• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.5
• /
• pp.561-568
• /
• 2003

An experiment using high preheated air in a turbulent non-premixed flame was performed to investigate the effects of high preheated air on the combustion characteristics. Combustion using high preheated and diluted air with flue gas is a new technology which enables NO emission to be reduced. In this study, Na was used as diluent and propane as fuel. Combustion characteristics, especially the distributions of the flame temperature, NO concentration and OH radical intensity were examined under the condition of 300 K, 600 K, 1000 K in terms of the combustion air temperature, and also under the condition of the dilution level from 21% to 13% in terms of oxygen concentration. As the preheated air temperature increased, it appeared that the flame length became shorter, maximum flame temperature increased, the reaction region moved to upstream, and NO concentration increased, but the flame temperature's fluctuation was reduced. In opposite, it was shown with decrement of oxygen concentration at the maximum temperature that both maximum value and the gradient of the flame temperature decreased, and NO emission also decreased considerably, but its fluctuation became larger, being inclined to be unstable.

• 한국연소학회:학술대회논문집
• /
• 2001.11a
• /
• pp.90-96
• /
• 2001

Catalytic ignition of $H_2/O_2/CO_2$ mixtures over platinum catalyst is experimentally investigated by using microcalorimetry. For comparison, $N_2$ and Ar is also used as diluent gas. The gas mixture flows toward platinum foil heated by electric current at atmosphere pressure and ambient temperature. The ignition temperature range 350-445K according to the fuel ratio, dilution ratio and diluent gas. It increases as the fuel ratio and dilution ratio increase. $H_2/O_2$ mixture with $CO_2$ ignites at higher temperature than with other diluents by 30-50K. Several experimental evidences show the inhibition effects of $CO_2$ in $H_2-O_2$ heterogeneous reaction is considerable

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.6
• /
• pp.633-640
• /
• 2011

In this study, the stabilization of an edge flame and the intensity variation of a diffusion branch were investigated using a multi-slot combustor under conditions of high temperature and small fuel-concentration gradient (FCG). The combustor consists of three narrow channels: a quartz channel and two side-heating combustors. For the accuracy of this experimental study, quantitative analysis was carried out for each boundary condition. Stable edge flames could be observed under high-temperature conditions by controlling the FCG and fuel dilution ratio. Moreover, it was found that the intensity of the diffusion flame was increased by increasing the temperature of the mixture. On the contrary, the intensity of the diffusion flame was decreased by increasing the dilution ratio. It was also found that a propane flame is more sensitively affected by these experimental parameters than a methane flame.

• Journal of Korea Water Resources Association
• /
• v.32 no.2
• /
• pp.153-162
• /
• 1999

In this study, mixing and dilution characteristics of vertical multijet discharged by multiport diffuser into stagnant water are investigated. The results obtained from the experiment of multiport diffuser performed in the three dimensional flume are as follows. As far as merging process of multiport diffuser is concerned, merging starts at about z/l = 3 although merging length is dependent upon stability condition and thereafter lateral temperature distribution becomes gradually uniform which is typical distribution of plane jet. Analyses of experimental data for minimum dilution show that characteristics of minimum dilution are described based on three regions which are jet region where momentum is dominated, intermediate region, and plume region where buoyancy is dominated. Minimum dilution coefficient in plume region of multiport diffuser obtained in this study is 15% higher than that of plane diffuser. This is because individual jet of multiport diffuser entrains more ambient water before merging is occurred, and therefore dilution increases.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.8
• /
• pp.639-648
• /
• 2013

This paper describes on the NOx/CO emission characteristics, temperature characteristics and flame structures when firing coal derived synthetic gas especially for gases of Buggenum and Taean IGCC. These combustion characteristics were observed by conducting ambient-pressure elevated-temperature combustion tests in GE7EA model combustor when varying heat input and nitrogen dilution ratio. Nitrogen addition caused decrement in adiabatic flame temperature, thus resulting in the NOx reduction. At low heat input condition, nitrogen dilution raised the CO emission dramatically due to incomplete combustion. These NOx reduction and CO arising phenomena were observed at certain flame temperature of $1500^{\circ}C$ and $1250^{\circ}C$, respectively. As increasing nitrogen dilution, adiabatic flame temperature and combustor liner temperature were decreased and singular points were detected due to change in flame structure such as flame lifting. From the results, the effect of nitrogen dilution on the NOx/CO and flame structure was examined, and the test data will be utilized as a reference to achieve optimal operating condition of the Taean IGCC demonstration plant.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.632-635
• /
• 2001

Microcrystalline Si films have been deposited by using five W-wire filaments of 0.5 mm diameter for hot-wire chemical vapor deposition (HWCVD). We compared the HWCVD grown films with the film exposed to transformer couple plasma system for the modification of seed layer. W-wire filament temperature was maintained below 1600$^{\circ}C$ to avoid metal contamination by thermal evaporation at the filament. Deposition conditions were varied with H$_2$dilution ratio, with and without plasma treatment. From the Raman spectra analysis, we observed that the film crystallization was strongly influenced by the H$_2$dilution ratio and weakly depended on the distance between the wire and a substrate. We were able to achieve the crystalline volume fraction of about 70% with an SiH$_4$/H$_2$ratio of 1.3%, a wire temperature of 1514$^{\circ}C$, a substrate separation distance of 4cm, and a chamber pressure of 38 mTorr. We investigated the influence of ${\mu}$c-Si film properties by using a plasma treatment. This article also deals with the influence of the H$_2$dilution ratio in crystallization modification.

