• 대한기계학회논문집B
• /
• 제23권9호
• /
• pp.1139-1150
• /
• 1999

The evolution of silica aggregate particles in coflow diffusion flames has been studied experimentally using light scattering and thermophoretic sampling techniques. The measurements of scattering cross section from $90^{\circ}$ light scattering have been utilized to calculate the aggregate number density and volume fraction using with combination of measuring the particle size and morphology through the localized sampling and a TEM image analysis. Aggregate or particle number densities and volume fractions were calculated using Rayleigh-Debye-Gans and Mie theory for fractal aggregates and spherical particles, respectively. Of particular interests are the effects of flame temperature on the evolution of silica aggregate particles. As the flow rate of $H_2$ increases, the primary particle diameters of silica aggregates have been first decreased, but, further increase of $H_2$ flow rate causes the diameter of primary particles to increase and for sufficiently larger flow rates, the fractal aggregates finally become spherical particles. The variation of primary particle size along the upward jet centerline and the effect of burner configuration have also been studied.

• 대한기계학회논문집B
• /
• 제21권4호
• /
• pp.486-493
• /
• 1997

Experimental investigations on the comparison of developments between transient jets and evolving jet diffusion flames have been made in initial injection period. To achieve this experiment, an ignition technique using a residual flame as the ignition source is devised. High speed Schlieren visualizations, and measurements including jet tip penetration velocities and jet widths of the primary vortex are employed to examine the developing processes for several flow conditions. It is seen that the developing behaviors in the presence of flame are greatly different from those in transient jet, and thus the flow characteristics in the transient part are also modified. The discernible differences are shown to consist of the delay of the rollup of the primary vortex, the faster spreading after the rollup due to exothermic expansion, and the survival of only a primary vortex. The growth of primary vortex in the transient jet is properly explained through an impulsively started laminar vortex prior to the interaction. It is also found that the jet tip penetration velocity varies with elapsed time and an increase in Res gives rise to a higher tip penetration velocity.

• 대한기계학회논문집B
• /
• 제30권10호
• /
• pp.973-981
• /
• 2006

Recently there is an increasing interest in particulate matter emission because of new emission regulations, health awareness and environmental problems. It requires to improve particulate measurement techniques as well as to reduce soot emissions from combustion systems. As mentioned above, it is demanded that reduction techniques together with measurement techniques of exhausted particulate matters in combustion systems such as vehicles. However, measurement techniques of particulate matters should be prior to reduction techniques of that because it is able to know an increase and a decrease of exhausted particulate matters when measured particulate matters. Therefore, in this study, we report the measurement of soot primary-particle size using time-resolved laser induced incandescence (TIRE-LII) technique in laminar ethylene diffusion flame. As an optical method, laser induced incandescence is one of well known methods to get information for spatial and temporal soot volume fraction and soot primary particle size. Furthermore, TIRE-LII is able to measure soot primary particle size that is decided to solve the decay ate of signal S $(t_1)$ and S $(t_2)$ at two detection time. In laminar ethylene diffusion flame, visual flame height is 40 mm from burner tip and measurement points are height of 15, 20, 27.5, 30 mm above burner tip along radial direction. As increasing the height of the flame from burne. tip, primary particle size was increased to HAB(Height Above Burner tip)=20mm, and then decreased from HAB=27.5 mm to 30 mm. This results show the growth and oxidation processes for soot particles formed by combustion.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 제26회 KOSCO SYMPOSIUM 논문집
• /
• pp.255-260
• /
• 2003

Characteristics of methane jet diffusion flames using pure oxygen with recirculating $CO_{2}$ as an oxidizer were investigated experimentally. A coflow burner was considered, and the diameter of confinement was larger than that of the coflow. No stabilized flame could be observed over 75% of $CO_{2}$ volume percent. A comparison between air and $O_{2}/CO_{2}$ mixture was made in terms of liftoff velocity, flame liftoff height, and blowout conditions. As results, more stable flame could be observed with $O_{2}/CO_{2}$ mixture for the case of having similar flame temperature.

