• 한국광학회지
• /
• 제32권5호
• /
• pp.220-229
• /
• 2021

눈부심 방지를 위한 확산판의 투과율과 연색지수 향상을 위한 양자점 필름의 농도가 고출력 직하형 백색 LED 조명의 광특성에 미치는 영향을 조사했다. 확산판의 투과율이 감소할 경우 조명의 휘도는 줄어들었고 색좌표, 상관색온도는 별다른 변화를 보이지 않았으며 연색지수는 약간 상승했다. 시야각에 따른 광특성의 편차는 거의 없었고 휘도 분포는 람버시안 분포에 가까웠다. 양자점 필름의 농도가 증가할 경우 스펙트럼 상 적색 성분이 늘어나면서 이 성분의 비중을 표현하는 색좌표 x가 증가했고 상관색온도는 약 6000 K에서 4000 K 부근으로 현저히 감소했다. 아울러 조명의 구조를 최적화하면 연색지수가 95까지 증가함을 확인했다. 이런 결과는 적절한 투과율의 확산판과 양자점 필름의 조합을 통해 눈부심이 없고 시야각에 따른 색편차가 거의 없으며 특히 색좌표의 가변이 가능한 고연색성의 조명 구현이 가능함을 보여준다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2003년도 The Fifth Asian Computational Fluid Dynamics Conference
• /
• pp.243-243
• /
• 2003

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.811-814
• /
• 2002

Using a mathematical theory, we show that the optimality condition of a turbulent diffuser with maximum pressure recovery at the exit is zero shear stress along the wall. The optimal diffuser shape is designed through iterative procedures by using the $k-{\varepsilon}-{\nu}^{2}-f$ turbulence model for flow simulation. The Reynolds number based on the bulk mean velocity and the channel height at the diffuser entrance is 18,000. We also perform large eddy simulation to validate the shape design results and investigate the flow characteristics near the zero-skin friction wall. Results from large eddy simulation show that the skin friction is slightly higher than zero but is still very small as compared to that of the flat plate boundary layer flow Although the time-averaged wall shear stress is slightly above zero along the diffuser wall, instantaneous flow reversals occur intermittently. The streamwise mein velocity shows an asymptotic behavior of the half-power-law near the wall where the skin friction is close to zero.

• 한국환경보건학회지
• /
• 제29권1호
• /
• pp.28-33
• /
• 2003

This study was carried out to treat sewage using sand trench combined with septic tank process in rural areas. In order to find optimum parameters, design and operation mode was changed from Run 1 to Run 4. In order to facilitate nitrification and T-P removal, diffuser and iron plate was installed in the 3rd trench of Run 2 period. The septic tank played a role as pre-application process of sand trench system. The removal efficiencies of COD, NH$_4$-N, T-P at steady state were 94.6%, 87.9% and 54.5%, respectively. Addition of diffuser and iron plate in the 3rd trench has increased the removal efficiencies of the NIL-N and T-P. In this system, denitrification were not occurred because of the high DO.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.535-536
• /
• 2006

Researches about micro technology travel lively in these days. Such many researches are concentrated in the field of materials and a process field. But properties of micro materials should be known to give results of research developed into still more. In these various material properties, reliability data such as mechanical, optical, thermal property, etc is the basic property. In this paper, it is measured that is material properties of main BLU(Back Light Unit) components in LCD(Liquid Crystal Display). The pattern shape of prism sheet, diffuser film and reflective plate are measured by variable 3D scanning equipments. It is researched which is the method to measure an optimal 3D pattern shape in each components.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2004년도 요약집 춘계학술발표대회
• /
• pp.118.1-118.1
• /
• 2004

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1999년도 유체기계 연구개발 발표회 논문집
• /
• pp.55-60
• /
• 1999

A centrifugal compressor was tested with three different diffusers with plate vanes. The vane inlet angle was varied from 15 to 30 dog. The higher static pressure rises are obtained with lower vane stagger angle. In the stable region the static pressure field in vaneless space is very sensitive to flow rate. The impeller has a stabilizing effect over the whole stable operating range. The diffuser has a stabilizing effect at high flow rate but is destabilizing at low flow rate.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.463-467
• /
• 2004

This paper presents the fabrication possibility of the micro actuator which uses a micro-thermal bubble, generated b micro-heater under pulse heating. The valve-less micropump using the diffuser/nozzle is consists of the lower plate, he middle plate, the upper plate. The lower plate includes the channel and chamber are fabricated on high processability silicon wafer by the DRIE(Deep Reactive Ion Etching) process. The middle plate includes the chamber and diaphragm d the upper plate is the micro-heater. The Micropump is fabricated by bonding process of the three layer. This paper resented the possibility of the PCR chip operation by the fabricated micropump.

• 청정기술
• /
• 제25권2호
• /
• pp.147-152
• /
• 2019

각종 산업시설과 발전시설에서 배출되는 입자상 물질의 문제로 인하여, 입자상 물질의 제거 효율이 뛰어난 전기집진기의 중요성이 증가하고 있다. 전기집진기의 효율은 전기집진기 내부의 유동분포에 매우 큰 영향을 받으므로, 전기집진기 내부의 유동 균일화를 위한 연구가 지속적으로 이루어지고 있다. 본 연구에서는 유입부, 디퓨저, 본체, 수축부로 구성된 길이 3.5 m, 높이 0.875 m 전기집진기를 제작하였다. 디퓨저에는 3개의 타공판을 설치하였다. 5개의 피토관을 높이 방향으로 부착하여 전기집진기 단면 55지점의 유속을 측정하였다. 디퓨저에 타공판이 설치되었을 때, 전기집진기 내부의 유동분포는 RMS%를 이용하여 평가하였다. 또한 타공판의 타공률 변화에 따른 유속분포도 분석하였다. 그 결과, 타공판이 전기집진기 내부의 유동분포에 미치는 영향이 매우 큼을 확인하였고, 디퓨저 입구에서부터 40%, 50%, 50% 타공률을 가진 타공판을 설치하였을 때, 가장 균일한 유동분포를 나타내었다.

• 설비공학논문집
• /
• 제16권11호
• /
• pp.1077-1083
• /
• 2004

This study is to systematically analyze the effect of various kinds of design factors on the performance of stratified thermal storage tank. Taguchi method, known as a very reasonable tool in the parametric study, is employed in the present work. Three dimensional unsteady numerical experiment is conducted for 4 design parameters of stratified thermal storage tank: inlet Reynolds number, Froude number, diffuser size d with 3 levels (Re=400, 800, 1200, Fr=0.5, 1.0, 2.0 and d=150 mm, 200mm, 300 mm) and diffuser shape with 2 levels. Orthogonal array $L_{18}(2{\times}3^7)$ is adopted for the analysis of variance. The result gives quantitative estimation of the various design parameters affecting the performance and helps to select the main factors for the optimum design of stratified thermal storage tank. Reynolds number is found to be the most dominant parameter and the diffuser shape plays significant role on the performance of stratified thermal storage tank. Based on this finding, the prior questions on the contribution of the diffuser shape proposed by the authors become clear. The optimum condition for the performance is a set of d=300mm, Re=800, and radial regulated plate diffuser. Conformation test shows the repeatability in the analysis and $1.3\%$ difference between the estimated thermocline thickness and that of numerical result.