity, and inhibition light intensity, respectively.

• Korean Journal of Animal Reproduction
• /
• v.24 no.1
• /
• pp.89-95
• /
• 2000

This study was to establish an effective dilution technique in a vitrification of bovine blastocysts for the field trial. For vitrification, blastocysts were exposed in glycerol (G) and ethylene glycol (EG) mixture in m-DPBS supplemented with 10% FBS. Blastocysts were first exposed to 10% (v/v) G for 5 min, and subsequently were transferred to 10% G plus 20% EG (v/v) for 5 min. Finally, embryos were transferred to 25% G plus 25% EG (v/v) for 30 see and were placed in nitrogen vapor for 3 min, and then were plunged into L$N_2$. At thawing, the straw containing blastocysts was placed in air for 10 sec, and then plunged into a water bath at $25^{\circ}C$ until all ice had disappeared. They were placed in $25^{\circ}C$ and 36$^{\circ}C$ water according to treatment group for different time. Also, in vitro survival was assessed by the re-expansion and hatched rates at 24 hand 48 h postwarming, respectively. The results obtained in these experiments were summarized as follows; 1) In the survival rates of vitrified bovine blastocysts according to different dilution time at thawing, the data of 1 min group (86.6, 56.6%) were higher than those of other treatment groups (2 min; 93.5, 35.4%, 2.5 min; 76.9, 30.7%, 3 min; 88.8, 36.1% and 3.5 min; 83.7, 8.1%). 2) When the in vitro survival of vitrified groups according to different developmental stage was examined at 48 h after thawing using 1 min dilution method, the hatching rates of fast developed embryos (expanded blastocyst: 81.3%: early hatching blastocyst: 86.2%) were higher than that of delayed developed one (early blastocyst: 46.6%). 3) In addition, when the in vitro survival of vitrified groups according to different embryo age was compared, the hatched rates at 48 h after thawing of Day 7 (66.6%) and Day 8 embryos (60.0%) were significantly higher than that of Day 9 embryos (22.7%) (P＜0.05). These results demonstrate that vitrified bovine IVM/IVF/IVC blastocysts can be successfully survived in vitro using one-step dilution (1 min) method.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.39 no.3
• /
• pp.1-9
• /
• 2016

NSS (Navigation satellite system) provides the information for determining the position, velocity and time of users in real time using satellite-networking, and is classified into GNSS (Global NSS) and RNSS (Regional NSS). Although GNSS services for global users, the exactitude of provided information is dissatisfied with the degree required in modern systems such as unmanned system, autonomous navigation system for aircraft, ship and others, air-traffic control system. Especially, due to concern about the monopoly status of the countries operating it, some other countries have already considered establishing RNSS. The RNSS services for users within a specific area, however, it not only gives more precise information than those from GNSS, but also can be operated independently from the NSS of other countries. Thus, for Korean RNSS, this paper suggests the methodology to design the satellite constellation considering the regional features of Korean Peninsula. It intends to determine the orbits and the arrangement of navigation satellites for minimizing PDOP (Position dilution of precision). PGA (Parallel Genetic Algorithm) geared to solve this nonlinear optimization problem is proposed and STK (System tool kit) software is used for simulating their space flight. The PGA is composed of several GAs and iterates the process that they search the solution for a problem during the pre-specified generations, and then mutually exchange the superior solutions investigated by each GA. Numerical experiments were performed with increasing from four to seven satellites for Korean RNSS. When the RNSS was established by seven satellites, the time ratio that PDOP was measured to less than 5 (i.e. better than 'Good' level on the meaning of the PDOP value) was found to 94.3% and PDOP was always kept at 10 or less (i.e. better than 'Moderate' level).

• The Korea Journal of Herbology
• /
• v.30 no.5
• /
• pp.15-21
• /
• 2015

Objectives : Methicillin-resistantStaphylococcus aureus(MRSA) is a human pathogen. New antibacterial agents are needed to treat MRSA-related infections. This study investigated the antibacterial activity of EtOH 70% extracts ofTonghyeonipal-dan(THD) which prescription is composed of oriental medicine against MRSA.Methods : The antibacterial activity of THD was evaluated against MRSA strains by using the Disc diffusion method, broth microdilution method, Checkerboard dilution test, and Time-kill test; its mechanism of action was investigated by bacteriolysis, detergent or ATPase inhibitors were used.Results : The minimum inhibitory concentration (MIC) of THD is 1,000~2,000 μg/mL against MRSA. In the checkerboard dilution test, fractional inhibitory concentration index (FICI) of THD in combination with antibiotics indicated synergy or partial synergism againstS. aureus. Furthermore, a time-kill assay showed that the growth of the tasted bacteria was considerably inhibited after 24 h of treatment with the combination of THD with selected antibiotics. For measurement of cell membrane permeability, THD 500 μg/mL along with concentration of Triton X-100 (TX) and Tris-(hydroxymethyl) aminomethane (TRIS) were used. In the other hand, N,N-dicyclohexylcarbodimide (DCCD) and Sodium azide (NaN3) were used as an inhibitor of ATPase. TX, TRIS, DCCD and NaN3 cooperation againstS. aureusshowed synergistic action.Conclusions : Accordingly, antimicrobial activity of THD was affected by cell membrane and inhibitor of ATPase were assessed. These results suggest that THD has antibacterial activity, and that THD extract offers great potential as a natural antibiotic against MRSA.