• 한국연소학회지
• /
• 제10권1호
• /
• pp.13-19
• /
• 2005

Measurements of flame length and NOx emissions have been conducted to investigate the effects of acoustic excitation on flame structure in turbulent hydrogen diffusion flames with coaxial air. When the acoustic excitation of a specific frequency is applied to coaxial air stream, flame length is dramatically reduced, resulting in reduction of flame residence time. Consequently, EINOx could decrease up to 35 % and this shows that acoustic excitation is effective in reducing NOx emissions. Mie scattering technique has been used to visualize the vortex structure induced by acoustic excitation and vortex formation, development and destruction were observed quantitatively. As a result, vortex entrains coflow air into fuel stream and mixing rate between fuel and air is significantly enhanced, which may contribute to reduction of NOx emissions.

• 한국연소학회지
• /
• 제8권2호
• /
• pp.50-55
• /
• 2003

Synthesis of carbon nanofibers on a metal substrate by an ethylene fueled inverse diffusion flame was observed. Stainless steel plates were used for the catalytic metal substrate. The effects of radial distance and residence time of the substrate were investigated. The role of hydrocarbon composition in the fuel was also viewed. Nanofibers with a diameter range of 30-70nm were found on the substrate. The carbon nanofibers were formed and grown in the region from 4 to 5.5mm from the central axis of a flame outside of the visible flame front in the radial direction. The minimum residence time required for the formation of carbon nanofibers were about 20 seconds, and over 60 seconds were required for the full-scale growth. The characteristic time of the formation of carbon nanofibers was much shorter than that of the substrate temperature growth. In this study, the variation in hydrocarbon composition had no significant effect on the formation and growth of the carbon nanofibers.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2001년도 제23회 KOSCO SYMPOSIUM 논문집
• /
• pp.51-56
• /
• 2001

An experiment using preheated air in the coaxial diffusion flame burner was carried out in order to decrease NOx emission and improve the thermal efficiency. Preheated air combustion generally produces high NOx emissions but it was known very well to reduce NOx emission by diluting the combustion air with inert gas in preheated air combustion. In our study, $N_2$ gas was used for diluent and propane was utilized for fuel. We set the combustion air temperature on 300K, 500K, 700K, 900K and dilution level from 21% to 10% in terms of oxygen concentration. NOx emission increased along increment of combustion air temperature and decreased along increment of dilution level(lowering of oxygen concentration in combustion air). Flame-off limit with dilution level enhanced, flame length became longer and the location of maximum flame temperature became lower with increasing of combustion air temperature.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2001년도 제22회 KOSCI SYMPOSIUM 논문집
• /
• pp.60-66
• /
• 2001

Combustion using pure oxygen instead of air is an energy saving technology that can increase thermal efficiency by the improvement of burning rate and ultra high temperature flame, being used on the industrial spot. But information about it is not so enough yet. Flame figure, temperature distribution and emission concentration were measured with oxygen excess ratio and swirl number in a turbulent diffusion flame to investigate the combustion characteristics using pure oxygen. The results showed that flame figure became different as long as oxygen excess ratio varied and that concentration of NO and CO increased suddenly around ${\lambda}$=1.5.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2005년도 제31회 KOSCO SYMPOSIUM 논문집
• /
• pp.305-313
• /
• 2005

Measurements of flame length, width and NOx emissions have been conducted to investigate the effect of an acoustic excitation on flame structure in turbulent hydrogen diffusion flames with coaxial air. The resonance frequency of oscillations was varied between 259 ,514 and 728 Hz with power rate of 0.405 and 2.88w. When these frequencies imposed to hydrogen flames, dramatic reduction of flame length and NOx emission was achieved. And acetone planar laser-induced fluorescence technique was used to measure a concentration of the near field of driven axisymmetric jet. The air-fuel stoichiometric line was plotted to investigate the mixing layer and development of air entrainment to fuel jet. Consequently, acoustic excitation on flame could enhance the air-fuel mixing resulting in abatement of NOx emission quantitatively.

• 대한기계학회논문집
• /
• 제7권3호
• /
• pp.328-334
• /
• 1983

The turbulent hydrogen-air diffussion flame was studied experimentally and theoretically. Laser Doppler anemometer was used to measure the velocity field in the flame. Two mathematical models for the combustion reaction term, which are infinite rate model and finite rate to be derived eddy break-up model, were tested by comparing predictions with experimental data for coaxial turbulent diffusion flame. The agreement between the predictions and the data is, on the whole, very good in the case of employing the finite rate model rather than the infinite rate model. But, it was shown that the finite rate model was practically applicable to the predictions of the turbulent diffussion flame structure.