• Journal of the Korean Ceramic Society
• /
• v.32 no.6
• /
• pp.659-668
• /
• 1995

Zirconium carbide was prepared from the mixture of metal zirconium and carbon powders in argon atmosphere by Self-propagating High-temperature Synthesis (SHS) in order to obtain the best carbon source and dilution contents. The most exellent result was obtained in the case that active carbon was added as a starting material, 20~30 wt% dilution content. From thermal profile analysis an apparent activation energy of 118 KJ/mol was calculated. The maximum heating rate achieved during 15 wt% ZrC reaction by product dilution method was approximately 1.54$\times$105 K/s. Coupling this value with the measured wave velocity of 1.026cm/s yielded a maximum thermal gradient fo $1.5\times$105 K/cm. Using the definition of t* and the measured wave velocity, the effective thermal diffusivity, $\alpha$, was calculated to be 0.62$\times$102 $\textrm{cm}^2$/s.

• Tribology and Lubricants
• /
• v.24 no.1
• /
• pp.1-6
• /
• 2008

An experimental study was conducted to evaluate the viscosity characteristics of multi-grade engine oils in which contain diesel fuels. Unused engine oils of SAE 5W40, 10W40 and 15W40 were blended with a diesel fuel ratio of 5%, 10%, and 15%. The viscosity of a diluted engine oil was measured with temperature variation ranging from $-20^{\circ}C$ to $120^{\circ}C$ using a rotary viscometer. The diluted engine oil in which is blended to a diesel fuel plays an important role for decreasing an engine oil viscosity, which may decrease the oil film thickness and a load-carrying capacity. Test results show that the viscosity tends to fall for the increased temperature when engine oil is mixed with a diesel fuel. Especially, the viscosity at a low temperature zone is radically decreased compared with a high temperature zone. Based on the experimental results, the empirical equation that can predict the viscosity of diluted engine oil is expressed in the exponential function with the variation of the temperature and a fuel ratio of diluted engine oil. This equation may be possible to predict the limitation of the oil-fuel dilution rate at the concept design stage of the CDPF system, which doesn't affect the influence of the tribological components.

• Solar Energy
• /
• v.9 no.2
• /
• pp.42-50
• /
• 1989

The Buoyant Jets were analysed experimentally changing flow rate (0.0291/s, 0.0371/s, 0.0451/s), ratio of nozzle tip area to throat area (aspect ratio ${\beta}$=0.4, 1.0, 1.9), and also the temperature difference (${\Delta}T=Ti-T{\infty}$) between the temperature of the inflow water into the storage tank ($1m{\times}1m{\times}3m$) and the mean temperature of the water in the storage tank were changed as $25^{\circ}C,\;35^{\circ}C$ and $45^{\circ}C$. The more aspect ratio decreased, the more the trajectories of Buoyant Jets center-line were decreased and not the more the trajectories of Buoyant Jets centerline were influenced by the increment of the difference of the temperature. The more aspect ratio decreased, the more the half widths and dilution ratio of Buoyant Jets were increased and not the more the half widths and dilution ratio of Buoyant Jets were influenced by the increment of the difference of the temperature. Fr number is the factor that can predict the flow pattern over the whole flow field. And yet for the consideration the near field of Buoyant Jets flow pattern is dominated by magnitude of momentum and buoyancy force.

• Journal of the Korean Vacuum Society
• /
• v.7 no.1
• /
• pp.29-34
• /
• 1998

The solid-phase crystallization (SPC) of plasma-enhanced chemical vapor depsoited (PECVD) amorphous silicon (a-Si) films ha s been investigated by x-ray diffraction (XRD). The a-Si films were prepared on Si (100) wafers using $SiH_4$ gas and without $H_2$ dilution at the substrate temperatures between $120^{\circ}C$ and $380^{\circ}C$, and than annealed at $600^{\circ}C$ for crystallization. The annealed samples exhibited (111), (220), and (311) XRD peaks with preferential orientation of (111). The XRD peak intensities increased as the substrate temperature decreased, and the $H_2$dilution suppressed the solid-phase crystallization. The average grain size estimated by XRD analysis for the (111) texture has increased from about 10 nm to about 30 nm, as the substrate temperature decreased. The deposition rate also increased with the decreasing substrate temperature and the grain size was closely dependent on the deposition rate of the films. The grain size enhancement was attributed to an increase of the structural disorder of the Si network.