• Journal of the Korean Vacuum Society
• /
• v.17 no.2
• /
• pp.113-116
• /
• 2008

As the integration in semiconductor display develops, semiconductor process becomes multilayer. In order to form several layer patterns, etching process which uses photoresistor (PR) must be performed in multilayer process. Repeated etching processes which take long time and PR residue cause mortal problems in semiconductor. To overcome such problems, we studied about the solution which eliminates PR effectively by using normal dry and wet etching method using plasma activated PR strip solvent in liquid condition. At first, we simulate the device which activates the plasma and make sure whether gas flow in device is uniform or not. Under activated plasma, etching effect is elevated. This improvement reduces etching time as well as display production time of semiconductor process. Generally, increasing etching process increases environmental hazards. Reducing etching process can save the etchant and protect environment as well.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.8 no.3
• /
• pp.118-123
• /
• 2000

Food waste results in various problems such as decay, odors and leachate in collection, transportation and landfill due to the high volatile solids and moisture content. Acidogenic fermentation of food waste is influenced by the environmental conditions such as pH, retention time, etc. Each component of food waste is degraded under the different environmental conditions. Starch, cellulose and protein have their own optimum pHs and retention times for degradation. The degradation of starch increases at low pH, cellulose with increasing retention time, and protein with increasing retention time as well as approaching neutral pH. These mean that the degradation of food waste can be enhanced by adjusting the environmental conditions of acidogenic fermentation. The efficiency of acidification increased from 71.2 to 81.1% by controlling dilution(D) rate from 3.0 to $1.0d^{-1}$ depending on the state of the fermentation. The main component of the acidified product was shifted from butyric to acetic acid, indicating that the increase of acidification was mainly caused by the enhanced degradation of vegetables and meats.

• Asian-Australasian Journal of Animal Sciences
• /
• v.13 no.4
• /
• pp.464-469
• /
• 2000

Experiments were conducted to determine the effects of soybean meal (SBM) as a source of protein and sago meal (SM) as a source of carbohydrate on in situ and in vivo digestibility of dietary components in four male goats (Kambing Katjang) and four male sheep (Malin) weighing 25-35 kg. Rumen volume, as well as rumen fluid dilution rate were also determined. The animals were housed in single pens with individual feeding and drinking troughs and each animal was fitted with a rumen fistula. They were fed two diets : chopped rice straw+200 g soybean meal (SBM), and chopped rice straw+190 g soybean meal+300 g sago meal (SBM+SM). Rice straw was offered ad libitum. The supplements were isonitrogenous (80 g crude protein/animal/d), but the proportions of dry matter (DM), organic matter (OM), crude fibre (CF), neutral detergent fibre (NDF) and acid detergent fibre (ADF) were lower in the SBM supplement (191, 165, 11, 40, 15 g/animal/d for DM, OM, CF, NDF and ADF, respectively) than in the SBM+SM supplement (445, 423, 25, 102, 38 g/animal/d for DM, OM, CF, NDF and ADF, respectively). Two animals from each species were fed either supplement in a cross-over design in two periods. Each period lasted for four weeks. In situ and in vivo digestibility studies were carried out, followed by the determination of rumen volume and rumen fluid dilution rate. The results showed that straw DM and total DM intakes of goats (average of $48.7g/kg\;W^{0.75}$, $72.7g/kg\;W^{0.75}$, respectively) were significantly (p<0.01) higher than sheep (average of $3.56g/kg\;W^{0.75}$, $61.6g/kg\;W^{0.75}$, respectively), but OM, N and GE intakes were not significantly different between the two animal species. When the effect of supplements was compared, animals fed SBM+SM supplement had significantly (p<0.001) higher DM, OM and GE intakes than animals fed SBM supplement. Potential degradabilities of rice straw DM were significantly (p<0.01) higher in goats (average of 48.8%) than in sheep (average of 46.1 %). The supplements had no significant effect on the potential degradabilities of DM, OM and NDF, but they had a significant (p<0.05) effect on the degradation rates of DM and NDF. The addition of sago meal in the diet reduced the degradation rates of DM and NDF of rice straw in the rumen. Potential degradability of DM of soybean meal was not significantly different between animal species as well as between supplements. Sago meal was highly degradable. At 24 h of incubation in the rumen, 90-95% of DM loss was observed. There was a significant interaction between animal species and supplements in the in vivo digestibility of ADF and GE. In animals fed SBM supplement, the in vivo digestibility of ADF was significantly (p<0.05) higher in goats ($50.6{\pm}4.22%$) than in sheep ($44.4{\pm}3.21%$), but digestibility of GE was significantly (p<0.05) higher in sheep ($70.2{\pm}1.93%$) than in goats ($63.0{\pm}3.07%$). The digestibility values of CP and OM were significantly (p<0.05) higher in sheep when compared to goats. Animals fed SBM+SM supplement showed significantly (p<0.05) higher DM and OM digestibility values than animals fed SBM supplement, but digestibility values of CP were significantly (p<0.05) higher in animals fed SBM supplement. Differences in in vivo digestibility values of CF and NDF were not significantly different between animal species or supplements. Water intake, rumen volume ($1/kg\;W^{0.75}$), rumen fluid dilution rate and mean retention time were similar between the two animal species. However, rumen fluid dilution rate and mean retention time was significantly (p<0.01) affected by supplements. Animals fed SBM+SM had faster rumen fluid dilution rate and consequently shorter mean retention time.